Ultrasonic Thickness Gauges
-
Product
Clamp-On Ultrasonic Flow Monitor
KATflow 10
-
The KATflow 10 is a simple ultrasonic clamp-on flow monitor, which provides an extremely cost-effective alternative to in-line flowmeters on effluent, wastewater and sludge applications. The KATflow 10 is used to monitor the flow of liquids containing higher levels of solids or entrained gas bubbles for measurements where a general flow indication is sufficient. The instrument is extremely simple to install and commission and is ideal for applications which demand good repeatability and reliable results.
-
Product
Diaphragm Strain Gauges
-
Diaphragm Strain Gauges provide a full bridge for convenient installation, different diameters, for fitting the intended diaphragm size, are available.
-
Product
48-Channel High Performance Strain Gauge Measurement Instrument
EX1629
-
48-Channel High Performance Strain Gauge Measurement InstrumentSupports quarter-bridge (120, 350Ω or user defined), half-bridge or full-bridge24-bit ADCs, sampling rates up to 25 kSa/sBuilt in programmable differential excitation -8V to 8VBuilt in selectable bridge completionConfigure signal conditioning excitation and bridge completion on a per channel basisSimple, low-cost wiring using RJ-45 telecom connectorsSupports TEDS for easy transducer detection and setupRJ-45 input connector reduces setup cost and timeBuilt in self-calibration and shunt calibrationSupports voltage, ratiometric and linear measurements other than strain measurements.
-
Product
Leather Thickness Gauge
UI-FT43
-
Leather Thickness Gauge is used to measure the thickness of leather. Place the sample in a thickness meter under a specified load for a certain time and them read the thickness. Unuo Instruments supply film thickness gauge, film thickness gauge, rubber thickness gauge and etc. Shore Durometer for rubber is also available.
-
Product
Ultrasonic Tightness Tester
Cygnus Hatch Sure
-
This portable ultrasonic leak detector is designed to locate leaks and identify seal failures in any closing appliances or compartments, such as weathertight doors on marine vessels or watertight doors (WTDs) or windows on any structures from offshore oil & gas platforms to transportation vehicles.
-
Product
Ultrasonic Leak Detector
ULD-410
-
When equipment begins to fail due to an air or gas leak or vibration, or electrical discharge, the leakage point emits an ultrasonic sound wave that is above the natural range of human hearing. The ULD-410 Ultrasonic Leak Detector converts this ultrasonic sound into a signal that can be used to pinpoint the exact location of the equipment failure.
-
Product
Pointer Type Push Pull Force Gauge
NK-20
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Easy to be operated and can be installed with all kinds of test stands and clamps.*Peak holding function and continuous.*One year free maintenance.*Compact and artistic packing, easy to transit and stock.*Two kind of unit dual show at the same time,*don't need unit conversion. *NK Series: Newton and Kilogram dual unit; *NLB Series: Newton and Pound dual unit; *ALB: Pound and Kilogram dual unit.*Needle indicates, easy to read, high accuracy.
-
Product
EHC-03 Basic Corrosion Thickness Gages
EHC-03
-
Danatronics is pleased to welcome our EHC-03 to our corrosion thickness gage family. The EHC-03 is designed to accurately and non-destructively measure metal structures subject to corrosion.
-
-
Product
Digital Push And Pull Force Gauge
HG-2-1000
-
Shenzhen Chuangxin Instruments Co., Ltd.
Digital push and pull force gauge is a universal portable force device, testing push and pull load. It is small, light, easy to take, multi-function, high precision. Applicable for all products doing push and pull load test, insert and pull out force test, destroy test, etc. It also can be combined with the machine and clamp to make up a small tester for different purposes.
-
Product
Digital Gauge Pressure
ZET 7012-I VER.2
-
ZET 7012-I VER.2 digital gauge pressure consists of primary transducer and integrated measuring module.
-
Product
Gauges & Calibrators
-
Ralston Instruments' gauges and calibrators are born from decades of experience working with technicians, project managers and facilities teams responsible for maintaining metrology instruments.
-
Product
Precision Coating Thickness Gauge Probe Range
Elcometer 355
-
Unique probe modules allow the Elcometer 355 Coating Thickness Gauge to be versatile and flexible for any coating thickness measurement application.
-
Product
Radar Level Gauge
HRRD730 Series
-
HighReach Measuring & Controlling System Co.,Ltd
At The Radar Level gauge Antenna emits and Narrows at The Microwave Pulse. This Pulse propagates in Space AT at The Speed of Light. The When IT Encounters at The Surface of at The the Measured Medium, Part of the ITS Energy IS the REFLECTED the Back and Received by at The Same, Antenna. At The Time interval The Between the transmitted pulse and the received pulse is proportional to the distance from the antenna to the surface of the measured medium.Because the electromagnetic wave propagation speed is extremely high, the time interval between the transmitted pulse and the received pulse is very small (on the order of nanoseconds). It is difficult to confirm. The 90X series 26G radar level gauge uses a special demodulation technology To accurately identify the transmitted pulse and the time interval of the pulse is received to further calculate the distance of the antenna from the surface of the measured medium.
-
Product
Height Gauges
V6
-
The height gauge V6 is the descendant of the legendary V+ line, from which thousands of copies have already been sold in workshops all over the world and are universally recognized for their easy use and their high quality.
-
Product
Ultrasonic Energy Meter
D116-PT1000
-
Gentos Measurement & Control Co.
D116-PT1000 is an upgraded version of D116, adding heat measurement function, so it can detect flow rate and calorie consumption of the fluid at the same time.
-
Product
PING))) Ultrasonic Distance Sensor
28015
-
Our PING)))™ ultrasonic sensor provides an easy method of distance measurement. This sensor is perfect for any number of applications that require you to perform measurements between moving or stationary objects.
-
Product
High Performance Two Axes Ultrasonic Anemometer
HD51.3D…
-
two-axis static ultrasonic anemometers for accurate measurements in all environmental conditions
-
Product
Thick Film Inspection
785
-
For thicker coatings such as coal tars, extruded and tape coatings, the Model 785 has a range of infinite voltage settings from 1,000 to 15,000 volts.
-
Product
Ultrasonic Probes And Cables
-
The cable connects the main body of ultrasound diagnostic equipment and the probe used for echographic investigation.
-
Product
Analog Ultrasonic Inspection System
ULTRAPROBE 100
-
The Ultraprobe senses high frequency sounds produced by operating equipment, leaks and electrical discharges. It electronically translates these signals by heterodyning them down into the audible range so that a user can hear these sounds through a headset and see them as intensity increments on the meter. Heterodyning works the same as a radio in that it accurately transforms the sounds so that they are easily recognized and understood.
-
Product
Non Rotating Spindle Type Tooth Thickness Micrometer
-
Measures the "root tangent length" of gears. Compatible modules differ depending on the model.
-
Product
Blast Nozzle Gauge
103
-
The Elcometer 103 Blast Nozzle Gauge measures the orifice size of an abrasive blasting nozzle. This gauge is used to determine the nozzle orifice wear which leads to low nozzle pressure and decreased efficiency in its performance. Nozzle orifice wear results in decreased productivity and increased abrasive media consumption.
-
Product
Digital Ultrasonic Flaw Detector
-
Are modern age portable and processor-based flaw detectors. They are made up of parts including an ultrasonic transducer, hardware & software for capturing signals and analysing them, a data logging module, and a waveform display for viewing the images and graphs.
-
Product
Semiconductor Technology, Micro Scriber + Flatness, Bow, Warp, Curvature, Glass Thickness
FLATSCAN
-
Optik Elektronik Gerätetechnik GmbH
Non contact automated 2D- or 3D measurement of warp, bow, slope and surface curvature with software module for calculation of thin film stress (wafer stress) of wafers and glass substrates.
-
Product
Flaw Detector & Thickness Gauge
DFX-8+
-
Measurement Gates: Two independent gates (Flaw), and three gates (thickness). Start & width adjustable over full range. Amplitude 5-95%, 1% steps. Positive or negative triggering for each gate with audible and visual alarms.
-
Product
Daniel Flow Gauge
2290
-
The Elcometer 2290 Daniel Flow Gauge is a simple gauge used to conduct flow measurement of thick or paste-like materials, such as paints or printing inks.
-
Product
Digital Gauge Counter
DG-5100
-
The DG-5100 is a high-resolution gauge counter having integrated structure. This counter achieves input frequency at 3 MHz which is high speed of ten times compared to conventional counter. (equivalent to a spindle velocity of 1.2 m/s at GS-3800B series)
-
Product
Contactless Wafer Geometry Gauge
MX 20x series
-
The E+H geometry gauges are based on two heavy plates mounted parallel to each other. Embedded in the plate are a set of capacitive distance sensors. The wafer will be moved manual or automatically between the plates and measured without any movement.
-
Product
SENSOR FOR THICK & CURVED MATERIALS
S3
-
The smallest, simplest, most affordable high-precision non-contact sheet resistance sensor availableNon-contact measurement of Ohms/sq, Ohms-cm, resistivity, thickness, and moreChoose a sensor in one of four ranges, from .005 Ohms/sq to 100,000 Ohms/sqadd other sensors laterReads any conductive coatingon even the thickest nonconductive substratesOptions include PC-based productivity software, stage, and morePerformance limited by "lift off" phenomenonelevation of sensor above conductive layer must be carefully controlled
