-
product
System Level Test and Burn-in Solutions
System Level Test (SLT) is a paradigm shift from traditional structural and functional testing. The device is tested in a complete, integrated system to evaluate its compliance against specified requirements. The system approach allows for higher and more cost-effective test coverage especially for multi-function and non-deterministic devices. It also brings new integration and test challenges like: ..Designing test fixtures on Burn-in Boards with system components ...
-
product
Fibre Channel Testing
The storage area network (SAN), created in response to enterprises' data storage needs, is a grouping of interconnected devices and servers that use a common communication infrastructure, combining and capitalizing on the best of both the storage and network worlds. The protocol used for this infrastructure is Fibre Channel.
-
product
Multifunction Meter for Electrical Installations
AMPI-530
Measurement of short-circuit loop ; Testing of differential, general and selective protections for differential current ; Measurement of insulation resistance ; Up to 10GΩ ; Voltages: 50 V, 100 V, 250 V, 500 V, 1000 V ; Measurement of earth resistance ; Bi-directional continuity test on PE cables, phase sequence ; Measurement and recording of voltage, frequency, alternating current, cosϕ, power, harmonics and THD
-
product
Magnet Testing
magtrack
The magtrack makes it possible to detect the absolute 3D position in space as well as the orientation of a magnetically marked particle over a course of time. The magtrack system is modular and can therefore be adapted to any installation and system.
-
product
LXI Reed Relay Matrix - Single 64x8 Plugin, No Direct Y Access, 6 Analog Buses
65-223-102
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
-
product
Universal Material Testing Machine Tensile Compressive Fatigue Strength
Vexus MT20
Sinowon Innovation Metrology Manufacture Ltd.
Vexus MT20 series of material testing machine is designed in double-column with maximum testing force 20KN, it is able to make the material testing about tensile, compression, bending, shearing, bonding strength, peeling, tearing, etc, it is applied to test the material such as rubber, plastic, leather, metal, nylon line, fabric, paper, aviation, packaging, construction, petrifaction, electrician, vehicle and other materials.
-
product
Rational Performance Tester
Rational Performance Tester is a performance testing tool used to identify the presence and cause of system performance bottlenecks. Provides testers with automated performance testing capabilities to validate the scalability of web and server based applications.
-
product
CRM Testing Services
If you are looking for truly comprehensive testing carried out by experts with years of experience at a low cost and no time lag, QA Mentor is your answer!
-
product
Software Package
System Software 3
BAUR Prüf- und Messtechnik GmbH
The BAUR system software is a cable testing, cable diagnostics and cable fault location package. It enables efficient monitoring of the condition of cable networks in combination with BAUR cable fault location, testing and diagnostics systems.
-
product
Conformance Test Systems
With an established market leadership position in GCF and PTCRB approvals for LTE-Advanced and all leading-edge technologies, Anritsu continues expanding its number of test case validations in GCF and PTCRB for Protocol, RF and RRM conformance testing. With increasing complexity of wireless technologies, Anritsu Conformance Test systems provide easy-to-use control software to maximize testing efficiency.
-
product
Testing and Configuration Tools
DNP3 Forge
Create/Edit DNP3 XML Device Profiles (included in free version).Supports January 2010, July 2012, November 2013, and November 2014 versions of the DNP3 XML Device Profile Schema.Allows the version of a profile to be changed.Displays DNP3 Device Profile contents in an easy to navigate and searchable tree.Displays properties of selected element with details.
-
product
Portable Water Testing Field Kits
Aquagenx portable water testing field kits combine our Compartment Bag Test (CBT) E. coli Kit with key chemical and geophysical water quality parameters and testing equipment. Each field kit contains equipment and consumables for 100 samples.
-
product
SRJ (for IBP sensors)
The MEDTEQ SRJ is a test jig to measuring the step response of IBP sensors, which can assist in testing compliance with IEC 60601-2-34 frequency response. It is also suitable for manufacturers or test labs wanting to access the raw pressure waveforms via an oscilloscope.
-
product
Time Domain Reflectometer / TDR
For testing cables and interconnects, we offer the ideal tool: A time domain reflectometer (TDR). Time domain reflectometry/transmission can be used to test network return loss (S11), propagation loss (S21), and crosstalk.Moreover, it can provide the impedance profile of an electrical channel. MultiLane supplies semi-automated solutions for the testing of direct-attach cables and TIAs.
-
product
MEDTEQ Testing Services
The MEDTEQ facility has a medium range of test equipment as detailed below for testing to various standards. MEDTEQ reports have the equivalent status of a manufacturer's report, which is acceptable under medical device regulations for many regions, such as US, Europe, Canada and Australia. The reports contain a cover page, general description, sample identification (including photos), clause list (core evaluation), and test data. Unlike CB scheme reports, the test data section is a self contain...show more -
product
Ethernet
Ethernet, arguably the most common communication protocol on the planet, continues to spread into new markets and incorporates new protocols; it presents today’s Ethernet engineers with host of new test and validation challenges. Specifically, the increasing adoption of lossless Ethernet standards like FCoE, RoCE, and NVMf and increases in the line-rates of Ethernet from 10GbE and soon to 100Gb/s to name a few.These new physical and logical communications standards have exposed legacy test tools...show more -
product
DiodeTester
FECPLS500
Frothingham Electronics Corporation
The PLS500 automatic tester is designed primarily to do SURGE testing either as single pulses or with Forward and Reverse bias, according to methods 4066-1 or 4066-2. In addition, it can also test VF with rectangular pulses and THERMAL RESPONSE either in DVF (mV) or degrees per watt. All three test types may be performed in a single test program.
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 3Ω To 52.4kΩ
50-298-033
The 50-298-033 is a high density programmable resistor card with 9 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Striplines / TEM-Cells
Open, unsymmetrical 50 Ω stripline for automotive immunity testing of components.
-
product
WHQL testing
The purpose of Microsoft's Windows Hardware Quality Labs is to certify that a device is compatible with Microsoft operating systems. Companies whose devices pass this series of tests are qualified to display the Microsoft Windows logos and can be listed on Microsoft's Hardware Compatibility List (HCL), www.microsoft.com/hcl/.
-
product
SCSI CABLE TESTER
ST123
Continuity tests alone are not sufficient to qualify SCSI cable assemblies. Proper testing of SCSI cables must include a test for correct connection of twisted pairs and shielding. Continuity tests check only that wires are making connections on both ends of a cable.Twisted pairs in the cable must be matched with the correct SCSI signal pairs - otherwise, it is possible to have a SCSI signal (signal and ground pair) placed on wires that are not in the same physical twisted pair (see diagram at right). This will cause crosstalk with resultant SCSI errors.
-
product
Portable Hardness Tester
Handheld Hardness Testers
Handheld Hardness Testers are ideal hardness testing tools where large samples, which cannot be brought to a traditional tabletop hardness tester, or specimens with hard to access areas are to be tested. A wide variety of the portable hardness testers, offered by Qualitest ensure that we recommend the most suitable model for your application. The extensive selection of our handheld hardness testers is available from low-cost economy models up to advanced models coming with more features. These models can measure the hardness of your materials in Rockwell, Superficial Rockwell, Brinell, Vickers, Webster, Barcol scales and often conversions can be done.
-
product
ICT/FCT Probes
During in-circuit testing (ICT), each component of an electronic assembly is checked for faults. Short circuits, interruptions, soldering or component faults are detected and assemblies are rejected according to a go/no-go test.During functional testing (FCT), the assemblies are tested completely or in partial areas for the intended operation. The function test of the modules is carried out in the end application or in an environment that simulates the end application.
-
product
Coupling Decoupling Network for Conducted Common Mode Immunity Testing According to IEC 61000-4-6
CDN
The CDN M5 is intended to inject common mode disturbance signals to power supply of mains lines (unscreened) in the frequency range from 150KHz to 230MHz. A variety of calibration adapters and other accessories are available as an option. RF Standard connector: BNC type, AC socket 4mm safety bananas.
-
product
Deflection Gauge Extensometers
AMETEK Sensors, Test & Calibration
We supply a wide range of deflection gauge extensometers ideal for measuring deformation in three and four point bend tests and in compression testing applications.
-
product
Environmental Test Chambers
CSZ offers a large selection of environmental test chambers with quality construction and innovative technology, serving a variety of industries. Temperatures range as low as -84C (-120F) with high temperatures to +350C (+662F) and humidity ranges from 10% to 98% RH. Test chamber sizes range from small benchtop chambers for testing small components to full walk-in/drive-in rooms large enough to accommodate a semi-truck and trailer or larger.
-
product
9075 - 75 Module Solution
VPC rack mountable receivers like the 9075 meet the standards essential to support advanced mass interconnect requirements. The 9075 receiver is designed to accept the 9025, 9050, 9050 VXI, and 9075 ITA and can be adapted to accommodate vacuum or mechanical fixturing. Connector modules can be intermixed to create custom interfaces which are ideal for functional and system testing applications.
-
product
Glyphosate Testing Solutions
Glyphosate is a chemical herbicide used during cultivation of cereal grains, pulses, oilseeds, sugar beets and more.The International Agency for Research on Cancer (IARC) classified glyphosate as a Group 2B probable carcinogen in 2016. Since that time, at least 35 countries, regions and municipalities have moved to restrict or ban the use of glyphosate for commercial and noncommercial use.
-
-
product
IP Networking
We are the industry leader in IP Networking testing. We have a strong and wide-reaching industry reputation and participates in many industry organizations including the IETF, the IPv6 Forum, Open Networking Foundation and NetSecOPEN.
