Ultrasonic Thickness Gages
-
Product
Benchtop Unit for Universal Coating Thickness Measurement
FISCHERSCOPE MMS PC2
-
Multifaceted for coating thickness measurement and material testing. Universal multi-measuring system for parallel coating thickness measurement and material testing with up to eight measuring modules.
-
Product
Anti-Surge High Power Thick Film Chip Resistors
-
Panasonic Industrial Devices Sales Company of America
Anti-Surge High Power Thick Film Chip Resistors by Panasonic
-
Product
Underwater Thickness Gauge
Multigauge 4000
-
The Multigauge 4100 and 4400 ROV Underwater Thickness Gauges mount onto most types ROV. There are two models in the range, the Multigauge 4100 which has a depth rating of 1000m and the Titanium Multigauge 4400 which has a depth rating of 4000m.
-
Product
Ultrasonic Probes And Cables
-
The cable connects the main body of ultrasound diagnostic equipment and the probe used for echographic investigation.
-
Product
Wafer Thickness Measuring System
WT-425
-
Contact type can measure any materials within 0.2 µm (2 σ at 20℃ ±1℃). The wafer floats positions while measurement points change and it does not damage even thin wafers. Best for the process control of compound wafers and oxide wafers. (SiC, GaN, LT, Sapphire and Bonded Wafers)
-
Product
SENSOR FOR THICK & CURVED MATERIALS
S3
-
The smallest, simplest, most affordable high-precision non-contact sheet resistance sensor availableNon-contact measurement of Ohms/sq, Ohms-cm, resistivity, thickness, and moreChoose a sensor in one of four ranges, from .005 Ohms/sq to 100,000 Ohms/sqadd other sensors laterReads any conductive coatingon even the thickest nonconductive substratesOptions include PC-based productivity software, stage, and morePerformance limited by "lift off" phenomenonelevation of sensor above conductive layer must be carefully controlled
-
Product
Thickness Measurement
-
Thickness Tester is a high precision mechanical contact method thickness tester, which can be used to thickness measurement of films, sheeting, paper, corrugated paperboard, textiles, non-woven fabrics, and solid insulation materials, etc.
-
Product
Thick Film Divider
GBR-391
-
GBR-391 series high-voltage resistive dividers are made in a thick film technology on ceramic substrates (Al2O3 - 96%) with leads for through-hole mounting. Dividers are characterized by very high maximum voltage, and standard voltage division.
-
Product
3-Axis Ultrasonic Anemometer
HD2003
-
HD2003 is a 3-axis static anemometer for measuring wind speed and direction, U-V-W cartesian components of speed, wind gust, sound speed, sonic temperature, air temperature, relative humidity and barometric pressure.
-
Product
Wall Thickness Measurement Gauges
-
ElektroPhysik Dr. Steingroever GmbH & Co. KG
Portable wall thickness measuring device for non-destructive measurement of up to 24 mm. Thickness measurement of all non-magnetic materials such as glass, synthetic materials, stainless steel and composites; can also be used for objects with complex geometries.
-
Product
Ultrasonic Metal Welding
-
Ultrasonic metal welding method is used to join dissimilar metals of aluminum wire and copper for aluminum harnesses, thin copper alloys for vapor chambers and hoop materials, and aluminum laminated foil for rechargeable batteries.
-
Product
Non Contact Thickness Measurement Systems
-
Non contact thickness measurement is becoming more complicated with each passing year.From medical devices to food packaging, we understand the needs from an array of industries to successfully design non contact thickness measurement systems to meet your needs:
-
Product
Stainless Steel Low Pressure Gage
SGF
-
The Series SGF Gages have dual English/metric scales with ±1.6% full scale accuracy. The Series SGF gages are designed with 304 SS housings, and 316/316L SS wetted parts. Units can withstand ambient temperatures up to 149°F (65°C) and process temperatures up to 212°F (100°C).
-
Product
Digital Ultrasonic Maintenance System
VPE-2000
-
The Superior AccuTrak VPE-2000 is the first digitally controlled ultrasonic detector. Like two instruments in one it uses two independent sensors supported by separate electronic circuits configured specifically to their own sensor. This assures optimum sound clarity and frequency response. When switching between the airborne and contact sensors all settings are retained in memory! Digital LED meters let you establish baselines, perform trending, and accurately repeat these tests better than older more expensive analog instruments.
-
Product
Probes For Non-Contact Ultrasonic Testing
SONOSCAN CFC / CF
-
Due to the strong damping properties of air, low frequencies in the kHz range are used in air-coupled ultrasonic testing. It is therefore all the more important that the ultrasonic transducers offer a particularly high sensitivity in order to ensure high penetration and improved resolution. We achieve this, among other things, by installing preamplifiers in the receiver probe as well as by using our own Piezocomposite Technology, which enables a flexible use of the matching materials in our CFC and CF probes.
-
Product
Ultrasonic Flaw Detector
MFD660C
-
MFD660C intelligent digital ultrasonic flaw detector, Mitech concentrated years meticulously developed premium product, has a lot of advantages like unique design, sophisticated manufacturing, convenient operation, powerful function. It had received customers' favored since its inception. It can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. With full digital 640X480 TFT LCD display, it can select the operating interface style and the LCD brightness according to environment. With humanizing interface design, the waveform show delicately. It can find the defects clearly in full screen. Single hand capable for holding operation, the curve making, probe calibration and other conventional operation can be completed automatically. Core processor CPU with 400M main frequency, it can complete the complex run quickly and realize intelligent defect analysis. Low power design with large capacity and high performance lithium ion battery module， it can work more than 10 hours continuously. Full English master-slave menu, emphasizing on user experience, collecting shortcut keys, digital shuttle rotary wheel, cross menu three operating ways in one body, customers with different habits can operate it freely. It supports many languages. Its waterproof, oil proof, dustproof function can achieve IP65 protection level. It is the necessary professional precision instrument for defect detection, quality control, on-line safety monitoring and life evaluation in fields of oil, chemical, metallurgy, shipbuilding, aviation, railways and so on.
-
Product
Wet Film & Powder Thickness
-
When applying a liquid coating, by measuring the uncured film thickness, it is possible to determine the eventual dry film thickness. Applying too much coating wastes time and materials. It can also affect the performance and finish of the product. Too much wet film can cause the coating to crack as it cures; too little coating increases the risk that the substrate will not be sufficiently protected, leading to rust spots.
-
Product
Ultrasonic Leak Detector
ULD-420
-
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-420 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure. When working in unpressurized systems or the pressure is not sufficient enough to detect or verify a leak with the Receiver alone use the Transmitter.
-
Product
Ultrasonic Flaw Detector
MFD550B
-
Based on ultrasonic principle, digital ultrasonic flaw detector MFD550B can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. With full digital 640X480 TFT LCD display, it show the defect clearly under the dim light and strong sunlight environment. 0-9999mm measuring range can meet the requirement for general defect inspection in manufacturing industry, metallurgical industry, metal processing industry, chemical industry and so on. Low power design with large capacity and high performance lithium ion battery module，it can work more than 10 hours continuously. Full English master-slave menu, emphasizing on user experience, collecting shortcut keys, digital shuttle rotary wheel, cross menu three operating ways inone body, customers with different habits can operate it freely. With comprehensive performance self-checking function, it can automatically generate test reports and support for many languages. With high cost performance, it is the smart choice for the practical economic model of ultrasonic testingequipment.
-
Product
Thick Film Bleeder
GBR-350
-
GBR-350 series resistors are made in a thick film technology, on ceramic substrates (Al2O3 - 96%). High voltage resistors have an application as bleeders, which have a task to unload electric charge after disconnection of supply voltage.
-
Product
Digital Coating Thickness Gauges
-
The Elcometer range of digital coating thickness gauges has been specifically designed to provide highly accurate, reliable and repeatable coating thickness measurements on almost any substrate, whether ferrous or non-ferrous. Dry Film Thickness can be measured on either magnetic steel surfaces or non-magnetic metal surfaces such as stainless steel or aluminium using a digital coating thickness gauge. The principle of electromagnetic induction is used for non-magnetic coatings on magnetic substrates such as steel. The eddy current principle is used for non-conductive coatings on non-ferrous metals substrates.
-
Product
Epi Thickness & Composition System
Element
-
The Element system is the tool of record for wafer suppliers for high speed impurity mapping and epi thickness measurement. It is the only tool on the market with the unique combination of transmission and reflection based technology. This system is the industry standard for dielectric monitoring.
-
Product
Thickness Gauges
CMX DL+
-
The CMX DL+ has all the features of the CMX DL, plus a full featured A-Scan presentation with RF and Rectified viewing options. The CMX DL+ is equipped with 3 fully adjustable gates (start, stop, width, & Threshold). Equipped with a 20dB boost/cut attenuator, which offers added flexibility for transducer types and applications. Selectable 50 volt pulser boost or cut (100 200 volts). Truly the Cadillac of the CMX series.
-
Product
Wall Mount Ultrasonic Flowmeter
-
Gentos Measurement & Control Co.
As one of the most professional wall-mount ultrasonic flowmeter manufacturers and suppliers in China, we're featured by quality products and low price. Please rest assured to buy discount wall-mount ultrasonic flowmeter in stock here from our factory. For customized service, contact us now. Wastewater Treatment Flowmeter, Ultrasonic Flow Meter For Water Distribution, Battery Powered Ultrasonic Flowmeter
-
Product
Thick Film Passive Element
GBR-183
-
GBR-183 series resistors are made in a thick film technology, on ceramic substrates(Al2O3 -96%). Thick film resistors are characterized by a higher stability, and lower noises than a typical carbon resistors. The whole of resistor is encapsulated with epoxy resin by fluidization process. GBR-183 series elements are used both for general, and professional applications.
-
Product
Thick Film Passive Element
GBR-403
-
GBR-403 series high voltage resistors are made in a thick film technology on ceramic substrates (Al2O3 96%). These elements are used in high voltage applications requiring high stability and resistance.
-
Product
Coating Thickness Gauge - Integral
Elcometer 456
-
Whether you are measuring on smooth, rough, thin or curved surfaces, the Elcometer 456 Dry Film Thickness Gauge produces accurate, temperature stable measurements thanks to its ±1% thickness measurement capability and increased reading resolution.
-
Product
Surveyor Datalogger Thickness Meter
Multigauge 5750
-
Has a choice of Multiple Echo, Echo to Echo or Single Echo to cover all requirements. Measurements can be stored on the gauge and wirelessly transferred to the PC.
-
Product
Thick Film Heating Elements
GBR-200
-
GBR-200 series high voltage resistors are made in a thick film technology on ceramic substrates (Al2O3 96%). Those elements are used in high voltage applications requiring high stability and resistance.
-
Product
Thickness and Flaw Inspection
MultiScan MS5800
-
Eddy current testing is a noncontact method used to inspect nonferromagnetic tubing. This technique is suitable for detecting and sizing metal discontinuities such as corrosion, erosion, wear, pitting, baffle cuts, wall loss, and cracks in nonferrous materials.
