RF Amplifiers
take low power RF signals and output RF signals that vary in the same way as the input signal, but with a raised amplitude.
See Also: Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers, Microwave Amplifiers, Rf Power Amplifiers
-
Product
PXI Dual 4 To 1 RF Multiplexer, 8GHz 50 Ohm SMA, Terminated
40-882A-002
-
The 40-881A-002 is a dual 50Ω 4 to 1 RF multiplexer with 8GHZ bandwidth.The 40-881A range of multiplexers have automatic termination of unused signals and are available as a single MUX in one PXI slot, a dual MUX in two PXI slots, or triple and quad MUXs in three slot PXI modules.
-
Product
LINEAR AMPLIFIERS
-
These amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance and fast response. The output is linear from DC up to megahertz range.
-
Product
PXI Dual 6 To 1 RF Multiplexer, 8GHz 50Ω SMA, Terminated
40-881A-002
-
The 40-881A-002 is a dual 6 to 1 50Ω RF multiplexer with 8GHz bandwidth and automatic termination of unused signal channels. It is available as a single or dual MUX in one and two PXI slots respectively.
-
Product
Handheld RF Spectrum Analyser
HSA-Q1
-
The HSA-Q1 is a fully integrated portable RF Spectrum Analyser designed specifically for professional countermeasures use. With a frequency range of 0 to 13.4 GHz and sweep time of just half a second, it offers unprecented performance in a truly handheld package.
-
Product
Dual 4 to 1 Terminated 50 600MHz PXI RF Multiplexer
40-761-002
-
This terminated dual 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
Composite 1×24 Video Distribution Amplifier Board
BL-VDA124-01
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
-
Product
75 Ohm BNC to BNC Cable Assembly
40-977-701-0.5m
-
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Peripheral Differential Amplifier
-
The Peripheral Differential Amplifier (PDA) module allows the simultaneous recording of differential bipolar high-ohmic external voltages, such as reference or pH meters. The PDA has 8 differential input channels, and it is stackable up to units with a total of 64 channels. The PDA module is powered from the grid via an adapter.
-
Product
"Standard" RF Low Pass Filters
-
Coaxial Dynamics "Standard" line of RF Low Pass Filters offers several models to choose from at CW power ratings of 100 watts and 200 watts. These filters cover operating frequencies from 88 MHz to 400 MHz with less than 0.5 dB insertion loss and attenuation levels of 40, 50 and 60 dB.
-
Product
RF Safety Monitoring
MVG EME Guard XS 40GHz
-
EME Guard XS 40 GHz has been specifically designed to cover the new 5G millimeter wave bands. This RF safety tool is important for keeping those working close to RF emitters safer. It is easy to use, continuously scanning electromagnetic waves, and alerts the user when acceptable pre-selected limits have been exceeded.
-
Product
Power Amplifiers
-
Precision Test makes two power amplifiers for use with our FSG series of hand held signal generators.
-
Product
RF Shield Box
CMW-Z10
-
The R&S®CMW-Z10 has excellent shielding effectiveness and superior coupling characteristics.The shield box can be used for frequencies up to 6 GHz.The antenna structure is optimized to enable excellent radio connections between the DUT and tester.The highly broadband spiral antenna allows a wide variety of applications.These outstanding features combined with modular options make the RF shield box indispensable for any radiocommunications tester.
-
Product
RF Power Controller (ALC)
310-010030-004
-
The serial controlled ALC module is used to set and monitor the output level of your fixed gain RF amplifier. The module is available for many bands between 800 MHz and 3 GHz, and is configured and calibrated to meet your requirements.
-
Product
Semiconductor Optical Amplifier
SOA
-
Amonics SOA is a polarization maintaining optical amplifier with high fiber-to-fiber gain. It is designed for transmitter applications to increase optical launch power to compensate for the loss of other optical devices. The benchtop version incorporates a user-friendly front panel housing a LCD monitor display, key switch, power control knob and optical connectors. RS232 computer interface is also equipped on the rear panel. 1MHz with 10ns pulse width intensity modulation is available. The OEM module version is an ideal building block for OEM system integration, especially in optical communication network and CATV applications. It requires only a single +5V power supply.
-
Product
PXI/PXIe RF Multiplexer, Dual 4-Channel, 3GHz, 50Ω, SMB
42-872A-002
-
The 40-872A-002 (PXI) and 42-872A-002 (PXIe) are 50 Ohm 4 to 1 PXI RF multiplexers with 2 banks in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
Ultrafast Laser Oscillators and Amplifiers
-
Coherent ultrafast lasers are designed and manufactured to provide the best performance, portfolio and support in the industry.
-
Product
Sound Source And Power Amplifier
-
Designed for acoustic application, with strong signal transmission capability and flexible measurement.
-
Product
Forced Air Cooled RF Coaxial Loads
86700 Series
-
The 86700 Series Forced Air Cooled RF Coaxial Loads are capable of dissipating up to 75 kW of CW RF power from DC Hz to 240 MHz with a VSWR of 1.15:1 or less. With this low reflection coefficient the loads are very useful for tuning transmitters.
-
Product
PXI/PXIe RF Matrix, 16x2, 100 MHz, 75 Ω SMB
42-728A-101
-
The 40-728A-101 (PXI) and 42-728A-101 (PXIe) are 16x2 75 Ω RF matrices with SMB connectors. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 75Ω, MCX
40-830A-103
-
The 40-830A-103 (PXI) and 42-830A-103 (PXIe) are 75Ω RF switches with 3 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-830A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
RF Hybrids
-
RF hybrids are used for combining multiple power line carrier (PLC) TX/RX units together onto one cable without causing interference between transmitters and receivers. They are also used for splitting PLC signals to go to two or three phases of a power line.
-
Product
PXI/PXIe RF Switch, Triple SPDT, 3GHz, 75Ω, SMB
40-830A-003
-
The 40-830A-003 (PXI) and 42-830A-003 (PXIe) are 75Ω RF switches with 3 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
Product
PXI/PXIe RF Matrix, 16x4, 300 MHz, 50 Ω, SMB
40-724-012
-
The 40-724-012 (PXI) and 42-724-012 (PXIe) are 16x4 RF matrix modules suitable for switching frequencies up to 300 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
Product
LTE/LTE-Advanced Analysis Using NI PXI RF Test Instruments
NI-RFmx LTE/LTE-Advanced
-
Highly optimized RF measurement experiencePerform physical layer analysis on LTE cellular signals including MODACC, ACPR, CHP, OBW, and SEMIncludes support for TDD, FDD, and LTE-Advanced signals specified in 3GPP standards release 12Simple access to advanced measurement parallelism
-
Product
Panel-mounted Power Amplifier For Network Simulators
PAV250Bi
-
PAV250Bi is one of the conventional voltage power amplifier model, which is specially designed for R&D of power system simulation.
-
Product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
-
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
-
Product
Amplifiers
-
Use our optical amplifiers to improve the signal-to-noise ratio (OSNR) and range performance of optical transmission systems.
-
Product
MS-M 3-Pin RF Cable Assembly 0.5m
40-979-503-0.5m-FU
-
The MS-M RF 3-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with PVC insulation and an attenuation of 1.08dB/m at 400MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
