Qualification
fulfills an absolute condition.
See Also: Performance Testing, Validation, Characterization
-
product
Extensive Qualification & Test
Quality and reliability of the battery pack design starts with proper cell selection. Ensuring the battery pack is well matched to the host equipment is often overlooked or not given sufficient priority until performance and/or supply problems occur. Proper cell selection is key and requires much more than checking dimensions and capacity. Designers need to consider loading, environment, shelf life, and a number of other factors specific to the application.
-
product
Qualification Testing
Teledyne Storm Microwave ensures your design specifications are met by conducting in-house testing at all production phases. This comprehensive qualification process guarantees high-quality performance and reliability in every cable assembly, meeting the stringent requirements of your application.
-
product
Desktop Meter Qualification Board
2199
Providing complete capabilities for evaluating meters and communications performance, TESCO’s Desktop Meter Qualification Board (Catalog No. 2199) can generate any voltage and load conditions the meter may encounter in the field. Apply non-sinusoidal voltages with complex load waveforms. Perform disconnect tests and reconnect tests without having to worry about being able to drive the meter’s switches.
-
product
Qualification and Quality Control Tests
Techsquare
New IEC standards, IEC 60034-18-41 and IEC 60034-18-42, have been issued to define the procedures for testing partial discharge inception voltage and the long-term performance (endurance) of Type I and Type II insulation systems used in rotating machines fed from voltage converters. Voltage impulse generators are required at least to test turn insulation, but they would be recommended for any testing under power electronics supply because of their capability to simulate the real electrical stress conditions. More generally, any type of electrical insulation system when subject to impulsive voltage waveform during life should be carefully evaluated in terms of partial discharge and endurance behaviour. This is why voltage impulse generators able to provide impulses with controlled amplitude and frequency are needed to face this new testing challenge.
-
product
Qualification Hardware & Sockets
Reltech Limited holds over 35 years’ experience in the design and manufacture of all types of qualification test hardware. Our advanced technology products include: HTOL Boards (Mother and Daughter cards) Burn-In Boards HAST Boards THB (humidity) Boards Burn-In Modules and frames Dynamic Driver cards (Digital, Analogue and Mixed signal) Back Planes Voltage regulator cards Custom electro-mechanical assemblies DUT Cassettes and test Fixtures
-
product
Software
Tool Qualification Solutions
Many regulatory agencies require that any software tool used to tailor the safety life-cycle must be qualified to ensure that the tool is functioning correctly for the intended purpose. Genuen’s Tool Qualification Kits (TQK) provide a solid foundation for achieving formal qualifications used as part of your development process in highly regulated industries such as automotive, aerospace and medical.
-
product
Bluetooth LE Protocol Qualification Tester
conformanceHarmony
The conformanceHarmony LE Tester is a robust testing solution recognized by the Bluetooth SIG as a validated test platform, focused on the qualification testing of products to the Bluetooth low energy specification. It is an integrated software/hardware test platform for Bluetooth protocol qualification testing that provides:
-
product
Qualification Tester
LQ402
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 6 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 2 cabinets. One is for the electronic components with the primary measurement devices and the other one holds the 6 load boxes.
-
product
Low Voltage Differential Signaling (LVDS)
Available in QML-Q and QML-V processing flows, CAES LVDS solutions meet all of the stringent mechanical qualification requirements defined in MIL-PRF-38535.
-
product
Voltage Stabilizer
MS 7643
VSTAB is a voltage stabilizer, regulates the incoming supply +28V voltage into the required +15V. The electrical specifications meets MIL704 standard. Over load and short circuit protections are provided. Voltage stabilizer Module is a part of shipborne unit and it is meant for ensuring the power supply of the devices of this unit when fed from DC mains with nominal voltage of 28 V and variations of voltages from minimum 16V to maximum 32 V. The power consumption is 45 watts. The module is subjected to Qualification Tests as per MIL-STD-810G.
-
product
VDATS, Cable Assembly Kit, All-Inclusive
541139193
VDATS, Cable Assembly Kit, All-InclusiveTop-Level part number for VDATS cable assembly kit that includes 26 individual cable assembly part numbers and a quantity of 35 total cable assemblies. Requires special order qualification.
-
product
Semiconductor & Electronic Systems Test and Diagnostics Services
Reliability Test and Diagnostic services are offered to a wide range of customers that are active as Fabless Semiconductor or Integrated Device Manufacturers, automotive electronics supplier, Telecom and ICT application specialists, Industrial and Medical electronic system manufacturers or in Aerospace and Space applications. Independent high tech test and diagnostic service laboratory. IC and electronic module qualification. ESD and Latch Up testing. Design assessment by HALT/HASS. Failure and construction analysis.
-
product
Bluetooth RF Test System
FRVS
FRVS is recognized by the Bluetooth SIG as a validated test system for qualification testing of products to Bluetooth BR/EDR and low energy RF test specifications.
-
product
Microelectronics Test & Engineering Services
EAG's Microelectronics Test and Engineering lab network provides semiconductor and electronics design firms worldwide with test, debug, and early engineering support to help you with new product introduction. We actively service a broad range of semiconductor and electronics companies worldwide. Services include ATE testing, Reliability testing and qualification, ESD testing, Failure Analysis, FIB Circuit Edit and Debug. for both ICs and systems
-
product
Automatic Online Flatness and Surface Appearance System
UltraSort200
The UltraSort continues our 25 year tradition of providing metrology solutions to semiconductor wafer manufacturers. Designed for volume wafer production, this automated system offers superior performance in rapid, repeatable, accurate, noncontact qualification of silicon and alternative substrate wafers.
-
product
Semiconductor Memory Tester
T5851
Advantest Corporation has introduced the T5851 system, designed to provide a cost-effective test solution for high-performance universal flash storage (UFS) devices and PCIe BGA solid-state drives (SSDs) memory ICs in high demand by makers of low-power, mobile applications such as smart phones, tablets and ultra-portable laptops. The flexible T5851 tester is available in both production and engineering models. This allows the system to be used for reliability and qualification testing as well as test-program development or, when equipped with an automated component handler such as Advantest''''s M6242, high-volume production. As a fully integrated, system-level test solution, the T5851 provides multi-protocol support in one tool while its tester-per-DUT architecture and proprietary hardware accelerator allow it to achieve industry-leading test times.
-
product
HIL/V&V Solutions
SPHEREA designs test systems derived from our modular platform for V&V applications, for the whole development chain, from design to qualification
-
product
Three Phase Meter Qualification Board
MQB3
Apply true three phase voltage and current to electric meters, enabling them to be tested under all possible conditions that may be encountered in the field with TESCO’s Three Phase Meter Qualification Board (MQB3).
-
product
Burn-In Test Sockets
The selection of the test socket is critical to the performance of a device during qualification testing where electrical bias and signals are applied. Key factors such as mechanical compatibility, operating temperature, ability to withstand high moisture levels, signal speed and lead inductance/capacitance all need to be taken into account when selecting the best socket for the test application.
-
product
HBM Verification Tester
HBM-VT
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
product
EMI Testing
Independent Testing Laboratories
ITL offers compliance and qualification testing for virtually any type of electronic product or system.
-
product
Meter Test Station
WECO 8000
The innovative WECO 8000 Meter Test Station is the first of its kind – a multi-position test board integrating meter qualification and accuracy. This versatile and economic test station is the solution for utilities needing the ability to switch between functional testing and accuracy testing. Separate multi-position test boards are no longer a necessity.
-
product
Electrical Probe Systems
INSTEC's Probe Systems offer an integrated solution for performing component-level electrical measurements over a wide temperature range.Compact Mini Probe Stages enable an existing inspection microscope or optical test setup to be converted easily into a precision temperature-controlled semiconductor testing and qualification station.Analytical probe stations are fully featured industry-standard platforms for all modern probing applications and testing.Benchtop Probe Stations provide the user with four independent electrical probes with X,Y,Z micropositioning for precise placement without opening the sample chamber.Highly configurable probe systems meet a range of requirements for atmospheric and temperature control, sample areas, and electrical measurements.
-
product
Qualification Tester
CableIQ
CableIQ qualification tester is the first cabling bandwidth tester for network technicians. This Ethernet network cable testergives even the most novice tech the vision to see what speeds existing cabling can support, quickly isolate cabling from network problems, and discover what is at the far end of any cable.
-
product
Evaporative Emissions Testing
GASERA ONE SHED
Evaporative losses from the fuel system are tested for vehicle certification. GASERA ONE SHED allows direct monitoring of evaporative emissions as part of the qualification testing procedures for vehicles. The GASERA ONE SHED’s photoacoustic technique is approved by the Environmental Protection Agency (EPA) and the California Air Resources Board (CARB).
-
product
PCB Connectors
CMD Series
Smiths Interconnect's versatile, high density CMD connector solution for board to board and wire to board with built in coding and keying as well as ESA qualification
-
product
Qualification Testing
Qualification testing is an important step in evaluating how well spacecraft and launch vehicles perform under severe loading conditions that occur during launch and operation. ATA has conducted acoustic and vibration qualification testing of numerous launch vehicles and spacecraft components.
-
product
Open Top BGA Sockets
Ironwood has the most comprehensive collection of open top BGA and QFN sockets that can be used for qualification application, silicon FIB testing, system development, thermal characterization, burn-in application, etc. IC socket can be defined as an electromechanical device, which provides removable interface between IC package and system circuit board with minimal effect on signal integrity. Typical packages include BGA, LGA, QFN, QFP, WLCSP, etc. Open top allows access to the top side of IC. Below is an example BGA socket that uses low cost elastomer contact technology.
-
product
General Purpose Piezoelectric Accelerometers
Piezoelectric accelerometers offer tremendous versatility for shock and vibration measurements. These rugged sensors can withstand adverse environmental conditions. A wide variety of configurations are available to support multiple application requirements. Specialty units are also available through mechanical or electrical design modifications or additional qualification testing.
-
product
Vibration Shaker and Control Amplifier
The performance of this Vibration System supports a wide variety of Vibration and Impact Shock capabilities, at g levels and weight-handling levels not previously available at Pacific. Applications include product development, design conformance, qualification, certification, and production screening to Military, Aerospace, Automotive, and Medical specifications.
