Evaluation Boards
-
Product
3U PXI Express Board
SMT703
-
Sundance Multiprocessor Technology Ltd.
The SMT703 is built around a user programmable FPGA architecture that features the latest Xilinx Virtex 5 FPGAs. It is supported with two WiMAX RF transceivers that in turn are supported with a mixed signal front-end that integrates dual 12-bit ADCs and dual 12-bit DACs.
-
Product
VMEbus board
IIB-429--VME-4C
-
The IIB-429-VME-4C provides 16 ARINC-429 compatible channels (8 receive and 8 transmit) at any rate between 12.5 and 100 kbps. Because the IIB-429-VME-4C is built upon a flexible platform, user function can be implemented almost without restriction, making this product flexible and user-friendly. This VMEbus board has a 6U form factor. This VME unit is also available in a 3U form factor, as IIB-429-VME.
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, RS-422 Inputs
APCIE-1711-5V-I
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many differentuser applications to be quickly and easily developed and reconfigured as further requirements arise. Thanks to the FPGA board structure, further counting applications canbe realised through software adaptation.
-
Product
Signal Processor Board
MS 1532
-
- Frequency coverage from 5 kHz to 30 MHz in 1-Hz steps- High dynamic range: +30 dBm 3rd-order intercept typical- Digital filtering provides 58 IFBWs from 56 Hz to 8.0 kHz with exceptional shape factors- AM, Synchronous AM, FM, CW, USB, LSB & ISB detection modes standard- Tunable notch filter- Fast, flexible scanning with 100 memory channels- Large readable LED displays & user-friendly controls- Noise blanking & pass band tuning- Internal switchable preamplifier & attenuator- Operator-selectable RS-232, RS-485, or- RS-422 remote control- Viretx 5 FPGA based design (Two virtex for image processing)- LPC2468 ARM 7 Processor based design- MIL1553B and RS485 Interface- Two High speed 14 bit ADC (125MSPS) for I & Q Sampling- Direct sampling 2-30MHz- Audio CODEC- Conduction Cooled Board
-
Product
6U VPX UltraScale™ FPGA board with FMC+ sites
IC-FEP-VPX6e
-
Based on the latest Xilinx Kintex UltraScale™20nm FPGA, the IC-FEP-VPX6e is a 6U OpenVPX Front-End Processor (FEP) optimized for applications requiring DSP intensive processing in highly constrained environments.
-
Product
Multipurpose Debug Board
DB40-HPC Debug Module
-
The DB40-HPC Debug Card is designed for debugging of COM-HPC modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
-
Product
Shelf Manager Carrier/Mezzanine Board fix-mounted for CompactPCI
064-754
-
Set of Shelf manager mezzanine board installed on the fix mounted carrier board. The fix mounted carrier board provides all interfaces via headers for easy access and can be used directly inside of your system platform.
-
Product
14-bit 16 Concurrent Channel 65MSPS A/D board
AD14-65Mx16AVE
-
14-bit 16-concurrent channel 65MSPS A/D board for demanding large-system uses, where signals on multiple time-aligned channels need to be observed with high SNR, such as RADAR, nuclear instrumentation, ultrasound, medical imaging, spectroscopy, communications systems, RF component and antenna testing and other critical applications. An on-board low-jitter LMX2581-based RF synthesizer allows any A/D sampling rate between 20MSPS and 65MSPS to be specified in software. A second on-board LMX2581 with synchronized reference can be optionally used to output four stimulus clocks on SMA connectors that can be vectored to any combination of 4 external transmitters, microwave pulse generators, laser modulators, and other devices.
-
Product
PCIe Board
Solar Express 125 (SE125)
-
Sundance Multiprocessor Technology Ltd.
SE125 is a low profile, 8 lanes PCIe card powered by the Xilinx Zynq Utrascale+ MPSOC (XCZU7EV-2FFVC1156E / XCZU7EG/ XCZU11EG / XCZU7CG ). When XZU7EV is populated, it is capable of video decoding/encoding, up to 8K resolution, targeting Data Center video streaming applications and with 11EG it can be a network accelerator card.
-
Product
CableEye® HV-Rated QuickMount™ Housing for CAMI Connector Boards
CBH2
-
CAMI Research Inc. (Acton, MA) has released a High-Voltage (HV)-rated QuickMount housing (CBH2) for its CableEye® automation-ready, cable and wire harness testing systems. As a free-standing, quick-release board fixture, it allows users to connect CAMI’s test interface boards to the 64-pin headers of any expansion module - even at some distance. The housing may be used with any CableEye model and is rated to 2100 Vdc / 1500 Vac.
-
Product
CableEye 4-Wire Calibration Verification Board | Cable & Harness Testers
CB52
-
The CB52 is intended for periodic calibration verification of the Kelvin 4-wire resistance measurement module – an optional, add-on module that may be purchased with any new hipot system, or added to an existing high voltage tester as an upgrade.
-
Product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
-
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
Product
4K MIPI NVIDIA® Jetson TX2/TX1 Camera Board
E-CAM131_CUTX2
-
e-CAM131_CUTX2 - 13MP Jetson TX2/TX1 camera board is a 4-lane MIPI CSI-2 camera solution for NVIDIA® Jetson TX2/TX1 developer kit. This camera is based on 1/3.2" AR1335 CMOS image sensor with advanced 1.1µm pixel BSI technology from ON Semiconductor® and an integrated high-performance image signal processor (ISP) that performs all the Auto functions (Auto White Balance, Auto Exposure control). It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
Product
PCIe/104 OneBank FPGA I/O Board
EMC²-7A100
-
Sundance Multiprocessor Technology Ltd.
The EMC2-7A100 can use commercial, industrial or automotive graded Artix-7 FPGAs and is complimented with 1Gbyte of DDR3 local storage, 32Mbytes of Flash memory for storage/configurations and has 68x free differential I/O pins which are routed to a VITA57.1 FMC-LPC high-speed connector for bespoke interfaces.
-
Product
ANSI X3.28 Interface Board
Model 4804B-7
-
* F30145 firmware converts printable ASCII character strings into the ANSI X3.28 serial protocol.* User selectable single-ended RS-232 and differential RS-422/RS-485 serial signals.* Can be used to replace obsolete ICS 4814 Interfaces.* Connect to the rear panel with a GPIB Flat-ribbon cable or with a GPIB Connector/Address Switch Cable.* Runs on 5 Vdc regulated or 5.5 to 15 V unregulated power.
-
Product
Alchitry Au FPGA Development Board (Xilinx Artix 7)
-
The Alchitry Au is the "gold" standard for FPGA development boards and it's possibly one of the strongest boards of its type on the market. FPGAs, or Field-Programmable Gate Arrays, are an advanced development board type for engineers and hobbyists alike to experience the next step in programming with electronics. The Au continues the trend of more affordable and increasingly powerful FPGA boards arriving each year. This board is a fantastic starting point into the world of FPGAs and the heart of your next project. Finally, now that this board is built by SparkFun, we added a Qwiic connector for easy I2C integration!
-
Product
16-CH Discrete Input 16-CH Discrete Output Daughter Board Module
HSL-DI16DO16-DB-NN
-
- Slave ID consumption: 1 16-CH NPN sinking type sensor inputs or dry contact and 16-CH - NPN sinking type outputs- Photo couple isolation voltage: 2500Vrms- Input impedance: 4.7KΩ- Input current: ??10mA(Max), ??12.5mA(Peak)- Input voltage: ??40V (Max)- Output switching capacity:300mA/ch at 24VDC- Terminal Base:HSL-TB64 or HSL-TB32-DIN- LED indicator: Power, Link and I/O status
-
Product
PC/104 OneBank Board
EMC2-SoM3-100
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-SoM3-100 to be added to robust and rugged installations for various commercial, medical, industrial and military uses and to enable more versatility the EMC²-SoM3-100 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
Product
THRU HOLE BARE AND LOADED BOARD TEST PROBES
SERIES 93
-
ElectricalMAXIMUM CURRENT: 7 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS mean
-
Product
I/O Board With Two COM, Four USB 2.0 And Audio For PICO312, PICO313, PICO511, PICO512
AX93A09
-
*Specification: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 2.0, 1 x Audio (MIC-in/Line-out), 1 x Power-on, 1 x Reset, 2 x LED*Dimensions: 118 x 29 mm*Compliant products: PICO312, PICO313, PICO511, PICO512
-
Product
PXI Express High Speed Optical FPGA Board
HSS-8324
-
The Conduant HSS-8324 Optical FPGA board provides the user with a hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PXI Express (PXIe) interface and its 24-lane optical interface. The PXIe interface provides a theoretical maximum throughput of 8GB/s (simultaneous in and out).
-
Product
Single Board Computers
EPX-C414
-
WINSYSTEMS’ EPX-C414 is an EPIC-compatible single board computer using Intel®’s Bay Trail E3845 or E3825 processor. Its rugged design and extended operational temperature make it a great fit for industrial IoT applications and embedded systems in the industrial control, transportation, Mil/COTS, and energy markets
-
Product
Serial to Relay Interface Boards
Model 2364 OEM
-
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Serial interface header includes RS-232 and RS-485 signals. * GPIB interface header includes GPIB address switch input signals.* Includes 50-pin mating relay connector and serial header connector.* Optional 115750 Terminal Board for easy connections without soldering.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel.
-
Product
Dynamic Test Board Vehicle Simulator
DTB
-
The Dynamic Test Board vehicle simulator range enhances functional testing by allowing greater test depth before the prototyping stage.
-
Product
Digital I/O Board, 32 Isolated I/O Channels, 24 V
PA1500
-
*16 input channels 24 V, incl. 14 interruptible*16 output channels, 24 V, 500 mA Optical isolation 1000 V*Input and output filters*Watchdog*3 timers/counters
-
Product
Synchro/Resolver Conversion & Simulation PMC boards
-
Versatile, rugged, and time saving Synchro/Resolver conversion and simulation PMC boards featuring multiple high accuracy, independent channels and easy programmability, to provide a highly accurate and convenient method to test and simulate positioning systems in lab and embedded environments. The SB-3642 conversion and SB-3644 simulation boards’ versatility and ruggedness enable them to be used first in the lab, and then be readily designed into embedded applications, just by the switch of a carrier card.
-
Product
Isolated Programmable Multifunction Counter Board
APCI-1710-5V-I
-
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
Product
PXI Express Board Virtex-5 ADC Module
SMT790
-
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
Product
Four Channel Relay Board for Power Supply Isolation
FXA-113 PSU Relay 4CH
Power Supply
The FXA-113 is a four-channel relay board designed as an output disconnect option for laboratory power supplies. Especially in ICT applications it’s important, that the power supply is completely isolated from the DUT during measurements. Therefor each channel features two high current relays for the power path and two reed relays for the sense path. All four channels are equipped with a status led and can be switched independently. In addition, it is delivered with an installed DIN rail carrier.
