Optical Sensors
Detect and measure light.
-
Product
Medical Sensors
-
The pressure sensors listed below are available in a wide range of shapes, sizes, pressure ranges, and resolutions.
-
Product
Sensors
2D Fiber Probe
-
Smallest and most accurate probe for 2D evaluations world-wideMechanical fiber sensor with optical evaluation from image processorTransmitted light and self illumination modeLowest contact force of 1 µNSphere diameters down to 25 µmControl and evaluation software for fully automatic measurements
-
-
Product
RMS Averaging Vibration Sensor
SQ-SVS
-
The vibration sensor module performs calibrated averaging (root mean squared) vibration measurement with analog voltage and digital serial outputs. Because acceleration signals are extremely fast by nature, they require high speed sampling and computationally intensive processing to measure.
-
Product
RS422 Mode SI-module With Optical Isolation And RTS/CTS
MX422-PEP
-
RS422 mode SI-module with optical isolation and RTS/CTS
-
Product
Optical signal transmission
Digital
-
The fibre optic cable are used to transmit digital signals from the device under test under EFT/burst interference.
-
-
Product
Hall Effect Sensor
907 XP (Explosion Proof)
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
-
Product
QTI Sensor
555-27401
-
The QTI Sensor is a close-proximity infrared emitter/receiver that is able to differentiate between a dark surface) with low IR reflectivity) and a light surface (with high IR reflectivity). These little sensors can be very handy for line following, maze navigation, or sensing the outer rim of a SumoBot ring. Wiring options allow it to be used digitally for fast black/white line following, or as an analog sensor to detect different shades of gray. A daylight filter is built into the sensor.
-
Product
Optical Power Meter
TL-520
-
TL520 Mini-Designed Optical Power Meter is a self-developed test instrument which is widely used for installation, operation and maintenance of fiber-optic network. TL520 can test optical power within the range of 800~1700nm wave length. There are 850nm, 1300nm, 1310nm, 1490nm, 1550nm, 1625nm, six calibrated wavelength.
-
Product
LilyPad Temperature Sensor
-
Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature. Detect physical touch based on body heat and ambient conditions with this small sensor.
-
Product
Sensor Scene Modeling and Analysis Software
INSSITE
-
INSSITE is a sensor scene modeling and analysis environment. Different sensor types and modalities, spanning radar (synthetic aperture radar [SAR], ground moving target indicator [GMTI], detection and ranging, radio frequency [RF] communications), visible/infrared (passive electro-optical/infrared [EO/IR], laser radar [ladar], thermal IR), can be evaluated against high fidelity scenarios constructed by the user.
-
Product
Optical Monitoring
-
Perform OSNR monitoring, valid channel detection, and center wavelength measurement of signals with arbitrary modulation formats.
-
Product
Optical Transmitter
ST1550E
-
Hangzhou Softel Optic Co., Ltd.
SFT1550E is a high performance external modulation 1550nm Optic transmitter with a high quality LiNbO3 external modulator and a high power, narrow bandwidth, low noise DFB laser. It adopts a series of unique innovation technique to reach the excellent system control. With 47~862Mhz bandwidth, CNR≥53dB, CTB≤-65dB, CSO≤-65dB, SBS: 13, 16, 18adjustable, it can make CA TV network transmit video, audio and data with high performance. The machine can is equipped with perfect RS232 communication interface, SNMP network management and 1+1 backup power supply .
-
Product
Fiber Optic Power Meters and Fault Locators
-
Fiber optic communication systems require the right tools to commission new links and to troubleshoot existing links. Fluke Networks has a wide range of Fiber Optic testing products to help certify that power losses are within standards and to troubleshoot broken and high loss links on single mode and multimode fiber. Fluke Network fiber optic tools are designed to be rugged and reliable, and to get the job done.
-
Product
Split type Pulse Current Sensor
CTF-05T
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For detecting current pulse with open collector output (for power pulse)
-
Product
Atmospheric Pressure Sensor
SBS-02A
-
Provides: Altitude and rate of climb/descent data. Range: 500-1100hPA or 162.4-16,000 feet (-50 to +5500 meters). Weight: 0.10 oz. (2.7 g)
-
Product
Wafer Mapping Sensor
M-DW1
-
Panasonic Industrial Devices Sales Company of America
To provide better safety and improved sensing accuracy, Panasonic studied the requirements for future Wafer Mapping Sensors to ultimately develop the LED Beam Reflective Type Wafer Mapping Sensor, M-DW1. This Sensor uses LEDs as a light source for safe operation and a 2-segment receiving element for higher accuracy in wafer detection.
-
Product
Percent Oxygen Sensors
-
At Process Sensing Technologies (PST), we offer replacement electrochemical oxygen sensors compatible with major fixed and portable oxygen analyzers in challenging industrial environments. Tailor your solution with our versatile housing options, allowing you to specify either a 2-ring or connector design.
-
Product
Plano Optical Substrate Fabrication
-
Keysight has the technology and expertise to fulfill all your requirements for precision plano substrates up to 300mm:
-
Product
Portable heat flux sensor, with read-out unit
HF03 / LI19
-
Hukseflux Thermal Sensors B.V.
The HF03 is a heat flux sensor that can be used in mobile applications. It is combined with LI19, a high accuracy hand-held read-out unit that can be used both for mobile measurements and as an amplifier directly connected to a PC. The combination HF03 / LI19 is typically used to study heat flux levels around flares and fires, and to calibrate flare radiation monitors / flare heat flux sensors.
-
Product
PXI/PXIe MEMS Optical MUX, Dual 2-Channel, Single-Mode
40-855A-322
Multiplexer Module
The 40/42-855A-322 is a PXI/PXIe dual 2-channel multiplexer with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Light-Transmitting/-Receiving Devices for Optical Communication Systems
-
Sumitomo Electric Industries, Ltd.
Various light-transmitting/-receiving devices support the foundation of optical communication systems. The portfolio includes semiconductor lasers and photodiodes for optical transceiver modules and board level design, as well as wavelength-tunable lasers and optical receivers for optical coherent communication devices in the backbone systems.
-
Product
Pressure Sensors For Blast Testing
-
Pressure sensors with quartz, ceramic and tourmaline sensing elements are used for a wide variety of shock wave, blast and explosive testing. All of these applications require high frequency response and durability, ability to drive long cables and operate in adverse environments.
-
Product
Precision Optical Assemblies & Systems
-
Optical assemblies play a critical role in the function of optical systems. Our team has decades of experience developing optical products across a wide variety of challenging applications from medical imaging to space communications. We employ our battle-hardened design and development processes to move from spec to prototypes quickly, and deliver it right the first time with high yield. We maintain control on the entire project from incoming inspection of material to every element of the manufacturing process. Our well-established supply chain provides you with cost-effective flexibility to deliver essential equipment when you need it.
-
Product
Laser and Optics Case
E1734A
-
The E1734A is a heavy duty transport and storage case which houses a basic 5530 Laser Calibration System plus additional space for other components (except tripod and rotary measurement kit). The case has integrated wheels and handle for ease of moving around. Provision for padlocks for added security is available.
-
Product
Optical Lattice Clock
-
Our strontium lattice clock project aims to create the world’s first commercially available fully integrated optical frequency atomic clock. The clock will be compact, transportable, easy to use and based on optical lattice technology enabled by the SolsTiS. The strontium lattice clock will achieve frequency uncertainties below 10-17, a level unprecedented on the global market.
-
Product
Fiber optic active antennas / field probes
EFS-105
-
The EFS-105 is the first in a family of fiber-optic active antennas & E-field probes. The field distortion caused by the probe head is nearly zero due to the exceptionally small probe head and the all-optical signal transmission and power supply. This gives an invaluable advantage for near field measurements and measurements close to metallic parts.
-
Product
LED Color Sensor
Smart FINN Bright
-
LED applications have evolved from simple status indications to extremely bright lighting for commercial, industrial and military applications. The intensities of these bright LEDs are beyond the capability of the human eye to withstand, let alone be able to discriminate for color. Much like the human eye with sunglasses, we are able to shade our FINN sensors in order to provide accurate color and intensity measurements.
-
Product
Oxygen Sensor
KS60006
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
