Parallel I/O

GPIB to Digital Interface Card with 128 HD Digital I/O lines. ...more

Serial to Parallel Interface board with 40 Digital I/O Lines and RS-232 or RS-422/RS-485 serial inerface. Small 4.5 x 5.5 inch (114 x 140 mm) Board - Connector down version mates with 4804 Relay Driver Board. ...more

A IEEE-488.2 GPIB to digital interface with 40 I/O lines that can be used to easily adapt devices with digital signals to the IEEE-488/GPIB/HP-IP bus. Signal monitor feature allows the 4803 to detect signal changes on 15 inputs. High-current drivers and input pullup resistors. Drives more devices, longer lines and inputs CMOS signals or switch ...more

Model 4823B GPIB to Parallel Digital Interface Board provides 56 parallel I/O signals with same pinouts as ICS's older 4823A card. On-card header connects to ICS's GPIB Connector/Address Switch Assemblies. Download the 4323B data sheet as a PDF file. ...more

The PCI338 provides eight relays for computer controlled voltage-free switching. The switching contacts of each relay are available on the 25 pole D-sub connector. The relays are controlled by the Z8536 parallel I/O controller. An external input is used as an emergency shut-off. If it is activated, all relay contacts will immediately return to ...more

This FPDP PMC is the second generation high speed digital parallel input output PMC module from VMETRO. The DPIO2 is built to supports the transfer speed requirements imposed by the FPDP II protocol. ...more

The PCI338 provides eight relays for computer controlled voltage-free switching. The switching contacts of each relay are available on the 25 pole D-sub connector. The relays are controlled by the Z8536 parallel I/O controller. An external input is used as an emergency shut-off. If it is activated, all relay contacts will immediately return to ...more

The M318 Centronics Parallel Controller M-module is based on the Z8536 CIO. It is capable of reading and writing 16 binary signals and can be programmed to generate interrupts when detecting transitions of the individual inputs. The M318 can be used as an industry standard Centronics interface, or as a 16-bit parallel I/O controller. Used as a ...more

Cable can be used with EE301-I2C or EE301-DCMI Model Numbers only. Cable + Power for Loads & Control Modules / Connects to a PC Parallel Port / Supports (2) Electronics Loads & Control Modules / 6' Power cable & 5' Data cable  ...more

  The CPCI338 provides eight relays for computer controlled voltage-free switching. The switching contacts of each relay are available on the 25 pole sub-D connector at the front of the card. The relays are controlled by the Z8536 Parallel I/O Controller. An external input is used as an emergency shut-off. If it is activated, all relay contact ...more

Parallel Digital I/O Module. Can target successive data blocks to specific processor boards. Two or three modules can be cascaded for decimating filtering or data reduction ...more

Compact yet expandable architecture can accommodate over 400 channels of analog, digital, and frequency I/O. Communication with PC via RS-232, parallel port, modem, or by transporting a PC-Card; optional RS-422 interface  ...more

The CVXI-1149.1/616 combines a CVXI-1149.1 type JTAG / boundary-scan controller with a 616 channel digital I/O parallel tester. These 616 I/O channels can be used to add control and visibility to connectors, traces, and logic that is otherwise untestable using traditional boundary-scan techniques. The digital channels are accessible through a ...more

VP7 is a 6U Intel Pentium III or Celeron Processor VMEbus embedded computer. Features low power mobile CPUs from 500 to 1000MHz. The VP7 has front and rear I/O, up to 512MB SDRAM and 10/100 Mbit Fast Ethernet. LCD interface and extended temperature range of up to -40?C to +70?C. Four serial channels, parallel port and two USB ports ...more

High-Speed Pattern I/O and Handshaking - high-speed, 32-bit, parallel digital I/O interface. It performs pattern I/O and high-speed data transfer using a wide range of handshaking protocols at speeds up to 80 MB/s. ...more

96-bit parallel digital I/O module ...more

96-bit parallel digital I/O board for computers with PCI - 96 Ch, 5 V, 2.5 mA ...more

High-speed, 32-bit, parallel digital I/O interface for ISA - Pattern I/O and Handshaking ...more

High-Speed Pattern I/O and Handshaking (DIO-32HS) - high-speed, 32-bit, parallel digital I/O interface for PCI ...more

96-bit parallel digital I/O device for computers with the universal serial bus (USB) ...more

High-speed, 32-bit, parallel digital I/O interface for PCMCIA ...more

The T6577 is an SoC test system offering support for a maximum of 1024 logic and/or I/O channels. It can perform parallel test (OS parallel test) of up to 32 devices, and allows an exceptional range of parallel test functionality, such as flexible pin assignments and testing odd numbers of devices. It will greatly contribute to lowering the cos ...more

96-bit parallel digital I/O device for computers with the universal serial bus (USB) ...more

48-bit, parallel, isolated digital I/O board for PCI ...more

High-speed, 32-bit, parallel digital I/O interface.It incorporates the National Instruments DAQ-DIO ASIC, a 32-bit general-purpose digital I/O interface specifically designed to deliver high performance on plug-in digital I/O boards ...more