-
product
Chroma LCR Meters
Chroma Systems Solutions, Inc.
Some of the key features to look for in an LCR meter (also known as an impedance meter) are: accuracy, test frequency, measured parameters, test voltage and test current. Additionally, an easy to understand display of test results and the ability to access and use these results has become increasingly important. Component testing often requires much more than simply a resistance, capacitance or inductance value at a given test frequency and stimulus voltage. An LCR meter or impedance meter must have the flexibility to provide multi-parameters over wide frequency and voltage ranges.
-
product
Benchtop with Drop-In Test System
600 Series Compact ATE Platform
The Circuit Check 600 Series Compact ATE Platform with built-in professional fixturing solves the uncertainty of repeatable results that are common with bench testing. With the 600 Series Compact ATE, test procedures can become automatic, with test steps and go/no-go limits easily programmable. Hand-probing is eliminated, replaced with accurate, repeatable tooling and reliable spring-loaded test probe fixturing.
-
product
Safety Shoe Electrical Resistance Tester
UI-FT06
Safety Shoe Electrical Resistance Tester is to test the electrical resistance of conductive footwear and antistatic footwear.
-
product
Circuit Breaker Test Systems
Crest has over a decade of experience of designing and manufacturing test systems for testing all the different kinds of switchgear and controlgear.
-
product
Debug Fixture
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-...show more -
product
Particle Impact Noise Detection (PIND) Test
This test detects the presence of free moving particulate contaminants within sealed cavity devices. This test is specifically directed toward relays and other devices where internal mechanism noise makes rejection exclusively by threshold level impractical. This test method also may be used prior to final sealing in the manufacturing sequence as a means of eliminating loose particles from the interior of the device.
-
product
Test Systems
Ball Systems delivers best-in-class automated testing systems, software programming, integrated manufacturing systems, and industrial engineered solutions. Our team has former corporate test engineers, quality assurance engineers, industrial engineers, and test managers who have decades of experience to assist customers in meeting their automated test challenges by offering:
-
product
Walk in Chamber for Rapid Rate Temperature / Humidity Test
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Walk in Chamber for Rapid Rate Temperature / Humidity Test Relevant standards requirement:Temperature shockTest Object: Battery storage pack or system.Li-ion battery pack or system placed in (-40±2)℃~(85±2)℃ alternation temperature, the conversion time of two extreme temperatures is less than 30 minutes. Place the test objects into each extreme temperature keep 8h, test 5 cycles.Observe for 2 hours under the room temperature after testing,Humidity & Temperature CyclingTest Object: Battery storage pack or system.Refer the GB/T2423.4 Test Db, variable refer the Graph 4,the highest temperature is +80℃,5 cycles. Observe for 2h under the room temperature.
-
product
Turnkey Boundary Scan Solutions
TestGenie
TestGenie is a low-cost boundary-scan solution for those companies that have a genuine requirement for JTAG testing, but have difficulty absorbing the tool costs or assigning the resources required to implement the test technology into their development or production processes. TestGenie allows customers to use full-featured versions of Corelis ScanExpress products at a fraction of the cost.Once you’ve selected boundary-scan as a practical solution, the second biggest decision is whether you want to do the test development yourself or have a third party do it. The decision should not be considered lightly as there are advantages and disadvantages to each.
-
product
Power Products
With the advancing development and expansion of renewable energies, modern electrical equipment must be developed, manufactured and tested according to nationally as well as internationally valid standards. This requires powerful power supplies & test equipment.Thanks to our extensive product portfolio with the full range of devices, we are able to cover all relevant areas of application. Our range includes standardised desktop units for single workstations up to individually and customised modified special solutions in 19” racks in the megawatt range with voltages up to 2.25 kV.
-
product
4-Quadrant General-Purpose Source/Measure Unit, ±20 V, ±1 A Or ±6 V, ±3 A, 20 W
N6784A
The Keysight N6784A is a source/measure unit (SMU) designed for general-purpose precision sourcing and measurement. General-purpose applications can span many different industries and many different devices under test (DUTs). The N6784A SMU is a versatile tool designed to tackle many of these general-purpose applications. Its glitch-free operation ensures safe usage with the DUT during output and measurement range changes, even with capacitances of up to 150 µF. Its 4-quadrant operation enables ...show more -
product
MEMS And Sensor Test Solutions
Modular design based on standard handlers, high parallelism, ambient to automotive tri-temp handling.
-
product
5 kW and 10 kW RP7900 Series Regenerative Power System
RP7900 Series
The RP7900 Series regenerative power system is a family of 5 kW and 10 kW bi-directional, regenerative DC power supplies that reduces the cost of test with highly integrated capabilities. The regenerative capability enables the energy consumed to be put back onto the grid cleanly, saving costs from energy consumption and cooling, while not interfering with the grid. The RP7900 helps you overcome your toughest power test challenges by delivering industry-leading specifications and innovative features in an integrated solution for today's advanced high power automated test equipment (ATE)power testing needs. The RP7900 provides the fastest, most accurate, integrated regenerative power system.
-
product
Power-off Circuit Board Testing
Huntron® Trackers®
Adding diagnostic tools to enhance your circuit board test capabilities is an important part of any electronic repair environment.Huntron Tracker power-off circuit board test uses analog signature analysis to detect and isolate component faults on boards beyond power-on functional testing. By comparing Tracker signatures from a working circuit board to the signatures of a non-working board, you can troubleshoot down to the component level.
-
product
Signal And Image Processing Research
TPAC solutions are ideal for research in signal processing applied to ultrasound. You need to be able to access to any parameter, implement a particular algorithm, and access to any data during the acquisition or postprocessing phase. TPAC provides you all of these. It can be applied to studies in signal processing, image processing, beamforming, machine learning, etc… Thanks to TPAC’s open platforms, you will be able to freely set the ultrasonic sequences, record the raw data from your experime...show more -
product
Titan Data Acquisition
DAQ
Titan Data Acquisition (DAQ) Systems offer universal signal conditioning, low power consumption, convenient SD card storage, and easy-to-use software. Systems can be purchased as a complete test kit, including custom cables and accessories. Titan products are designed and built in the US.
-
product
Holiday Detector
VHD
Veer Electronics make Holiday Detector is capable to test various insulative coatings like Coal tar, Paint etc. It generates high Voltage DC for testing. When this Voltage is applied to the coated area and if pinhole or any defective point of coating is detected high voltage spark occurs on pipe or surface where we are testing. At the same time, an electronic Buzzer also beeps which gives Audio indication as well as Red colour Fault LED also glows as Visual indiction of fault.
-
product
Probe Series
CAPELLA Series
MPI Photonics Automation is the industry leading provider of turnkey test solutions for the LED / Mini LED manufacturing industry. With more than 10,000 MPI probers installed worldwide, the CAPELLA series of probers have a proven track record of superior performance and reliability. The CAPELLA series probers support electrical and optical characterization of all LED product types (Vertical chip, Lateral chip, Flip-chip) from wafer to packaged die level. Whether you need a high-performance, cost-effective or specialty prober system, MPI PA has the most comprehensive range of LED wafer/chip probers to meet your exacting requirements.
-
product
Imaging Automation
XImage
Whether you are a Microsoft Authorized Refurbisher, Microsoft Registered Refurbisher or just getting started in refurbishing, Erasure, Test and Re-Imaging are a must to get the most out of your assets. The problem is that until now, this required a big work force. One group to perform the testing and visual inspection, one group to perform erasure, someone to create and manage all your images and substantial knowledge on how to automate and deploy those images. Even with all of these bases covered, it can still be a complicated, time consuming task. Not to mention the fact that it is typically done in a separate process from data erasure, testing and auditing.
-
product
Combined High Voltage Test Set
is extensively used to measure AC and DC voltage of different electrical devices.
-
product
Transformer Tester
Kvtester Electronics Technology Co.,Ltd
High precision instrument for measuring characteristic parameters of transformer capacity, no-load and load. The instrument is a multi-function measuring instrument, which is equivalent to the usual two kinds of test instruments: the transformer capacity tester + transformer characteristic parameter tester. The utility model can precisely measure a series of power frequency parameters of a plurality of transformers, such as the capacity, the type, the no-load current, the no-load loss, the short circuit (load) loss and the impedance voltage.
-
product
Hydraulic Vertical Shock Test System
KRD10 series
KRD10 series full-automatic hydraulic shock test system is used to measure and determine the impact resistance of products or packaging, and to evaluate the reliability and structural integrity of products in a shock environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests to achieve the shock wave and impact energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
product
PCI-6123, 8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O DeviceMultifunction I/O Device
779409-01
8 AI (16-Bit, 500 kS/s/ch), 8 DIO, PCI Multifunction I/O Device - The PCI‑6123 is a simultaneous-sampling, multifunction DAQ device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6123 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6123 dimensions require chassis slots that can accommodate full-length PCI modules.
-
product
Compact Optical Environment Test Measurement System
Durability test with temperature, humidity and "sunlight"●Espec SH-241 small environmental tester combined with a solar simulator for durability testing under temperature, humidity and light environments●Software is also available.●Please inquire about the system configuration individually.
-
product
AC Fuel Flow Signal Generator
TA-100
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 s...show more -
product
Digital Display Auto Circuit Tester
1676
Peaceful Thriving Enterprise Co Ltd
This is a DC voltage tester with smart over-voltage protection and warning for vehicle repair. As electrical system for vehicle becomes more complex, the tester is able to test voltage value, identify DC polarity from different background light color, positive / negative sign, and over-voltage level indication. Moreover, the special designed probe is able to help user to hook, piercing, and probing the wires.
-
product
Portable Interface Unit
1553-USB-PIU
The 1553-USB-PIU is a Portable Interface Unit providing full MIL-STD-1553 test, simulation and bus analysis capability in a compact self-contained unit, to connect via a USB interface to suitable host systems. The unit provides support for all 1553A, 1553B, McAir and STANAG 3838 variants in a self contained battery operated unit, and is supplied with a matching power supply and battery charger unit for desk-top use. The 1553-USB-PIU supports concurrent Bus Controller (BC) and up to 31 Remote Ter...show more -
product
Laser Diode Testing
The low power series of burn-in and life test systems are designed to test the reliability of low power laser diodes up to 1 Amp in current. The modular design means they can test up to 2,048 lasers, however due to the flexibility of the system, it can be adapted to suit both low volume R&D environments and high volume production environments.
-
product
Probe Card
VC43™/VC43EAF™
VC43™/VC43EAF™ probe cards offer a larger format version of the popular VC20. In addition to saving time, another advantage of the modularity is the ability to leave the interface in place and simply install the VC43™ topside using Celadon’s twist and lock insertion tool which minimizes the possibility of triboelectric or interconnect issues that can occur during typical probe card changes. The VC43™ can be used for production parametric test, modeling, characterization, and wafer level reliabil...show more -
product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of t...show more