ADLINK Technology Inc.
ADLINK Technology Inc. (TAIEX:6166) leads edge computing, the catalyst for a world powered by artificial intelligence. ADLINK manufactures edge hardware and develops edge software for embedded, distributed and intelligent computing– more than 1600 customers around the world trust ADLINK for mission-critical success. ADLINK contributes to open source, robotics, autonomous, IoT and 5G standards initiatives across 24+ consortiums, driving innovation across industries. For over 25 years, with 1800+ ADLINKers and 200+ partners, ADLINK enables the technologies of today and tomorrow, advancing technology and society around the world.
- +886-3-216-5088
- +886-3-328-5706
- service@adlinktech.com
- No. 66, Huaya 1st Rd.,
Guishan Dist.
Taoyuan City, 333411
Taiwan, Province of China
-
Product
32-CH Sinking Type Digital Ouput EtherCAT Module
EPS-2132
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
Dual-port Isolated CAN Interface Cards
PCI-7841/cPCI-7841
CAN Interface
The PCI-7841/cPCI-7841 is a Controller Area Network (CAN) interface card. It supports a dual-port CAN's interface that can run independently or bridged at the same time. The built-in CAN controller of this card is Philips SJA1000, which provides bus arbitration and error detection with auto correction and re-transmission function.
-
Product
Value Family 9th Gen Intel® Core™ i7/i5/i3® Processor-Based Embedded GPU/AI Platforms
MVP-5100-MXM Series
Industrial Computer
- 9th Gen Intel® Core™ i7/i5/i3 LGA processor- Dual SODIMMs sockets for up to 32GB DDR4- Abundant I/O: Up to 4x additional DP 1.4 from MXM, 2x DP++, DVI, VGA, 3x GbE, 3x COM, TPM2.0- 3x USB 3.1 Gen 1, 3x USB 2.0- Rich storage options: 2x 2.5" SATA, M.2 2280
-
Product
10 Gigabit Ethernet AdvancedTCA® Fabric Interface Switch Blade
aTCA-3430
Switch Blade
The aTCA-3430 is a high performance 10G Fabric switch blade for AdvancedTCAR platforms. This product is ideal for bandwidth intensive telecom applications such as wireless access controllers, DPI/security network, IPTV, IP multimedia subsystems, RNC/BSC, broadband access/bearer networks, data centers, and LTE/4G network applications. The aTCA-3430 provides 10GbE hub-to-node connectivity and integrated switch silicon that supports load balancing, priority queues, packet classification, and flow control to enable strict bandwidth management for implemented applications.
-
Product
3U Enclosure with 32-bit Backplane, CompactPCI Redundant Power Supply
cPCIS-1202
Backplane
- Dual 3U CompactPCI® systems, each with five peripheral slots and one system slot- 1/1 250 W CompactPCI® Power supplies- Suitable for both rack-mount and desktop applications- Comprehensive EMC shielding- Optional rear I/O configuration (cPCI 50mm depth RTMs)
-
Product
Compact AI GigE Vision Systems for the Edge with NVIDIA® Quadro® GPU
EOS-i6000-P Series
-
The ADLINK AI Plug-and-Play (PnP) Solution is a set of ADLINK AI edge hardware and data connectivity platforms that help our partners build and deploy AI solutions faster and simpler. With ADLINK Data River™ enabled at AI edge platforms, devices, AI inferences, and data integrations, the AI PnP Solution offers a crossplatform,flexible, scalable solution that delivers business value.
-
Product
Qseven® Standard Size Module With Intel® 6th Gen. Atom® X6000 Processors (Formerly Elkhart Lake)
Q7-EL
Computer on Module
The ADLINK Q7-EL is a Qseven module that supports Intel Atom® x6000 (x6425RE, x6414RE, x6413E) processors (formerly Elkhart Lake) with integrated Intel® UHD graphics and high-speed interfaces. With mechanical dimensions of 70mm width, 70mm length, and 2.3mm of overall height, Qseven ranks as one of the smallest COM standards currently available. Q7-EL modules support up 16GB LPDDR4 memory, up to 256GB eMMC storage and are also available with rugged operating temperature range and low power envelope, making them a perfect match for mission critical fanless edge computing applications that require safety and reliability at all times.
-
Product
3 PICMG® CPU, 4 PCI™, 7 ISA Slots Backplane
HPCI-13S4LU
Backplane
- Segment: 1- Slots: 3 PICMG® CPU, 4 PCI™, 7 ISA- Supports AT, ATX power supplies- Dimensions: 314.7 mm x 259 mm
-
Product
SMARC Short Size Module with Freescale i.MX6 Solo, DualLite, Dual or Quad Core Processor
LEC-iMX6
Computer on Module
The SMARC ("Smart Mobility ARChitecture") is a versatile small form factor computer Module definition targeting applications that require low power, low costs, and high performance. The Modules will typically use ARM SOCs similar or the same as those used in many familiar devices such as tablet computers and smart phones. Alternative low power SOCs and CPUs, such as tablet oriented X86 devices and other RISC CPUs may be used as well. The Module power envelope is typically under 6W.
-
Product
6U CompactPCI 6th/7th Gen Intel® Xeon® E3 and Core™ i3/i7 Processor Blade
cPCI-6636(KL) Series
Processor Blade
The ADLINK cPCI-6636 Series is a 6U CompactPCI® processor blade based on the 6th/7th Generation Intel® Xeon® E3 and Intel® Core™ i3/i7 Processors with Intel® HM170 or CM236 Chipsets. The cPCI-6636 supports up to 16GB onboard DDR4-2133 memory and 16GB DDR4-2133 via SODIMM. Total memory capacity is up to 32GB of DDR4-2133. The cPCI-6636 is a highly integrated processor blade fit for mission critical applications in industries ranging from automation to defence.
-
Product
RS-422/RS-485 Repeater
ND-6510
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
16-Axis PCIe EtherCAT MainDevice Motion Controller
PCIe-8332
Motion Controller
ADLINK PCIe-8332 is a hardware-based EtherCAT motion controller able to support up to 16 synchronized axes and over 10,000 points simultaneously. The PCIe-8332 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in semiconductor, electronic manufacturing, and others. The PCIe-8332 provides an out-of-shell application-ready (APS) function library to generate multi-dimensional, highly synchronized, time-deterministic event-triggered motion & I/O control. A wide range of compatible 3rd party SubDivice are easily designed with ADLINK's APS function library. ADLINK's MotionCreatorPro 2 utility is fully compliant with the Microsoft Windows environment, that allows complete EtherCAT motion and I/O configuration and function evaluation as well as compiling program download functions.
-
Product
Client Type COM-HPC Size C Module with 13th Gen Intel® Core™ Desktop Processor
COM-HPC-cRLS
Computer on Module
ADLINK’s COM-HPC-cRLS COM-HPC Client Type Size C module is based on 13th Gen Intel® Core™ desktop processor. It features Intel’s advanced hybrid architecture (with up to 8 P-cores and 16 E-cores) along with 16 PCIe Gen5 that provide superior performance with fewer lanes than its predecessors, allowing for simplified designs and reduced time to market to drive various AIoT deployments.
-
Product
6U CompactPCI Enclosures & Systems
-
1~9U CompactPCI chassis for 6U CompactPCI boards , most of which are with front/rear panel I/O, H.110 CT bus and redundant power supplies.
-
Product
3U CompactPCI® Subsystem with 8-slot Backplane and 1 + 1 CompactPCI® Redundant Power Modules
cPCIS-2632 Series
Backplane
- 3U CompactPCI® backplane with seven peripheral slots and one system slot- Temperature, voltage, and fan monitoring LEDs- Supports current sharing on +5 V, +3.3 V, and +12 V- 1 + 1 hot swappable 250 W + 250 W CompactPCI® power supplies- PICMG® 2.11 47-pin power interface- Hot-swappable cooling fans & filter
Parent
-
Chroma Group
The focal points of Chroma are tests and measurements on power electronics, passive components, electrical safety, video & color, LCD/LCM, automotive electronics, and semiconductor industries. More importantly, Chroma also drives itself toward clean technology by providing testing solutions in photovoltaic, LED, Li-battery, power battery pack, electric vehicles and other emerging new eco-industries. After sustained investment and expansion for nearly 30 years, the operation of Chroma Group has covered most of the precision tests and measurements for various professional fields to provide turnkey test and automation solutions, also stridden across the areas of semiconductor materials, LED Chip & semiconductor inspection service, industrial PC, commercial LED/LCD monitor, electric scooter and electric vehicle powertrain system. Rooted in Taiwan with global arrangement, Chroma Group has setup operations in America, Europe, Mainland China and East Asia along with dealers all over the major cities in the world to provide convenient and fast services for customers everywhere.
Siblings
-
Chroma ATE Inc.
Founded in 1984, Chroma ATE Inc. is a world leading supplier of precision test and measurement instrumentation, automated test systems, intelligent manufacturing systems, and test & automation turnkey solutions marketed globally under the brand name "Chroma". Significant markets served by Chroma include semiconductors, photonics, LED, photovoltaics, video & color, flat panel displays, power electronics, passive components, electrical safety, green batteries, electric vehicles, thermoelectrics, automated optical inspection and intelligent manufacturing systems for ICT and cleantech industries.
Siblings
-
Chroma Systems Solutions, Inc.
From power conversion to battery to electrical safety, our test systems will maximize your time, improve your validation process, increase your throughput and help the world’s leading R&D labs with testing applications as diverse as your requirements.
Siblings
-
Adivic RF Test & Measurement
Huihong Technology specializes in RF technology for nearly 20 years. It is a leading manufacturer of RF measurement instruments in Taiwan, providing the required solutions for RF RF recording and playback, semiconductor RF signal testing, and GPS signal simulation.
Siblings
-
Camtek Intelligent Imaging
Camtek is a leading developer and manufacturer of high-end inspection inspection and metrology equipment for the semiconductor industry.
Siblings
-
Environmental Stress Systems, Inc.
Product line has expanded to provide an array of environmental stress screening products for the commercial, automotive, aerospace and military electronics industries.
Related
-
Virginia Panel Corporation
Virginia Panel Corporation (VPC) provides VPC provides Interconnect Solutions that enable simultaneous connection of multiple test and measurement signal types through one modular interface. Designed to accommodate signal, power, RF, thermocouple, pneumatic/vacuum, and fiber optic connector modules in multiple configurations, VPC’s innovative products meet the demands of test & measurement interconnect requirements.
