Filter Results:
Products
Manufacturers
Applications
Motion Simulation
-
Product
Motion Simulator For Test Systems
Metis
-
METIS is a motion simulator for sensor and end system level testing. Configurable design allows you to create system you need! - 1-axis rate table for gyro testing - 2-axis unit for 6DOF accelerometer and gyroscope testing - 3-axis Gimbal system for simultaneus Yaw, Pitch and Roll stimulus.
-
Product
Benchtop & VXI Instruments
-
NAI offers a wide range of Benchtop and VXI card-based motion simulation and measurement instruments specifically designed for defense, commercial aerospace and industrial applications. Noted for their best-of-breed performance, these innovative and highly reliable instruments are used in a broad range of programs by customers world-wide. Typical applications include design; simulation; production test; and calibration of airborne, ground-based, and shipboard systems such as navigation control, signal retransmission, fire control, LVDT/RVDT simulation, and test.
-
Product
5-Axis Hardware-In-the-loop Systems
-
Combining a 3-Axis Flight Motion Simulator (FMS) with a 2-Axis Target Motion Simulator (TMS) leads to a 5-Axis motion simulator design. This allows comprehensive HardWare-In-the-Loop tests (HWIL) for testing and development of guided missiles, munitions and other inertial systems. Almost 100% of all HWIL systems worldwide delivered over the last 50 years have been designed and built by ACUTRONIC and CARCO Electronics.
-
Product
Aircraft Instrument Test Equipment
-
Centrifuge systems are designed to apply a large centrifugal force to a payload. While this can also be accomplished with a single axis motion simulation table system, a centrifuge is typically required for applications with larger payloads and/or higher g requirements. Ideal Aerosmith’s line of centrifuge systems is used for a broad range of g-testing applications, testing payloads up to 200 lbs (91 Kg) and 1,000 g s.
-
Product
3-Axis Motion Simulators
-
When a device under test needs to be stimulated with simultaneous movements around three axes, then a product from the ACUTRONIC three-axis motion simulator range is the right choice. Independent motion simulation in three axes makes them very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
Product
Motion Simulation
-
Exail's motion simulators are at the forefront of calibrating and testing inertial sensors, navigation systems, and optronic payloads across diverse applications, from traditional land vehicles and aircraft to emerging sectors like autonomous vehicles and wearables. With 60 years of expertise, Exail's rate tables deliver unparalleled performance, accuracy, and reliability, offering a cost-effective solution tailored to meet customer needs at every stage of product development. From concept to maintenance, Exail provides comprehensive support, ensuring the success of each project
-
Product
Fast 6-Axis Hexapod
H-900KSCO
-
Physik Instrumente GmbH & Co. KG
Reference-class 6-axis positioning system. Parallel-kinematic design for six degrees of freedom making it significantly more compact and stiff than serial-kinematic systems, higher dynamic range, no moved cables: Higher reliability, reduced friction. Powerful digital controller, open software architecture. Optional: Software for avoiding collisions in restricted workspace. Fields of application. Motion simulation: Motion profile compatible according to ISO 20672, ISO 8728, and ISO 16328. Industrial production, tool machines, automotive industry, shipping.
-
Product
2-Axis Rate and Position Tables
-
When a device under test needs to be stimulated with simultaneous movements around two axes, then a product from the ACUTRONIC two-axis motion simulator range is the right choice. Due to their independent motion simulation in two axes they are very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
Product
Advanced 8-Axis Servo & Stepper Motion Controller with Modular Design
PCI-8158
-
The PCI-8158 delivers high-frequency pulse rates of up to 6.55 MHz and features hardware-controlled emergency input stop, software security protection to avoid plagiarism, card index switch, and linear/circular run at the same time for that exceed the industry"s cost over performance requirements. Compatible with Mitsubishi, Panasonic and Yaskawa servos and steppers, the PCI-8158 allows complex moving patterns through multiple axes that move with linear and circular interpolations using continuous contouring. Applicable for various linear-wise and circular-wise trajectories, the PCI-8158 delivers the smoothest motion control for a wide-range of manufacturing applications. Besides, PCI-8158 design is modularized. ADLINK provides extension board for distributed I/O control, high-speed triggering and ECAM control.
-
Product
Distributed Single-Axis Motion Control Modules for Mitsubishi, Yaskawa and Panasonic
MNET-MIA
-
ADLINK's Motionnet products provide system integrators with a simple configuration and reduced wiring method for a cost-effective solution for motion applications utilizing multiple single axes. With this new concept of direct plug-in modules, the amount of space used and the amount of wiring required is greatly reduced from traditional terminal board connections.
-
Product
4-Axis Pulse Motion Controller
AMP-104C
-
The AMP-104C is a cost-effective 4-axis motion controller card with a PCI Express® interface that can generate a pulse train up to 4.9MHz to control a motor. With more general purpose IOs and 4-channel encoder feedback input, the AMP-104C can be used for a multitude of scenarios or applications. As a motion controller, the AMP-104C provides non-symmetric acceleration and deceleration speed profile settings, T-curve and S-curve speed profile control, and selection of motion stop method.
-
Product
DSP-Based 4/8-Axis Advanced Pulse-Train Motion Controllers
AMP-204C/AMP-208C
-
ADLINK"s new AMP-204C/AMP-208C DSP-based 4/8-axis advanced pulse-train motion controllers incorporate up-to-date floating-point DSP and FPGA technology, enabling high pulse output and encoder input frequency up to 6.5 MHz and 20 MHz respectively. Leveraging ADLINK" s Softmotion technology, the AMP-204C/AMP-208C offer impressive comprehensive and application-oriented motion functionality to reduce development time while maintaining superior throughput and accuracy. Superior synchronous motion control performance combines with point-table function integrating multi-dimensional interpolation, such as 3D linear/circular/spiral interpolation with enhanced trajectory and velocity planning, for contouring applications in semiconductor, display and conventional manufacturing industries. The AMP-204C/AMP-208C also support PWM control with three different control modes for frequency or duty cycle, benefiting laser engraving/marking/cutting applications. Moreover, hardware-based position comparison and trigger output are applicable in AOI applications.
-
Product
3U cPCI Synchro/Resolver Simulation Board
75DS2
-
NAI’s 75DS2 is a Synchro/Resolver Simulation Board with four independent, isolated channels. These channels can incorporate up to four Digital-to-Synchro/Resolver Simulation Converters with 1.5, 2.2, or 3 VA drive capability, or either two or four Digital-to-LVDT/RVDT Simulation Converters. One of the outputs on each channel can be grounded without affecting performance.
-
Product
Centralized Motion Controller
-
ADLINK‘s pulse train controllers provide comprehensive and application-oriented motion functions for servo and stepper motors through digital signal processing (DSP)-based and Application Specific Integrated Circuit (ASIC)-based two pulse train mode controllers to achieve excellent synchronous motion control and precise positioning suitable for laser engraving, marking and cutting applications in semiconductor, AOI, and conventional manufacturing industries.
-
Product
Solar Array Simulator DC Module, 65V, 8.5A, 510W
E4361A
-
The Keysight E4361A is a 510W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
Product
PXI RTD Simulator Module, 8 Channel, PT100
40-263-401
-
The 40-263-401 is an 8-channel PT100 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI RTD Simulator Module, 16 Channel, PT1000
40-263-203
-
The 40-263-203 is a 16-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PXI/PXIe Resolver Simulator Module, 2-Banks
41-670-203-AABBCC
-
The 41/43-670-203 is ideal for the simulation of Resolvers. It has two banks, each capable of simulating the output of a single 5 or 6-wire resolver.
-
Product
Distributed 4-Axis Motion Control Modules (with High-Speed Trigger Function)
MNET-4XMO-(C)
-
The MNET-4XMO is a 4-axis motion controller module for Motionnet distributed motion systems. It can generate fast frequency pulses (9.9 MHz) to drive stepper or servomotors in the machine automation field. As a motion controller, it can provide comprehensive motion functions which include 2 axis circular interpolation, 2-4 axis linear interpolation, or continuous interpolation for continual velocity and so on. Also, changing position/speed on the fly is available with a single axis operation.
-
Product
Load Simulator
-
The load system is intended for testing satellite power supply systems; due to the integration with a solar array simulator and a battery simulator, it can perform validation and commissioning of satellite power supplies. The system is equipped with regenerative electronic loads and customer-specific high-power switching matrices for routing the DUT channels to the relevant loads. The individual voltages and currents for each channel can be read back via a Keysight Technologies switch mainframe.The system is equipped with high electrical power; its loads are capable of feeding the energy back into the power grid.
-
Product
VXI 12-Channel, 3-Wire LVDT/RVDT Simulation
65DL2
-
NAI’s 65DL2 is a 12-channel, 3-wire, LVDT/RVDT Simulation Instrument on a VXI board. This single-slot, message-based board features up to 12 stimulus channels of 3-wire LVDT/RVDT, wraparound self-test, and onboard programmable excitation supply. The board is uniquely versatile, as each excitation input and output voltage is programmable. In addition, each channel can be programmed to be controlled by an external DC voltage. A replacement for the 5410C-83, the 65DL2 is ideally suited for defense, commercial aerospace, and industrial applications.
-
Product
Single Stream STANAG3910 Electrica lTest And Simulation Module – Rafale – for PCI
APXX3910-EN
-
Single Stream STANAG3910 Test and Simulation Module – Rafale – for PCI with 1 dual redundant HS/LS channel and onboard Electrical Front End. The APXX3910-EN is a functional replacement for model APX3910-EN.
-
Product
PXI/PXIe Battery Simulator Module, 6-Channel
41-752A-001
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
64-Axis PCIe EtherCAT MainDevice Motion Controller
PCIe-8338
-
ADLINK PCIe-8338 is a hardware-based EtherCAT motion controller able to support up to 64 synchronized axes and over 10,000 points simultaneously. The PCIe-8338 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in semiconductor, electronic manufacturing, and others. The PCIe-8338 provides an out-of-shell application-ready (APS) function library to generate multi-dimensional, highly synchronized, time-deterministic event-triggered motion & I/O control. A wide range of compatible 3rd party SubDevice are easily designed with ADLINK's APS function library. ADLINK's MotionCreatorPro 2 utility is fully compliant with the Microsoft Windows environment, that allows complete EtherCAT motion and I/O configuration and function evaluation as well as compiling program download functions.
-
Product
PXI RTD Simulator Module 6-Channel PT1000
40-262-102
-
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel
41-752A-003
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Single Stream STANAG3910/EFEX Test And Simulation Module for PCI
APXX3910
-
STANAG3910/EFEX Test and Simulation module for PCI with 1 dual redundant HS/LS channel and onboardFibre Optic Front End (FOFE). Easily select between EFAbus and EFEX modes for Tranche II Eurofighter. The APXX3910 is a functional replacementfor model APX3910.
-
Product
PXI-7342, 2-Axis, Stepper/Servo PXI Motion Controller Module
779036-02
-
2-Axis, Stepper/Servo PXI Motion Controller Module—The PXI‑7342 is recommended for both simple and complex motion applications. It includes dual processors, a real-time onboard OS, and multiaxis interpolation. The PXI‑7342 offers blended motion trajectory control and fully coordinated circular, linear, point-to-point, gearing, and vector-space control in either embedded motion operation or host-centric programming environments. NI provides contouring capability for more complex moves. The onboard CPU uses an embedded real-time OS that has event-driven multitasking control. With this approach, several motion control programs and processes can operate simultaneously on the controller independently of the host PC and with no outside program interaction unless the host program or user configuration initiates it.
-
Product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module
41-670-XYZ-AABBCC
-
The 41/43-670 range is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. Available with up to four banks, each bank is capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
Product
VXI 16-Channel, 2-Wire LVDT/RVDT Simulation
65DL1
-
NAI’s 65DL1 is a 16-channel, 2-wire, LVDT/RVDT Simulation Instrument on a VXI board. This single-slot, message-based board provides 16 independent, transformer-isolated, LVDT/RVDT, programmable 2-wire outputs (up to 34 V), wrap-around self-test, and an onboard programmable excitation supply.
