- Pickering Interfaces Inc.
product
PXI Dual 8x4 Matrix Module, 2-pole 2A,60W
40-515-002
The 40-515/516/517 2 Amp, 2-Pole Matrix Modules form part of the System 40 PXI ProgrammableSwitching system. Each module consists of a matrix of 64 2-pole electro-mechanicalrelays under the control of a PXI/PCI interface.These modules are designed for switching medium voltage/power signals in test applicationswhere reed relays do not have sufficient rating. They are also suitable for telecomsapplications where send and return signals need to be switched simultaneously.
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
In-Circuit Test Fixtures
Every type of in-circuit test fixtures (wired, wireless, pneumatic, vacuum) for all major tester brands.
-
product
USB PD Test System
6050
Single Output USB PD USB PD basic version:the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
product
7-Pole Test Switch Protectors
6442 & 6442-C
With safety always being a concern while working with electrical boxes, you can depend on TESCO’s Test Switch Protectors (Catalog No. 6442 & 6442-C) to alleviate any uncertainty. This was developed to provide temporary protection of the test switch and to address the rising concern that the terminals of the test switch are exposed while you’re working in the box. The switch protector can prevent incidental contact with live terminals or contact with tools. TESCO’s Test Switch Protectors are ...show more -
product
ARINC 429 USB & LAN Test & Simulation Module
UXI-429
Avionics Interface Technologies
8 Channel (4Tx/4Rx) & 16 Channel (8 Tx/8 Rx) models available - Programmable Tx channel output amplitude - Programmable high/low speed operation - Concurrent operation of all Tx/Rx channels at high speed rates - Full error injection & detection - Rate-oriented label transmission - Label selective trigger for capture/filtering - Real-time recording & post analysis of multiple channels - Physical Bus Replay - Onboard IRIG-B time code encoder/decoder for Synchronization - Time Synchronization to IEEE 1588 via Ethernet LAN port - 10 Discrete I/O Interfaces (5 Outputs / 5 Inputs)
-
product
Imaging Gauge Software Test System
The IMAGING GAUGETM quality analysis system was developed by APPLIED IMAGE to address the growing need to standardize the evaluation of camera image quality. The system includes a Test Chart manufactured using our ACCUedge® technology, along with unique Image Analysis Software, used together to analyze the quality of the imaging system, and then provide a summary report on the various image quality metrics. Our goal is to provide a simple to use, unique image analysis system, that can be utilized by R&D, scientists, system integrators, technicians and field operators to evaluate the camera quality or imaging system.
-
product
Preheating Test Setup for Hair Straightener
SCR ELEKTRONIKS have developed "60 Stations Preheating Test Setup for Hair Straightener“ for Testing of Hair Straightener. It consists of Adjustable Constant Voltage source, Digital Timer, Digital Voltmeter, Digital Timer for carrying out Heating Test of Hair Straightener. It has got the capacity to check hair straightener that require test current 28 A at different Test Voltages.
-
product
Impulse Test Equipment
mpulse test equipment for testing of low-voltage rotator windings.The equipment is composed of a surge impulse generator circuit, phase selector unit (selection between U, V and W), and waveform recorder circuit to provide a differential method type of impulse testing instrument.
-
product
Hign Speed Bare Board Test System By Non-Contact Test Technologies
SX-750SUPERⅣ
Suitable for a wide range of applications. Can be connected to a wide range of machines: from hand press to reel mechanism and in-line mechanism. We offer docking with our customers own machines. Compact main tester simplifies integration via installation inside a mechanism. If requested, we will perform a study to decide which functions should be added.
-
product
Snap Button Pull Test Machine
UI-TX01
Snap Button Pull Test Machine is used to test pull strength of ornaments on garment, toy, footwear and others including button, bow and etc. Snap button pull test is a must-do test especially for Baby and children’s clothing and shoes. The test aims to use to button snap pull tester with suitable grips to pull the ornament to know if the ornament would be pulled off garment or not. The ornament falling off or broken button may cause infants or children the risk of ingestion. The button pull test methods includes 16CFR1500.51-53, ASTM PS79-96, ASTM F963, EN 71-1,M&S P115A and etc.
-
product
SMD Tweezer Capacitance Resistance Diode Tweezers Test Pen Multimeter SMD Meter
VA50372
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
SMD tweezer Capacitance Resistance Diode Tweezers Test Pen Multimeter SMD Meter VA503 SMD Components Identifier
-
product
Sensors Test Cells
Integrated MEMS
The best technical performance, cost optimization, one-shot factory integration.A single unit integrates the modules for the handling, contacting and complete testing of MEMS devices, including the physical stimulus for functional test, and the tri-temp thermal conditioning.
-
product
Test & Simulation Interface for PCI-X
PCI-X-C1760
Avionics Interface Technologies
HS1760/MIL-STD-1760E Test & Simulation Interface for PCI-X
-
product
Advanced Test Platform
980 12G
The Teledyne LeCroy quantumdata 980 12G-SDI Video Generator / Analyzer module supports video and audio functional testing of next gen broadcast monitors, conversion devices and sources up to 12G-SDI. The module is equipped with four (4)12G-SDI-capable output ports. The output ports can be aggregated for Dual link HD-SDI and Quad link 3G-SDI operation. A genlock input supporting both SD analog black burst and HD tri-level to sync the output clocks with a "house sync" but the module can also run o...show more -
product
Universal In-Line Test Platform
UniLine brings 20+ years of test & quality experience to your manufacturing floor and test automation delivers accurate results, without bias. By standardizing test, product quality improves as costs decrease. Equipment becomes understandable and manageable across departments and station support becomes simple.
-
product
Power Conversion Automated Test Platform
C8000
Chroma Systems Solutions, Inc.
Power conversion testing is our core competency. Chroma’s engineering delivers cost-effective automated test system and software platforms to fit your Design Validation Testing (DVT) requirements in the lab or High Speed Functional Testing in the production line. Built into each system are Chroma’s years of expertise, precision instrumentation, pre-written test libraries, and local program management with global support. From power conversion to battery to electrical safety, our test systems will maximize your time, improve your validation process, and increase your throughput.
-
product
MCB Tripping Current Characteristic Test Bench
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
product
Automatic Insulation Oil Dielectric(breakdown) Test
HDIIJ-80
HD Power Test Equipment Co.ltd
Automatic Insulation Oil Dielectric(breakdown) Tester is used to carry on power frequency dielectric break down test on the transformer oil, capacitor oil, electric device, insulation tool, electric manufacturer and etc. It adopts full auto digital microcomputer, which has the function of high accuracy, strong anti-interference ability and safe reliability
-
product
Temperature Humidity Vibration Combined Environmental Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Temperature Humidity Vibration Combined Test Chamber meets national standards and meets specific testing requirements. It is widely used in electrical and electronic products, automotive parts, materials, etc.
-
product
Optics Test Systems
Mobile Wedge Angle Sensor With Positioning System
Optik Elektronik Gerätetechnik GmbH
Mobile wedge angle sensor for determining the wedge angle and the radius of curvature of glass panes, eg windshields of automobiles, helicopters, airplanes or rail vehicles.
-
product
Database API
Woodcreeper
LXinstruments Woodcreeper provides a convenient database API for our MySQL test database. It allows manipulation of the database from within the test sequence, for instance when data from upstream process steps needs to be accessed. Third party test systems can also be easily linked to the LXinstruments test database. One license for Woodcreeper comes with the TSCOE4 system license; standalone licenses are also available.
-
product
PXI-2557, 2.5 GHz, 75 Ω, 8x1 PXI RF Multiplexer Switch Module
778572-57
2.5 GHz, 75 Ω, 8x1 PXI RF Multiplexer Switch Module—The PXI‑2557 is an RF signal multiplexer switch module. The higher channel count of the PXI‑2557 makes it ideal for test systems that require the switching of a large number of video RF signals, such as switching several video tuners under test to a single channel on the RF analyzer. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
RF Test Probes
With over 50 Tip-Styles, you can be certain we can help you find the right solution for your testing demands. And if we don’t offer a probe solution already in production, we will work together with you to develop a custom solution.
-
product
Multi-Modular Cable Tester
3PK-NT005N
Multi-modular cable tester is applied to quickly test by auto scanning most of modular cable, USOC 4 / USOC6 / USOC 8 terminating with RJ 45, RJ12, and RJ11 modular plug, wires continuity and miss-wiring.It can be also used for testing the cable is crossed pinning or straight through. Moreover, with the remote terminator, it can be further used in remote testing even the cable has been already installed.
-
product
Terminal Mechanical Strength Test
The terminal strength test is used to performed to determine whether the design of electrical terminals and their method of attachment can withstand mechanical stresses to which they will be subjected during installation or disassembly in equipment. These stresses must be withstood by the component without sustaining damage which would affect either the integrity of the terminals or the operation of the component part itself. Procedures are established in this method for testing, for example wir...show more -
product
Compliance Test Systems
LMG Test Suite
ZES ZIMMER Electronic Systems GmbH
The ZES ZIMMER test system LMG Test Suite tests in accordance with the currently valid version of EN 61000-3-2/-12 or EN 61000-3-3/-11 and also supports measurements per ECE R-10.4 Annex 11 (e.g. electromagnetic compatibility of vehicles). As a manufacturer of precision power measurement technology, we are represented on the international standards committee. As a result, changes in standards are immediately incorporated into our test systems.
-
product
Explosive Atmosphere Test
This test demonstrates that a part will not ignite while operating in an explosive ambient atmosphere. The tests are conducted at ground level pressure as well as reduced barometric pressures, in a closed explosion-proof chamber.
-
product
ARINC-429 Multi-Channel Test & Simulation Module for Excalibur 8000 Family of Carrier Boards
M8K429
The M8K429 is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 8000 family of carrier boards. The module supports up to five ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word. The receivers allow for filtering and multi-storage modes of Data Words....show more -
product
Large Range scales
ESK-Series
Napco Precision Instruments Co
Big country’s most high-precision electronic weighing scale, complete specifications, weighing speed, high precision, stable and reliable, simple operation, widely used in industrial measurement and cast-iron weights of the test.
-
product
Electro-optic Test Bench for IR Detectors
BIRD 210
Testing detectors requires the implementation of ultra-low noise driving electronics and presenting high quality optical stimuli to the detector under test. This meets all these requirements and allows to test any type of detector by easily implementing the detector’s driving signals and providing exhaustive and accurate measurement results.