Motion Simulation
-
product
Direct Drive Motors And Motion Systems
HEIDENHAIN offers the largest direct drive motor range on the market via ETEL. Solutions range from high-end motion systems with nanometer precision to industrial applications requiring high torque. And like HEIDENHAIN, ETEL builds its linear and torque motors, along with motion systems, on a foundation of superior knowledge and technical expertise, disruptive technology and tireless quality control. Customers reap the benefit: the most cutting-edge, reliable and precise motion control solutions available.
-
product
GPS And GNSS Simulators
Safran’s GPSGlobal Positioning System is a navigation satellite system. See also / GNSSGlobal navigation satellite system (GNSS): A general term describing any satellite constellation that provides positioning, navigation, and timing (PNT) services on a global or regional basis. See also satellite simulators are easy to use, scenario-based instruments that combine a powerful, feature-rich platform with industry-leading value and affordability for any requirement for GPS testing.
-
product
Playback And Noise Simulation
Our systems make sounds and vibrations perceptible – from the pure, aurally accurate playback of binaural recordings to the realistic reconstruction of sound fields and background noise.
-
product
ECU Simulator
PT-LabCar
PT-LABCAR is an open and scalable Hardware-in-the-Loop (HiL) system. It is designed for open- and closed-loop testing of ECUs specifically in the powertrain application domain. The system can be used to run automated regression tests for the release of software variants as well as for the validation of control and diagnostic functions in early phases of ECU development.
-
product
Transistor-Level Defect Simulator
Tessent DefectSim
Tessent DefectSim is a transistor-level defect simulator for analog, mixed-signal (AMS), and non-scan digital circuits. It measures defect coverage and defect tolerance. Tessent DefectSim is perfect for both high-volume and high-reliability ICs. Tessent DefectSim replaces manual test coverage assessment in AMS circuits needed to meet quality standards such as ISO 26262 and provides objective data to guide improvements in DFT. Tessent DefectSim dramatically reduces SPICE simulation time compared to simulating every potential defect.
-
product
HUFF-DUFF SIMULATOR
HF/DF
HUFF-DUFF is a High Frequency Direction Finding radio system used during WWII to locate German Submarines for destruction. This device simulates the receiver signals including code encripted transmission for display on any oscilloscope for interactive museum displays.
-
product
Solar Array Simulator
SAS
AMETEK Programmable Power, Inc.
A spacecraft solar array is subjected to large temperature excursions, varying insolation (the amount of sunlight falling on the array), mechanical changes and aging, which substantially effect both its short and long term performance. In order to test the spacecraft's power environment, a cost-effective solution for ground based testing is to utilize a solar array simulator.
-
product
Simulation Systems
GSIM
The GSIM avionics IO platform builds on The Goebel Companyʼs long historyin computer architecture and realtime simulation. Weather your IOrequirements are simply driving a cluster of displays, or driving a fullcomplement of avionics IO, GSIM has the solution for you. GSIM providesthe highest IO count in single chassis rack mount or desktop configurations.GSIM configurations are delivered with Linux Real-time systems.
-
product
Flight Simulator Tester
Excalibur’s Flight-Sim Tester is a hardware and software solution for enabling near-real flight testing scenarios for airborne system testing (avionics testing).
-
product
Environmental Simulation Testing
MET's Environmental Simulation Labs, on both coasts, employ numerous environmental chambers, including several large walk-in chambers. Hydraulic and electro-dynamic shakers are used for a wide range of vibration testing, from ISTA packaging to seismic compliance testing. MET's hydraulic vibration systems are capable of full level (Zone 4) seismic simulation.
-
product
Multi-Domain Simulation
Every product engineering team deals with questions in the virtual prototyping phase, many of these covering multiple engineering domains. ESI's Visual-Environment multi-domain modelling allows these teams to work together in a single user environment, around a single core compute model. This multi-domain simulation environment has the capacity to integrate all virtual prototyping problems across CAE domains. In addition, its user-friendly interface and automation features empower engineering teams to be ever more productive!
-
product
Simulation Equipment
Zhengzhou SMS Electric Co.,Ltd
Low and High Voltage measurement simulation devices.
-
product
MIMIC NetFlow Simulator
MIMIC NetFlow Simulator generates a variety of flows and enables you to fully test your applications. Since you have a complete control over generated flowsets you can easily verify that your graphing application is correctly displaying the values and your collector correctly collects precisely generated flowsets.
-
product
NIBP Simulators
The full-featured SC-5 SimCube® NIBP Simulator provides ECG, Resp, Arrhythmias, Pacer Simulation, IBP, and more for accurate biomedical testing. The SimCube simulates real-life oscillometric pulses by varying both the shape and size of the wave as cuff pressure changes.
-
product
UE Simulator
With Simnovus, you get superior value as our software runs on COTS and SDR enabling you to deploy multiple test beds. You do not have to spend millions on expensive Capex.
-
product
Environmental Simulation Testing
Innovative Testing Solutions, Inc.
We have multiple chamber capabilities of simulation most environmental conditions. Our chamber range in capacity from 1 ft3 to 64 ft3 volume. Specialty chambers include air-to-air thermal shock, inert gas injection oven, high/low pressure water spray and direct-injection LN2 chambers.
-
product
Resistor Simulation Card
SET-1210
The card has two ranges of values that meet the requirements of most functional test systems.The SET card is designed for applications in which resistive sensors provide information about parameters such as temperature (e.g. when testing motor controls)Each channel of the SET-1210 resistor simulation card is able to simulate the common short-circuit and no-load conditions, which can occur in a system due to faulty wiring or sensors.
-
product
Training & Simulation Devices
Designed to minimize instructor input and provide realistic, automated response.
-
product
Ring Wave Simulators
Suzhou 3ctest Electronic Co.,Ltd.
Ring wave interference on electronic line, control line and signal line can be caused by transient due to switch of mains and controlled switch or lightening strike. RWS 600 is designed to conduct immunity test for electronic and electrical device.
-
product
Radio Link Simulator
RLS-2100
Square Peg Communications Inc.
It is the most comprehensive, with unparalleled impairment simulation, real-time multi-satellite orbit calculation, full motion support and integrated GPS simulators. It is the most flexible, providing end-to-end or single link simulation of wideband terrestrial and satellite networks, satellite selection via open standard interfaces, and facilities to enable seamless integration into more complex test beds if required. It supports the highest bandwidth and has an intuitive, user-friendly interface. And it does it all in one box.
-
product
High-Mount Outdoor Infrared Motion Sensor
ENVIROMUX-IMD-OHM
High-mount outdoor weatherproof sensor with 94 detection zones. Unique pyro-element provides multiple pattern detection and accurate discrimination function for spot temperature changes of moving objects. Drastically reduces false and missed alarms caused by severe outdoor environmental changes. Upper and lower area must be activated to generate an alarm condition. Summer night compensation, advanced temperature compensation, and vegetation sway analysis logic. Ideal detection area setting – adjustable length/spot detection. Registers movement in area covered: 13/18/30/40 ft and 85° wide. LED indicators for operation and system status. Unwanted detection areas can be eliminated using the included area masking seal. Mounting height: 8.3 to 10 feet. Tamper switch opens when cover is removed. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: -4 to 140°F (-20 to 60°C). IP54 compliant. Powered by ENVIROMUX-2D/5D/16D.
-
product
Railway Motion Control Unit
RMCU
The Railway Motion Control Unit – RMCU is a high-performance strapdown system developed for Railway applications to determine the absolute orientation (Heading, Pitch, and Roll) and motion parameters (Angular Rates and Linear Accelerations) for any Railway Platforms on which it is mounted. Orientation is determined with high accuracy for both motionless and dynamic applications.
-
product
ESD Test Simulator
ONYX16
The ONYX is a state of the art electrostatic discharge simulator available in 16kV or 30kV versions. It is the most ergonomic 30kV ESD gun without an additional base control unit that can be battery or mains operated. The easy to use touch screen, ergonomic design, modular RC units, multilingual interface, remote control software, built-in LED light and temperature & humidity display allows for trouble-free use of the ONYX in all types of test sites.
-
product
LXI Simulation Tool
60-901-001
This tool will simulate all of our PXI & LXI switching products and most of our PXI simulation products allowing for code development independent from your application hardware
-
product
Rotary Motion Logger Sensor
NUL-226
This sensor measures angles, rotations, rotation speeds or rotationacceleration. The sensor has a pulley connected to its shaft and the pulley rotation is measured. This sensor has four modes of operation: degrees, rev/s, rad/s, rad/s2.
-
product
Motion and Sensor Additional Instruments
Our expansive line of Trig-TekTM motion and sensor instruments offers a myriad of test and measurement functionality.
-
product
NIBP Simulator
SC-3 SimCube®
This NIBP only simulator provides features to perform basic NIBP testing of a patient monitor. Features one-button operation for quick testing of patient monitors and optional Battery Boost Option. Optional accessories provide all you need to test the NIBP parameter on any type of patient monitor.
-
product
Modbus Plant Simulator
If you are an Industrial Control engineer or technician dealing with Modbus RTUs, PLCs, Drivers and SCADA servers, you must have Modbus TCP Plant Simulator is your toolbox. With this tool, you can test and verify your SCADA tag names, IO Server mappings, Modbus addresses, alarms, visualization displays, historians, reports, data communication channel throughput, controls, and more without deploying even one RTU or PLC.
-
product
ESD Discharge Simulator
Model 9910 PurePulse/PinScan
Model 9910 PurePulse / PinScan is used to determine the ESD susceptibility level of electronic devices up to ±4kV. PurePulse generates ESD pulses up to 4kV for testing electronic devices for susceptibility to Electrostatic Discharge (ESD) using HBM, MM and HMM models. PinScan provides automatic sequencing of ESD testing of up to 128 pin devices, applying a discharge, thenperforming a curve-trace test to identify a failure.
-
product
Flash Solar Simulators
Sciencetech manufactures a range of flash solar simulatorsSee the Flash Solar Simulator Overview to compare products across different product lines.





























