Fibre Channel
Data transfer interface with speeds up to 2 Gigabit per second that maps to common transport protocols, i.e. IP and SCSI.
-
Product
16 Channel Power PXI Multiplexer, 2 Pole
40-650-002
-
A 16 Channel Power Multiplexer, suitable for switching inductive/ capacitive loads up to 5A at 250VAC. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. It is suitable for applications requiring switching of either mains voltage or DC.
-
Product
NI-9436 , 120 VDC to 240 VDC/120 VAC to 240 VAC, 8 Channel (Sinking/Sourcing Input), 20 ms C Series Digital Module
784338-01
-
120 VDC to 240 VDC/120 VAC to 240 VAC, 8 Channel (Sinking/Sourcing Input), 20 ms C Series Digital Module - The NI‑9436 works with industrial, high-voltage logic levels and signals to connect directly to a wide array of industrial devices such as fans and motors. Each channel accepts signals from 120 VDC to 240 VDC and 120 VAC to 240 VAC; features transient overvoltage protection between the input channels and earth ground; channel to channel and channel to earth isolation up to 250 Vrms; and has an LED that indicates the status of each channel.
-
Product
Mixed Signal Oscilloscope - 1 GHz, 2 Analog Plus 16 Digital Channels
MSOX3102T
-
1 GHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
HandyScope HS5: 50 MS/s 250MHz BW, 2 Channel, USB Digital Storage Oscilloscope, 5MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
HS5-055XM-W5
-
The Handyscope HS5 is the first USB oscilloscope (USB powered) sampling at 50 MHz, with a 14 bits resolution and a 250 MHz bandwidth. This makes it possible to analyze very fast signals with very small amplitudes. The smallest distortions can be revealed due to the high resolution and bandwidth. Because of the deep memory (up to 64 MSamples on one channel), long record measurements are available for intermittent phenomena and Fast Fourier Transform calculations with over 32 million spectral lines can be performed. Using very fast FFT algorithms, an FFT with 1 million spectral lines can be performed within a second.
-
Product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4X.2230-X4
-
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Winding Resistance Meter 50Amps, 2 Channels
WR50-12
-
Raytech Digital Winding Resistance meter WR50-12 is the enhanced version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
Coarse Wavelength Division Multiplexer Mux & Demux Module 8 Channels and Express port, LC/PC Connector
SUN-CWDM
-
Guilin GLsun Science and Tech Group Co., LTD
Wavelength1260 ~ 1620 nmReturn Loss≥ 45 dBDirectivity≥ 50 dBConnectorLC/PCMax. Optical Power≤ 500 mWPDL≤ 0.15 dBRelative Humidity5%~ 95%Dimension100×80×10.5 mmOperating Temperature-10℃ to +70℃Storage Temperature-40℃ to +85℃
-
Product
16 SE Or 8 Diff. Input Channels, 4 Analog Current Output Channels, PCI Express
APCIE-3121-16-4C
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
WiFiScope WS5: 200 MS/s 250MHz BW, 2 Channel, Digital Storage Oscilloscope, 20MHz AWG, Spectrum Analyzer, Voltmeter, Transient Recorder
WS5-220XM-W5
-
TiePie engineering has introduced the WiFiScope series oscilloscopes. The new range WiFi oscilloscopes can be used via an ethernet connection (LAN, WiFi or WAN) but also still with a USB 2.0 / 3.0 connection. The built-in battery gives the WiFiScope the possibility to perform fully wireless measurements. Measurements can then be performed completely galvanically isolated, and over long distances. This wireless PC-based data acquisition instrument offers the user more possibilities for measurement applications.With a WAN connection, worldwide measurements can be performed. Specific knowledge on networks is not required. The Multi Channel software gives an overview of the available USB instruments and network instruments. Simply tick the instrument and measuring can start. The WiFi oscilloscope has the following advantages: fully wireless measurements via WiFi are performed (galvanically isolated) because of the built-in battery mobile measurements are possible, e.g. on transport systems and moving installations LAN and WAN data acquisition is available for long distance measurements continuous realtime highspeed data acquisition over both WiFi and LAN/WAN are available USB measurements for stand-alone applications and highspeed data acquisition up to 200MSa/s.
-
Product
20mhz 2 Channel Analog Oscilloscope
MOS-620CH
-
Shenzhen Chuangxin Instruments Co., Ltd.
20mhz 2 channel analog oscilloscope
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 3 Channels, 2.5 GS/s on 6 Channels, 1.23 GS/s on 12 Channels
DN6.225-12
-
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
1520W Single Channel 19", 1U, Rack Mounted DC Power Supply
T3PS40381P
-
1520W Single Channel 19", 1U, Rack Mounted DC Power Supply.
-
Product
General Purpose 4 Channel Optocoupler Board
-
A general purpose 4 channel optocoupler board using H11G2 optocouplers (see above schematic). Resistors, capacitors, and connections to terminal strip are made by customer to allow for complete flexibility.
-
Product
Infiniium UXR-Series Oscilloscope: 70 GHz, 4 Channels
UXR0704A
-
The UXR0704A is the 70 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope
-
Product
1 Channel, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTA
-
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 80 MS/s on 1 Channel (Single Ended) or 1 Channel (Differential)
M2P.5940-X4
-
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Infiniium MXR B-Series Oscilloscope: 6 GHz, 8 Channels
MXR608B
-
MXR608B Infiniium MXR-Series, 6 GHz on all 8 channels, option to integrate up to 8 instruments in one, hardware accelerated plotting, and fully upgradeable.
-
Product
10 Channel ADC FMC Module
ADCFN10-AC – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN10 is a ten channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-105MHz sampling speed based on ADI AD9650. Both AC and DC coupled input are supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
Product
Portable Oscilloscopes With Isolated Channels
-
Portable oscilloscope with 2 isolated channels, 600 V CAT III, 20 MHz bandwidth, 2 GS/s ETS, double 8,000-count multimeter with power measurements, 31-order harmonics with 40 to 450 Hz fund.,colour screen, USB.
-
Product
Oscilloscope 50 GHz, 4 Channels
UXR0504B
-
UXR0504B Infiniium UXR-Series is the 50 GHz, 4 channel, Infiniium UXR-Series real-time oscilloscope.
-
Product
12 A/D Channels (±25mA FSR); 24-bit Sigma-Delta
AD3
-
Module AD3 features 12 channels with up to 24-bit Sigma-Delta A/D converters for each individual channel. The maximum programmable, expected full-scale range input for the AD3 module is ±25 mA respectively. The A/D converters have programmable sample rates of up to 256 kHz.
-
Product
NI-9426, 24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module
780030-01
-
24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module - The NI‑9426 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels.
-
Product
PXIe 8 Bit High Speed Digitizer 5 GS/s on 1 Channel, 2.5 GS/s on 2 Channels, 1.25 GS/s on 4 Channels, 1.5 GHz Bandwidth
M4X.2234-X4
-
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Keysight 40/80 Channel Reed Multiplexer for 34980A
34923A
-
The Keysight 34923A module for the 34980A Multifunction Switch/Measure Unit is a high speed-multiplexer for general purpose scanning. It uses reed relays to achieve scan rates up to 500 channels-per-second. Use this module for high-throughput automated test applications as well as high-speed data logging and monitoring tasks.
-
Product
Oscilloscope, 350 MHz Bandwidth, 4 Input Channels, 50 Mpts/ch, 10 GS/s
HDO6034B
-
350 MHz, 4 Ch, 12 bits, 10 GS/s, 50 Mpts/Ch High Definition Oscilloscope with 15.6" Display.
-
Product
1 Channel 100 MHz Flash ADC
NIMbox DNAE
-
NIMbox DNAE - 1 channel 100 MHz flash ADC with 3 programmable TTL I/O ports, 2 channel DAC 100 MHz, 4 LE discriminators and 5 NIM or TTL I/O
-
Product
Data Acquisition DSP based 16 channel
-
The CPCI-AD8/16 module provides a 3U high performancedata acquisition subsystem. There are (8) eight or (16)sixteen 100/200 KSPS ADC’s for maximum performance.The Local DSP can be used to simply move data samplesto the CPCI bus or can provide processing functions suchas limit checking, FFT’s, digital filtering, etc. Software canbe downloaded to the DSP via the CPCI interface.Instrumentation amplifiers provide over-voltage protectionand gain on a per channel basis. The CPCI-AD8/16 canalso accept external scan and trigger signals from a frontpanel connector
-
Product
NI-6583, 200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO
781320-01
-
200 MHz, 32 Single-Ended and 16 LVDS Channels, Digital I/O Adapter Module for FlexRIO—The NI-6583 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 32 single-ended and 16 low-voltage differential signaling (LVDS) digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6583 can sample digital waveforms at up to 200 MHz. It includes support for selectable single-ended voltages from 1.2 to 3.3 Volts with 10 bit resolution and common LVDS voltages.
-
Product
Four Channel Arbitrary Waveform Generator 2.5GS/s 16Bit 1GS Mem 4CH 8 Markers AWG
P2584M
-
The Proteus P2584M, is a PXIe based, 2.5GS/s, four channel arbitrary waveform generator offering technologically advanced options and configurations such as, a dual channel 2.7GS/s digitizer with 9GHz bandwidth, to transform the instrument to an arbitrary waveform transceiver. The P2584M offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
Product
HandyScope HS6-DIFF With EMI & SafeGround: 1 GS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-1000XMEG-W5
-
The powerful capabilities of the WiFiScope HS6-DIFF-1000XMEG EMI analyzer give the user the possibility to quickly perform a good EMI compliance test. With this cost effective test, time and money are saved by avoiding extra visits to expensive EMC testing facilities. The supplied EMI probe set TP-EMI-HS6 contains three magnetic field (H field) probes and one electric field (E field) probe. The tripod ensures that the probes can be positioned properly at the object under test.
