Network Interfaces

NuStreams chassis NuStreams-600i is an ideal test beds for lab design, troubleshooting and mass production test of network products. Support 10G Ethernet, Gigabit Ethernet, 10/100 Mbps Ethernet, NuStreams-600i provides various interface for different test requirement. ...more

The M360 CAN bus Controller is an integrated standalone controller for the Controller Area Network (CAN) with an M Module interface. CAN is used within the automotive and general industrial environments. ...more

1. 7’’ LCD touch screen easy to handle, graphic interface friendly use. 2. Advanced 7 test functions. 3. Test results pass/fail indication, LAN cable problems and faults displaying at a glance. 4. Complete verify test upstream/downstream rate, simulation modem and STB, PING test. 5. Copper wire quality test DMM, resistance fault test, longitudinal ...more

Anue CPRI Signal Delay Network Emulators simulate the impairments that can occur on a CPRI link. Like all Anue emulators it is supported by a flexible hardware platform that enables very accurate and highly repeatable testing and includes automation capabilities to increase testing efficiency. The CPRI Signal Delay Network Emulator can emulate ...more

The AVT-717 provides a UBP interface that was designed for engineering and test applications. It also supports all CAN versions up to and including 2.0B. Additionally, the AVT-717 supports both two-wire and single wire versions of CAN (GM’s Single Wire CAN). The baud rate and other network parameters are fully programmable. The AVT-717 UBP & CAN in ...more

The model AVT-418 is an Ethernet Interface between a host PC and most of the automotive network protocols used by modules and vehicles now in production. The AVT-418 Interface supports all of these different automotive network protocols: • CAN; 2-wire (CAN-C or ISO 11898) - Ford Motor Company approved. • CAN; 2-wire (CAN-B or ISO 11519). • CAN; Sin ...more

The AVT-718 Multiple Interface is a single unit solution for communicating with all of the most popular network protocols found in-use today or destined to be found in tomorrow’s vehicles. It is a complete solution, with no additional boards or modules to buy. The AVT-718 supports the following automotive network protocols: • CAN (2-wire and GM sin ...more

The AVT-716 Multiple Interface is a single unit solution for communicating with many of the network protocols found in-use today or destined to be found in tomorrow’s vehicles.The AVT-716 hardware revision “E” supports the following automotive network protocols: • J1850 VPW • Keyword Protocol 2000 (ISO 14230) • J1850 PWM • GM’s ALDL (8192 UART) • I ...more

The FC2021 provides a quick and easy way of allowing X.21 copper based equipment to interface and communicate over fibre optic circuits. The FC2021 can be used as a straight forward fibre optic line driver. The unit can be set to operate at speeds from 64kb/s to 2048kb/s in steps of 64kb/s. The FC2021 can also be used to onward link an X.21 net ...more

The FIS Deluxe Mini OTDR offers powerful testing capabilities for all types of optical networks. It is a compact and durable instrument with an intuitive user interface that?s suitable for indoor or outdoor operation. The power and features are designed to suit both experienced users as well as new optical technicians. The simple one button Aut ...more

The Ranger HRC is a high-resolution mid-wave thermal imaging system built around a large format 640x480 array and a choice of powerful continuous-zoom telescopes. While the HRC is available in its standalone, environmentally hardened enclosure, it can also include and optional high-magnification CCD-TV camera, laser rangefinder, Digital Magnetic Co ...more

These modules provide an isolated Ethernet network interface for twelve discrete input and/or output channels. The outputs provide direct on/off, high/low, or open/close control of industrial devices. ...more

With even higher performance and expanded capacity range of 50W to 37kW. The MR-J2S is complimented by an outstanding family of servo motors all of which utilize an absolute 131,072 pulses per revolution encoder as standard. Other distinguishing features include higher frequency response to 550 Hz. The ability to accept pulse commands up to 50 ...more

The DC3021 is a basic PCM converter unit which provides a conversion from either a BNC or RJ45 interfaced network to a standard X.21 interface presented on a 15 way ?D? type socket. It is simple to fit and there are no internal options to set as the unit is designed to only function with a PTT supplied network, which will provide the timing. ...more

These modules interface high-level analog input signals to an Ethernet control network. A high-performance design ensures reliable measurements and dependable operation. ...more

The Ballard AFDX family of products interfaces various computer platforms with Ethernet based aircraft data networks. They enable computers with PCI, cPCI, or PMC expansion slots to receive and transmit data over an Avionics Full Duplex Switched Ethernet (AFDX) network. ...more

Upgrade your outdated, hard-to-maintain software by adding network connectivity, advanced analysis and reporting, and user-friendly graphical user interfaces to improve reliability, performance, and ease-of-use. ...more

The LU9073 is a generic PCM diagnostic unit which when fitted between a network interface and the user's equipment allows a network loop to be applied remotely. It is simple to fit and normally no internal options need changing  ...more

The OmniBusBox enables computers and networks to interface with up to four MIL-STD-1553 dual-redundant databuses or a combination of MIL-STD-1553 with other protocols via Ethernet or USB. Applications for the OmniBusBox include simulation, monitoring, and testing of avionics equipment and systems. ...more

FEATURES: DataSpy® Status Display; Implements Low Cost LAN; Supports 32 Users; Uses Single Twisted Pair; External DTE/DCE Switch; Programmable Contention; Selectable Termination. The Model 366 allows interfacing RS-232 based equipment with networks/equipment using RS-485. ...more

These modules provide an isolated Ethernet network interface for up to six input channels. Differential inputs eliminate ground noise and each terminal block includes a cold junction compensation (CJC) sensor for more precise temperature measurements. ...more

ACTIVU is an ISDN Layer 1 simulator which aims at testing network equipment designed to be inserted at the ISDN U interface as Network Termination (NT1), Line Termination cards (LT), U repeaters, Pairgain systems, multiplexers and routers. ACTIVU is able to simulate and to monitor all the Layer 1 events from the network side (LT simulation) and fro ...more

Super CAN Analysis Tool 2 (S-CAT2) package is now available in two additional versions: one offers an PCMCIA slot, the other offers an enclosed wireless Ethernet interface. Featuring our high-end analyzer, Hercules, and compact S-CAT2 hardware, this package is designed to support advanced communication with in-vehicle networks for use in a variety ...more

hese modules interface high-level analog input signals to an Ethernet network. A high-performance design ensures reliable measurements and dependable operation. ...more

With even higher performance and expanded capacity range of 500W to 110kW. The MR-J2S is complimented by an outstanding family of servo motors all of which utilize an absolute 131,072 pulses per revolution encoder as standard. Other distinguishing features include higher frequency response to 550 Hz. The ability to accept pulse commands up to ...more