-
Product
Multi-Function Test & Measurement System
-
Optoplex’s Multifunction Test and Measurement System (TM100 Series) is designed to provide a flexible and cost effective optical test and measurement solution, particularly for manufacturing lines. The mainframe can be mounted in 19” rack or stationed on desk-top for ease of use. There are many selections of the pluggable modules, from tunable laser, optical spectrum analyzer, EDFA, power meter, ASE light source, optical tunable filter, optical performance monitor, …, etc.
-
Product
Flying Prober Test System
QTOUCH2204C
-
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.
-
Product
Test system for Electronic Device
PCB
-
The main focus of the test system is validation and functional testing of electronic devices. The tests include electrical parameters and logical functions of the firmware. Device groups can be stimulated externally and output signals can be acquired by the test points on the board. Limits and ranges of the acquired signals can be monitored and stored for verification.
-
Product
Cord Swiveling Test Set Up For Hair Dryer & Hair Straightner
-
SCR Elektroniks make CORD SWIVELING TEST SET UP FOR HAIR DRYER & HAIR STRAIGHTENER is used to test the Electrical accessories / appliances for their mechanical strength. Operate appliances Hair dryer or Hair straightener at rate voltage. Position appliances swivel with connection with major axis horizontal ,supply cord hanging vertically with 1N pull force. Rotate the appliance around its major axis,20 Revolutions clockwise & 20 Revolutions anti-clockwise.
-
Product
Steering Module Test Systems
-
Steering test systems for quiet evaluation of rattle, NVH & performance issues – non-hydraulic. The MB Dynamics Steering Module Test Simulator family of technologies (SMTS) is an assembly of components and software designed to facilitate the quiet testing, development, troubleshooting, and auditing of a variety of steering gear and steering column assemblies — collectively referred to here as steering modules (including components).
-
Product
IP Code Test Equipment
-
Weice Testing Instrument Co.,Ltd.
IP Code, International Protection Marking, sometimes interpreted as Ingress Protection Marking, classifies and rates the degree of protection provided against intrusion (body parts such as hands and fingers), dust, accidental contact, and water by mechanical casings and electrical enclosures.
-
Product
Environmental Testing
-
Environmental testing and accelerated ageing are testing that may be mandated for certain regions or required standards. But for many products, this testing is not mandated, but if any claim to performance is made then testing should be done to have evidence. In addition, it can help ensure less product returns to defective products that may after sold become faulty due to external environmental impacts.
-
Product
Cr(VI) ROHS Testing
-
Rocky Mountain Laboratories, Inc.
Rocky Mountain Laboratories is now offering testing to detect Cr(VI) on the surface of materials. ROHS standards for export of materials to Europe require testing for Cr(VI), and with our XPS instrument, we can provide that testing.
-
Product
Transformer Test System
-
Transformer testing instrument, can be used as a stand-alone device and has the highest efficiency. Can be used in power transformers, network communication transformers, etc.
-
Product
Test System
RF-1 ATS
-
The RF-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
PCB Test Fixtures
-
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Product
IoT Testing
-
The Internet of Things (IoT) is the new buzzword, with predictions ranging from “it’s just another connected network” to “this is the new sliced bread of the generation”. Every new idea will cause change; radical ideas will have a greater impact, while revolutionary ideas change the course of humanity. IoT promises to be a revolutionary idea.
-
Product
Interior Wiring Testing
-
With automotive interior designs becoming more luxurious, cabin space features such as ambient lighting and seat / steering wheel controls have increased the demand for interior wiring testing. Jackmark Engineering has years of experience supplying test equipment for instrument panel manufacturers and have increased their portfolio to include all aspects of interior wire harness testing.
-
Product
ESD Testing & Latch-Up Testing Services
-
EAG is an industry leader in ESD testing (Electrostatic Discharge) and Latch up testing. Our highly experienced engineering team use their industry leading knowledge and years or real world experience of the latest semiconductor technologies, circuit design, and device physics to optimize our customer's ESD and latch-up results. Human Body Model (HBM) and Machine Model (MM), Charged Device Model (CDM), Latch-up, Transmission Line Pulse (TLP).
-
Product
Product Safety Compliance Testing
-
Compliance with electrical safety standards and directives is a mandatory requirement worldwide. Our comprehensive NATA accredited safety testing facility at our Sydney Branch (since 1996) and the A2LA accredited Melbourne facilities at Keilor Park , provide a choice of NATA or A2LA accredited testing.
-
Product
IP Fax/ Modem Testing
-
To successfully deploy fax services requires extensive network design, test and traffic engineering. Test equipment can prove valuable in this process, if it can: Generate and receive fax signals in bulk over wired and wireless networks, monitor and distinguish fax signals in real time for traffic engineering and network design purposes, and analyze fax signals after capture for troubleshooting failed or poorly handled calls.
-
Product
Mobile App Penetration Testing
-
To verify the functionalities of your software, to check for the quality of your product, and to see that the applicationis working against business requirements, opt for Functional Testing.
-
Product
Precision Electronic Test Leads
34133A
Accessory Kit
The Keysight 34133A precision electronic test leads are designed specifically for working with small components and dense circuit boards. Each kit includes two test leads (one red and one black).
-
Product
Temperature/Humidity Testing
-
Quest has 14 environmental chambers ranging in size from 1 cubic foot to over 1,000 cubic feet, covering temperatures from below -100C to temperatures exceeding 200C. Our temperature/humidity test chambers include one of the largest walk-in chambers (15 x 10 x 8 ft) in New England, table top, high humidity, thermal shock, and high ramp rate test chambers. We can provide a wide range of temperature/humidity conditions on a variety of different product shapes and sizes, from extremely small to large products.
-
Product
Relay Testing System
UNO
-
With high power outputs package in an extremely compact and rugged system, the UNO has a tremendous power-to-weight ratio. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability. This hi-tech solution enables the testing of many different functions required in relay testing without the need of additional accessories.
-
Product
Test Leads
-
PMK Mess- und Kommunikationstechnik GmbH
It is used to test and measure the current in a circuit. These are simple devices which are coated and colored to indicate positive and negative with the device connector on one end.
-
Product
ICE/Hybrid Propulsion Testing
-
Vehicle manufacturers and suppliers are facing global challenges and need to develop solutions to avoid further greenhouse gas emissions and improve local air quality. To meet these challenges, the industry must continue to optimize the performance of traditional combustion engines and invest in the hybridization of powertrains. We are highly committed to helping you develop zero-impact emission mobility solutions with a tailored offering that perfectly fits to your specific needs. Our holistic approach enables us to support you in the management of even the most complex testing tasks.
-
Product
Spring Testing Machine
-
This machine is designed to test laminated springs and coil springs. The test is held under laminated springs and coil springs. The Cabinet comprises of the hydraulic unit, the hand wheel of the pump and the release valve handles are outside the cabinet for easy operation. This compact base carrier two fixed upright and four horizontal plates. The first and the third plates with two small uprights from an adjustable frame. The second and the fourth plates are fixed. A square threaded wheel arrangements provided for adjusting the height of the springs.
-
Product
End-to-End Flight Line Confidence Test Set
MEON™
-
MEON™ is an end-to-end flight line confidence test set for directional infrared (IR) countermeasures (DIRCM) and ultraviolet (UV) missile warning systems. It also incorporates an IR beacon and an IR detector to provide complete, end-to-end testing, alignment checks and calibrated radiometric measurement of DIRCM.
-
Product
Optical Testing
-
We place a great emphasis on our ability to test everything we produce and supply. This has provided the impetus for us to design and build comprehensive testing facilities that include standard as well as custom-made testing equipment.
-
Product
Partial Discharge Testing Equipment
3i
-
The portable multipurpose 3i device (Intellectual Insulation Indicator) is for eff ective high-voltage equipment insulation monitoring on-line. The 3i device measures and analyses partial discharges (PD). For eff ective PD measurement and noise rejection, there are two types of sensors used in the device: the acoustic sensor and the TEV sensor. Both the sensors are built into the device case, and so do not need any connection cables. The device is supplied in a strong metal case; at the faceplate there are the colored screen and two buttons: power button and function button.
-
Product
Functional Testing Services
-
We manage an in-house team of testing specialists having sufficient experience to perform quality functional testing activities.ImpactQA exhibits cross-browser & cross-platform testing capabilities together with the latest interoperability testing methods to assess functionalities across multi-faceted systems.Unlike other functional testing services, our testing model is loaded with adaptable properties to perform white-box testing and functional testing of Java and .Net applications.
-
Product
VLF Testing and Diagnostics Unit
Viola TD
-
Cable testing and diagnostics with the BAUR viola TD. The portable and high performance high-voltage testing and diagnostics device is available in two different configurations:viola: Used for cable and cable sheath testing of electrical equipment and medium-voltage cables up to 35 kV. Another function is insulation testing on electrical equipment. viola TD: Expands the functional scope of viola with the tan delta diagnostics and Monitored Withstand Test (MWT) that combines the cable testing and dissipation factor measurement. This allows for an accurate and comprehensive assessment of the cable condition.* Cable testing and dissiation factor diagnostics in one device* High performance and compact* Easy and quick test setup* Automatic testing and diagnostic sequences
-
Product
EMF Exposure Test
sXcTEM835
-
Tests radiofrequency electromagnetic field exposures from mobile communication devices operating in the 900 MHz region (additional frequencies upon request). The setup is based on two Crawford TEM cells that are blindly excited by a fully computer-controlled signal unit.
-
Product
DVB Coverage & Drive Test
DVB-T and DVB-T2
-
DVB-T and DVB-T2 Coverage Measurement and Drive Test solutionb by using of common RF- and GPS- receiver hardware. The solution turns a laptop into a powerful coverage measurement and drive test device.
