Analog Data Acquisition

APCI-3001-16 Analog Input Board, 16 Isolated Channels.16 single-ended or 8 differential inputs. 12-bit resolution. Isolation 500 V. 100 kHz sample rate. 8 isolated digital I/O, 24 V. Onboard FIFO buffers. PCI DMA access. ...more

APCI-3120-16-8 16 Single Ended or 8 Differential input channel, 8 Analog Output Channels. Optical isolation 500 V16 SE or 8 diff. inputs. Data transfer rate: 100 kHz. 16-bit resolution. 8 analog output channels. Data transfer rate:30 kHz. 14-bit resolution. Output voltage: 0-10 V, ±10 V, (set through software). Each output has its own ground l ...more

The C387 is a single-width, 6U, CompactPCI module with up to 256 digital input/output channels. The C387 base board supports 128 channels of TTL I/O. Four mezzanine card sites can be populated with other forms of digital I/O including isolated input, isolated output, relay output, AC switch output or differential I/O. The mezzanine card concep ...more

The CP266 is a single-width, 6U, CompactPCI module with 32 or 64, 16-bit analog output channels. These independent analog channels provide ±10 V full-scale outputs. The channel update rate is 2ms, and each output is accurate to ±1mV. The power-up state of the analog outputs can be set to independent user-defined values. Paired output signals a ...more

The KPCI-1801HC/1802HC multifunction data acquisition boards combine high performance with high channel capacity. They make it simple to gather analog data, read and output digital signals, provide analog stimulus, and much more. Both boards provide 32 differential or 64 single-ended inputs and two analog outputs. The KPCI-1801HC offers softwa ...more

GPIB Data Acquisition and Control Board with 4 Analog Outputs, 6 Analog Inputs, 32 Digital I/O, 6 Relay Drivers, and 4 Thermocouple Inputs ...more

The Model 4867 GPIB Data Acquisition and Control Module provides analog and digital signals for controlling virtually any kind of a device and the capability to read back analog voltages, digital signals andtemperatures. ...more

Serial Data Acquisition and Control Board. Provides Analog I/O, Digital I/O, Relay Driver Outputs and Temperature Measurements. RS-232, RS-422 and RS-485 Serial I/O includes network address and network packet modes. ...more

Serial Data Acquisition and Control Minibox. Provides Analog I/O, Digital I/O, Relay Driver Outputs and Temperature Measurements. RS-232 and RS-485 Serial interface provides GPIB functionality over a serial link. ...more

Your portable USB connection for analog and digital I/O. The USB-4700 series are true plug and play data acquisition modules. USB-4711 *8 Digital I/O * Analog Output 2 (12 bit). * Sampling rate up to 100kS/s. * One 32-bit counter. Connect to sensors with any USB enabled PC. ...more

DATAMAX DTX-9R is a state-of-the-art Windows 2000 based analog instrumentation recorder designed to replace traditional tape based data recorders. Using the latest technology, DATAMAX DTX-9R eliminates the time consuming methods of the past with a single precision instrument that will replace a tape recorder, data acquisition system, and monit ...more

The DP-VXI-4017 is a VXI based 80 Channel Relay Multiplexer constructed using ‘2 Form A’ (DPST) relays with channel-to-channel isolation of 220V. It is widely used in Automatic Test Equipments, Analog Signal Routing and Data Acquisition systems. It features 80 differential channels having switching capability of current, voltage and resistance meas ...more

The V581 is a single-width, C-size, register-based, VXIbus module that contains 68 two-pole, double-throw relays for calibrating individual analog channels in data acquisition systems. Wiring from the transducers is brought in to the 50P or 68P High Density Connectors (P3 and P4) on the front panel. Two additional High Density Connectors (P5 and P6 ...more

A traditional scheme of superheterodyne receiver with double frequency conversion is used in the radiometer. At the output i t produces an analogue signal within 10 V range proportional to the radiation power. The device operates under a completely automated system of control and data acquisition ...more

The PCI-1711 is a multi-function data acquisition card for the PCI bus. This card provides multiple measurement and control functions. ...more

The 232SPDA module is similar to B&B SDA data acquisition modules, with the addition of analog outputs. You may output as well as read analog voltage. Just 4 commands control the module. Model 232SPDA provides 7 channels of 12-bit A/D inputs, 2 digital input channels, 1 digital output channel and 4 channels of 8-bit D/A outputs. ...more

The MSXB 065 Signal Conditioning Expansion Board provides filtered analog signal conditioning for voltage signals for Data Acquisition Processor systems. Each board has differential inputs; jumper-selectable simultaneous sampling; jumper-selectable gains of 1, 5, and 25; fourth-order anti-alias filters, cutoff frequencies from 100 Hz to 50 kHz. ...more

The PP139 data acquisition, processing and recording platform is capable to digitize up to 16 analog inputs with a sampling frequency of 65MHz maximum. This highly scalable system can host up to 4 Virtex-4 SX35 devices for real-time processing and offers up to 1600Gbytes storage capability. An Ethernet connection to a host computer enables user ...more

The DAP 5200a model brings many more real-time data acquisition and control applications within the scope of Windows systems. Its onboard 400 MHz processor substantially increases the real-time processing power of the top end of the DAP line. Real-time processing functions include smoothing, filtering, FFT, PID control, and responding to alarm ...more

The Model 3568 is a double-width CAMAC module containing 32 two-pole, double throw relays for calibrating individual analog channels in data acquisition systems. ...more

The Microstar Laboratories Analog Backplane Interface Board, part number MSXB 029, interfaces the Analog Backplane with a Data Acquisition Processor. The Analog Backplane Interface Board must be installed in the Analog Backplane to connect the backplane to a Data Acquisition Processor. ...more

The ADAM series modules are compact, versatile sensor-to-computer interface units designed specifically for reliable operation in harsh environments. Their built-in microprocessors, encased in rugged industrial grade plastic, independently provide intelligent signal conditioning, analog I/O and digital I/O via RS-485 serial or Ethernet communi ...more

ScopeLogic - complete data acquisition system - consists of Digital Oscilloscope and Logic Analyser. This small instrument is making the accurate analysis of complex analog-digital signals possible - thanks to simultaneous sampling finding relationship between these signals is easy. The user is able to simultaneous use 16 digital channels and 2 ana ...more

Presys 4000 systems provide easily configured analog and digital data acquisition, and analog and digital data output, in a compact instrumentation package. The basic system provides multi-channel A/D conversion and D/A conversion by utilizing ADC (and DAC) modules on a one per channel basis. ...more

The MSXB 032 Analog Output Expansion Board converts digital inputs from a Data Acquisition Processor into four separate analog outputs. Up to 16 Analog Output Expansion Boards can be connected to a Data Acquisition Processor for a maximum expansion of 64 analog output channels. The MSXB 032 is compatible with Microstar Laboratories Industrial ...more