Amplifiers
increase the amplitude of a signal.
See Also: Amp, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
product
Amplifiers
MMICs
RF core has been innovating GaN-based MMIC solutions for active phased array system pursuing more ease of use, higher performance, lower SWaP (Size, Weight, and Power) as well as lower cost. We aim at integrating all components of TRM front-end for active phased array on single die.
-
product
Dual-Band RF Tuner and 4-Ch 400 MHz A/D with Kintex UltraScale FPGA - 6U VPX
Model 58891
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Accepts RF signals from 925 MHz to 2175 MHz- Programmable LNA handles L-Band input signal levels from -50 dBm to + 10 dBm- Programmable analog downconverter provides IF or I+Q baseband signals at frequencies up to 123 MHz- Four 400 MHz 12-bit A/Ds digitize IF or I+Q signals synchronously- Four FPGA-based multiband DDCs (digital downconverters)- Two Xilinx® Kintex® UltraScale™ FPGA- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- PCI Express interface (Gen. 1, 2 & 3) up to x8- Clock/sync bus for multimodule synchronization- Optional LVDS and gigabit serial connections for FPGA for custom I/O- Navigator BSP® for software development- Navigator FDK® for custom IP development- Spark® fully-integrated development system- Free lifetime applications support- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Optometers, Amplifiers, Display Meters
Optometers are a specific type of digital multimeter (DMM) used for optical radiation measurements. The particular light detector(s) connected determine the wavelength range/spectral weighting function and displayed measurement units.
-
product
Intelligent Panel Mount Meter Amplifier/ Conditioner
MODEL DPM-2
The voltage-to-frequency microprocessor makes Transducer Technique's 4-digit panel mount meters the ideal solution for meeting the measurement, display and control requirements of noisy industrial applications, OEMs and system designers. Model DPM-2 accepts any full bridge transducer. Balance and span can be selected via the front keypad, thus allowing the display to read directly in engineering units. Front panel max and tare functions are ideal for industrial weighing applications. Isolated adjustable 9-11 VDC excitation with remote sense and 90 mA drive eliminates the need for external power supplies. Rear screw terminals connectors are included.
-
product
Shunt Isolation Amplifier
Knick Elektronische Messgeräte GmbH & Co. KG.
Especially to accurately measure large DC currents via shunt resistors, ie for making isolated detection of mV voltage on shunts. Variants with calibrated range selection. Working voltage up to 3600 V AC / DC.
-
product
Wideband Distributed Amplifiers
Analog Devices GaAs MMIC-based wideband distributed amplifiers cover the dc to 65 GHz frequency range in various ultrawide bandwidths. Our design catalog includes low noise amplifiers, power amplifiers, and driver amplifier designs to meet your needs in applications such as electronic warfare, radar, electronic countermeasures, optical applications, and instrumentation. To meet diverse design requirements, some of our LNAs also offer internal-self biasing that requires only a signal drain voltage to operate.
-
product
Composite 1×24 Video Distribution Amplifier
VDA124RM-12
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
product
CATV Amplifiers
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of single-ended and differential 75 Ω broadband amplifiers service head-end, HFC infrastructure Nodes, system and line-extender amplifies, EQAM and CPE applications. MACOM’s industry leading GaAs amplifiers are offered in a range of small, plastic leaded and leadless packages operating off standard voltage rails 5,8 & 12V. Covering reverse path, 5 – 300MHz, and forward path, 45 – 1800MHz, our amplifiers offer flat gain response, low distortion and high linearity.
-
product
20-50,000 Hz Charge Amplifier
203G8
The Trig-Tek™ 203G8 accepts pickupswith sensitivities varying from 1 to 110pC/g. It has three simultaneous outputs:Acceleration with a sensitivity of 100 mVrms/Pk g; Velocity with a sensitivity of 534mVrms/Pk/ips; and Displacement with asensitivity of 100 mV/mil DA.
-
product
Ku Band Gain Control Amplifier
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
product
Amplifier
Toellner Electronic Instrumente GmbH
An electronic device that increases the voltage, current, or power of a signal.
-
product
Linear Amplifiers
Advanced Science and Novel Technology, Co., Inc.
Broadband (DC-12GHz) linear amplifier for receiver-side applicationsFeatures controlled gain from 0dB to 31.5dBFeatures input offset adjustment and input peak detectorFully differential input interface with on-chip 50Ohm terminationFully differential output interface with on-chip 50Ohm terminationOutput 1dB compression point of 1.5dBm3rd Harmonic better than -47dBc within the full bandwidth15dB Noise FigureSingle +3.3V or -3.3V power supplyPower Consuption: 530mW typicalFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 24-pin package
-
product
Portable Power Amplifier
PA30Bip-H
PA30Bip-H portable power amplifier is designed with linear amplifier principle. It is very light portable solution with three channels of current output and four channels of voltage output.
-
product
External Pre-amplifiers
Although all Spectrum A/D cards have a very powerful input section with a highly configurable input amplifier and a variety of input ranges it is sometimes necessary to have additional external amplifiers if the signal to acquire has an extremely low level. Spectrum offers a range of perfectly matching external amplifiers to cover such cases. These powerful amplifiers have been rated using the Spectrum cards and offer best performance together with high amplification rates.The amplifiers are simply connected between the signal source and the Spectrum A/D card input and can be manually switched between different settings using small lever keys. All amplifiers allow the offset compensation by using an adjustable screw.
-
product
Low-Noise Amplifier
CARM-02
HYPRES is proud to announce an Analog-RF Amplifier product. Using state-of-the-art low-noise amplifier and compact cryogenic cooler, the Cryogenic Analog RF Module (CARM-02) provides amplification with extremely low noise.
-
product
Broadband Power Amplifier
PAS-00260-10
* Solid State Power Amplifier* Gain : 49 dB typ.* High IP3, 50.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Type N Connectors
-
-
product
Double Taper Horn Antenna
MDTH series
This product is the antenna that corresponds to the radar pulse immunity test for automotive equipments. Automotive manufacturers have required the electric field strength of 600 v/m. Amplifier system and cable will be cheaper, and will contribute to the ecology.
-
product
Crank Angle Measurement System
CP-5110B Detector/CA-6000B Amplifier
CP / CA series are systems that detect the rotation angle of the engine crankshaft composed of CP-5110B Fiber Optic Crank Angle Detector, CA-6000B Crank Angle Amplifier and CP-5120 / 5130 Slit disk.CP-5110B Fiber Optic Crank Angle Detector makes it possible to detect the crank angle required for various engine performance tests such as combustion analysis with high accuracy and high response. As it has a light projecting and receiving method with an optical fiber, it provides outstanding vibration and noise resistance without a built-in electric circuit in the detector.CA-6000B Crank Angle Amplifier inputs a signal of crank angle detector and outputs a TTL level angle signal and a 1P / R pulse signal.
-
product
EMI Amplifiers
Overvoltage protection,shuts off above 29VOver-temperature protection,shut off above +100°CExcellent IP3 Class A amplifierVSWR Short and Open circuit protection
-
product
Signal Amplifier
ZET 410
The ZET 410 preamplifier is used as a signal amplifier in processing systems and various instruments and actuator control systems. It is used in industry, laboratory and mobile studies.
-
product
RF Power Amplifiers < MMICS
Macom Technology Solutions Holdings Inc.
MACOM is continually enhancing and expanding its MMIC power amplifier product portfolio to meet customers’ demanding technical challenges by leveraging state-of-the-art foundry technologies and proprietary in-house processes. MACOM partners with today’s leaders in Test and Measurement, SATCOM, Aerospace and Defense, Public Safety Radios, Wired Broadband, and Industrial Scientific and Medical applications to deliver industry leading, high-performance MMIC solutions in bare die and high performance packaging.
-
product
Thermocouple Interface Amplifiers
Analog Devices offers specialized precision thermocouple interface amplifiers that provide a simple and effective solution for measuring thermocouple temperatures. With features such as integrated cold junction compensation and a high gain precision instrumentation amplifier, these thermocouple amplifiers provide a complete signal conditioning system in one IC package. ADI’s thermocouple amplifiers are suitable for use in diverse environments to measure a wide range of temperatures. These products will save you in cost, space, and unnecessary circuit design across a broad range of applications and industries.
-
product
Microwave Amplifiers
MShU Series
*Ultrawide Operating Frequency Range*Small Size*Low Noise Figure*Low Power Consumption
-
product
Adaptive Relay, Virtex-6 FPGA - 6U VPX
Model 57624
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Super Quality Fiber
Panasonic Industrial Devices Sales Company of America
These Super Quality Fibers are designed with an extremely small beam axis curvature and gap which results in a high stability of light intensity. When combined with the FX-500 Amplifiers, the stability of light intensity is improved up to 4 times compared to traditional Fibers.
-
product
PXIe Single Channel 20GHz 30dBm RF Amplifier
3201
Model TE3201 is a single channel RF amplifier in a single slot PXIe form factor that can operate from 100kHz to 20GHz, designed for high frequency, and high power signal amplification.
-
product
Low Noise Amplifiers
Our range of ITAR Free, Low Noise Amplifiers (LNAs) cover a variety of applications but are primarily suited to airborne, maritime and ground based radar systems. LNAs are primarily intended to minimise added noise whilst providing high gain so design focusses on the parameters associated with the noise response of the amplifier. They are usually the first amplifier in the Radar detection chain and will have the lowest noise figure.
-
product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - 6U VPX
Model 57721
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three or six 200 MHz 16-bit A/Ds- Three or six multiband DDCs- One or two DUCs- Two or four 800 MHz 16-bit D/As- Multiboard programmable beamformer- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Saluki SE1022 DSP Lock-In Amplifier
SE1022 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 102 kHz. With the advantage of the latest digital signal processing technology and high-precision 24-bit ADC, SE1022 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noises. The performance of SE1022 is as good as other lock-in amplifiers brands, even better in some certain parameters, such as measurement accuracy, SNR, dynamic reserve. Otherwise, SE1022 integrates some special functions like multiple harmonic measurement and FFT, which meets the needs of scientific research and industrial application well.* Saluki SE1022 can be comparable to SRS SR830, even better and more stable.
