Modulation
the varying of amplitude, frequency, or phase.
See Also: Optical Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
Product
Disciplined OCXOS
-
GPS Disciplined OCXOs (Oven Controlled Crystal Oscillators) are a range of advanced clock modules which provide electrical timing functionality for distributed network systems. These units primarily revolve around the 1PPS (pulse per second) timing synchronisation signal produced by a GPS frequency receiver which is derived from transmitted timing information received from GPS satellite systems.
-
Product
NI-9852, 2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
779707-01
CAN Interface
2-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI-9852 is a fault‑tolerant Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9852 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9852 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9852 is only compatible with CompactRIO systems.
-
-
Product
Chassis - Up to Four 8x1 Modules, Eight 4x1 Modules or Mixtures of 8x1's, 4x1's, 2x1's & 2x2 Modules in Any Combination or Configuration
CXAR/32-MF
Chassis
These Chassis controls up to four 8x1 modules, eight 4x1 modules or mixtures of 8x1's, 4x1's, 2x1's and 2x2 modules in any combination or configuration. LEDs on the front panel show switch and power status. Add Switch Modules and a Control Module to complete the system. Pushbutton manual control is optional.
-
Product
PXI/PXIe High Density Precision Resistor Module, 18-Channel
40-297A-014
Programmable Resistor Modules
The 40-297A-014 (PXI) and the 42-297A-014 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 470 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-142-HI
-
The 40-230-142-HI (PXI) and 42-230-142-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 392kΩ with 0.5Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Compact Transmitter Module
AMC-I
-
Virginia Diodes'' Signal Generator Extension Modules (SGXs) provide high performance frequency extension of microwave signal generators into the THz range. VDI now offers integrated Amplifier / Multiplier Chains that provide industry leading performance in a compact package.
-
Product
16 Channel Isolated Analog Output Module
DP-cPCI-2502
-
The DP-cPCI-2502 is a 16 channel analog output module organized in four groups of 4 channels each. Each group is isolated with respect to each other and with respect to the system using optical isolators and DC-DC converters. Each output channel is driven by a 16 bit resolution precision DAC. The input digital data is converted to analog signals of ±10V range. The digital data for the DACs is written from the cPCI interface via two banks of latches enabling a double buffered output scheme.
-
Product
Low Profile Front Panel For PCIe Remote Control Interface Card
53-921-LPF
-
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signaling. The 43-921 PCI Express-to-PXI Express expansion kit provides additional PXI instruments slots to the host computer by implementing a PCI Express-based control of PXI modules. The technology consists of a 53-921-001 host adapter installed in the host computer, a PCIe x8 cable, and a 43-921-00x, a remote controller with the 3U (Eurocard) expansion module. 53-921-001 comes in a PCI Express x8 footprint and equips with PCIe x8 cable connector.
-
Product
Distributed Single-Axis Motion Control Modules for Mitsubishi, Yaskawa and Panasonic
MNET-MIA
Motion Controller
ADLINK's Motionnet products provide system integrators with a simple configuration and reduced wiring method for a cost-effective solution for motion applications utilizing multiple single axes. With this new concept of direct plug-in modules, the amount of space used and the amount of wiring required is greatly reduced from traditional terminal board connections.
-
Product
PXI Precision Resistor Module 9-Channel, 2 to 52.4k
40-297-033
Programmable Resistor Modules
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
2-Ch Power Input With 4-Ch Digital Input EtherCAT Slice IO Module
AMAX-5001
-
Rated Voltage: 24VDC (± 20%)Dual Power Input: SupportedMax Current on Bus: 2ADiagnosis Function: Over/under voltage for input 1&2, Over current output on bus.
-
Product
Encoder
SFT3236S/SFT3244S
-
Hangzhou Softel Optic Co., Ltd.
SFT3236S/SFT3244S Multi-Channel encoder is a professional HD/SD audio & video encoding device. It has 16/24 HDMI inputs with very 8 HDMI ports share one encoder module with each module supporting 1*MPTS and 8*SPTS output. Its high integration and cost effective design makes the device widely used in varieties of digital distribution systems such as cable TV digital head-end, digital TV broadcasting etc.
-
Product
NI TB-2643B Terminal Block for NI 2532B as 1-Wire Dual 4x64 Matrix or 2-Wire 4×64 Matrix topology With Column Protection Resistors
782385-08
Terminal Block
The TB-2643B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 4x64 or 1-wire dual 4x64 matrix. You can directly connect the TB-2643B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2643B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
Industrial Automation & I/O
-
Advantech offers versatile I/O and automation devices from sensor modules, add-on DAQ cards or portable modules, remote I/O and wireless I/O devices, to IoT I/O gateways, RTUs, embedded automation computers, HMIs and software tools, which not only satisfy data acquisition, measurement, control, and communication needs but also allows cloud integration for wider area data management systems.
-
Product
2 Port T1/E1/PRI + 4 Port FXS PSTN
CH-4FXS-MOD-2PRI
-
One of the most feature rich PSTN simulator on the market. Unit has 4 analog phone lines (FXS) making it a perfect tool for testing VoIP gateways, IVR, V.90 modems, RAS servers, audio conference bridges or anything that requires analog phone lines. 2 port T1/E1/PRI module provides non-blocking switching among FXS ports and any of T1/E1/PRI B-channels or Time slots.
-
Product
Analog Output Module, 16-bit D/A
IP231
-
The IP231 outputs analog voltage signals to drive up to 16 devices. When used with a carrier that holds four IP modules, up to 64 voltage outputs can be obtained from a single card cage slot.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors
42-852A-518-M62.5
Multiplexer Module
The 40/42-852A-518-M62.5 is a PXI/PXIe 8-channel multiplexer with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-031-HI
-
The 40-230-031-HI (PXI) and 42-230-031-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 13.6kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
VPX 3U 1 Slot Chassis
HAWK
-
Combined with our IGUANA OpenVPX 3U switch module or Juniper Networks LN-1000 rugged router the HAWK is a very small but fully ruggedized networking platform. Combined with our 3U VPX Intel I7 CPU module it can be configured to meet various demands
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-140-HI
-
The 40-230-140-HI (PXI) and 42-230-140-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4Ω and 102kΩ with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Multi-Mode, 62.5/125 Fiber, ST Connectors
40-855A-522-M
Multiplexer Module
The 40/42-855A-522-M is a PXI/PXIe dual 2-channel multiplexer with ST connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Micro-Ohmmeters
RMO-A Series
-
The RMO-A is a portable micro-ohmmeter designed for contact resistance measurements of switchgear during manufacturing, commissioning and maintenance stages. This micro-ohmmeter is widely used by medium and high-voltage circuit breakers manufacturers. Other typical applications are testing of disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. It accurately measures not only in factory environments but also in high-induction fields and substationsThe RMO-A series contains 6 models, rated from 100 A (RMO100A) to 600 A (RMO600A). The RMO500A (formerly CPM500) is our best seller, with 500 A ripple-free current and weighs only 8 kg.Although placed in a very portable and lightweight metal housing, RMO-A micro-ohmmeters have very high output power capabilities. They can generate 600 A test current continuously for up to 20 s. You can test with current up to 100 A without rest time. High output voltage enables a wider measurement range at the highest test currents, as well as the use of thinner/longer test cables. For testing with 100 A, 20 m test leads can be provided with only 16 mm2 cross-section.RMO-A micro-ohmmeter generates a true DC ripple-free (less than 1 %) current with automatically regulated test ramps. During a test, the RMO-A ramps up with increasing current before measuring and decreasing current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.An additional option is a built-in High Precision module suitable for measurement of very low resistances, ranges from 1 to 30 µΩ, with 0,01 µΩ resolution.These instruments can store up to 500 measurements in internal memory. A built-in thermal printer is available as an option.Our free DV Win software communicates with the RMO-A micro-ohmmeters via USB or RS232 interface. It allows you to run the test remotely from PC, as well as to download test results, analyze and generate fully configurable test reports.
-
Product
FPGA Module
NM-FMC
-
The new development of the Informtest holding, the NM-FMC mezzanine module, is a convenient means by which users can independently implement their own algorithms for receiving, transmitting and digital processing of information at the hardware level. The module contains an Altera FPGA of the Stratix III family, a clock generation unit, 8 GB DDR3 memory and a 160-pin LPC connector for connecting FMC mezzanines.
-
Product
LXI High Voltage Switching - 8-Bank, 1-Pole, 4:1 Multiplexer Plugin Module
65-231-914
Multiplexer Module
The 65-231-914 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 67 GHz, 50 Ω, SMA-1.85, Failsafe
42-780B-571
Relay
The 40-780B-571 (PXI) and 42-780B-571 (PXIe) are single failsafe SPDT 67 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
High-Density Matrix Switch Card
1260-43
Matrix Switch Module
The Astronics 1260-43 is a high-density matrix switch card. Each module consists of three 8x24 single-wire matrices, which are interconnected via a 10-lane, single-wire bus. On-board configuration relays allow software control of the matrix configuration.
-
Product
Optical Spectrum Analyzer Module Specification
CA92001B
-
UCINSTRUMENTS CA92001B C band optical spectrum analyzer module is a spectral engine for Process Analytical Technology applications. The OSA module acts as a stand-alone spectral engine, imaging and measuring a wide range of vapors, liquids and solids through transmission and diffuse reflection in a rapid non-destructive process. Leveraging our proprietary Micro-Optic technology, UC INSTRUMENTS’ C band OSA module features the following characteristics: (1) compact; (2) light-weight; (3) low power consumption; and (4) wide wavelength coverage. These characteristics of UC INSTRUMENTS’ compact OSA engines are suitable for a variety of handheld, portable or bench-top OSA/spectrometer applications. Equipped with a state-of-the-art internal wavelength reference, the OSA module is capable of precisely measuring optical spectrum. Because it does not require an expensive InGaAs detector array, the compact OSA module is a cost-effective alternative to other grating-based OSA/spectrometer engines. The OSA communicates with a PC or an instrument motherboard via an USB interface. UCINSTRUMENTS’ OSA module platform can be installed or co-packaged into existing NIR OSA/spectrometers as a cost-efficient alternative to other scanning optical engines.
-
Product
200-Pin LFH Connector Block, Male
92-965-200-M
LFH Male Connector Block
Suitable for use on the front of PXI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximize copper cross sectional area and insulation properties. Users should make their own cable strain relief arrangements and ensure that appropriate electrical safety precautions are observed.
-
Product
PID Testing Equipment
-
The potential induced degradation (PID) is addressed with the standard IEC TS 62804-1. The standard defines two methods that enable analyzing occurring PID effects in a specific PV module type. PSE AG offers the necessary equipment for the test in a climate chamber. The test equipment can work with any climate chamber on the market and is delivered turnkey. It comes with all necessary equipment, high voltage power sources, sensors, data acquisition and software.
