Showing recent results 1216 - 1230 of 1268 products found.
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in chamber for Complex Salt Spray Test Relevant standards requirement1. Test Object: battery pack andsystem.2. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.3. The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water，Its concentration is (5 + 1)% (mass fraction).4. (35 ± 2) ℃, the measured pH value is between 6.5-7.2.5. Placed the test objects in the salt spray chamber for cycling test. Each cycling duration for 24h. Spray salt solution to the test object for 8 hours under the temperature of (35± 2) ℃ , remain for 16 hours. Between the forth and the fifth hour in one cycles should be according to test requirement in GB/T 28046.1-2011, test mode with 3.2.6. Total 6 cycles testing.7. Salt spray test is not necessary for the test objects being installed in passenger, luggage or cargo compartments.
-
MP-981/AP-981 - Ono Sokki
The MP-981 is a magneto-type detector using a hall element which is suitable for revolution (r/min) measurement from low speed to high speed.Magneto-type detectors use an internal hall element, a permanent magnet, DC amplifier, and voltage regulator and respond to flux, so that a rectangular wave form is derivable from much lower speed all the way though high speed.In addition, a signal indicator is provided in spite of the detector's compact design, making verification of operation and mounting position possible.Meanwhile, the AP-981 is the water and acid proof type, which conforms to Class ' of JIS C0920.
-
Darwin Chambers Company
Darwin Chambers Company’s NFPA, GSA, and NARA Directive 1571-compliant Archival Storage Chambers are engineered to provide maximum value, efficiency and conformance with all applicable standards and codes. Archival chambers provide environmental controls for storing records and materials (including paper documents and items with high fibrous content, various films, microfiche, and photographic materials) that require permanent protection for storage and preservation. Our high-performance systems are offered with nearly unlimited operational fail safes, includ- ing full system and control redundancy. In addition to keyed entry, numerous security options are also available, due to the often irreplaceable nature of the materials to be stored and preserved in this type of chamber. Our chambers are engineered to accommodate the loads and unique requirements of the specific materials to be stored, with industry-leading control and uniformity of both temperature and humidity variables. Design considerations include both functional and operational efficiencies and reliability, the safety and comfort of operating personnel, and the ongoing protection of the archived materials from fire, water, light degradation, pests, mold and natural contaminants, pollutants and other man- made threats.
-
Sun Test Systems Ltd.
Sun Test Systems develops and manufactures mobile test equipment for commercial and military aircraft and helicopters.The product range consists of:A complete line of hydraulic test equipment for every helicopter or aircraft size. This equipment is able to fully clean and regenerate the hydraulic oil of the airplane from air, water and particles during hydraulic test activities. By integrating these two functions our equipment saves maintenance time and reduces repair work because of less leakages of the hydraulic system etc.The multifunctional product line which combines a number of GSE functions, such as hydraulics, electricity, air, nitrogen, lighting, in one single unit.The other product lines with among other things a dye mix trolley for display teams and washing equipment for fuselages and engine cores.Our close cooperation with the German and British military forms the basis for the extensive product range. The products are designed and built to combine heavy use by the military with severe conditions encountered in desert areas or extreme cold. They have built up an extensive ‘proven track record’.
-
HMA-M - OPTOKON a.s.
The OPTOKON HMA-M connector series, a mini size „Expanded Beam“ connector is designed for connection of the nodes of harsh environmental network by the help of cables with optical fibers. The used expanded beam technology preservers all advantages of signals transmission through the optical lines in field harsh environmental conditions. Additionally to ruggedized optical networks the HMA-M is suited for a vast array of applications, like heavy industry connections, petrochemical application, broadcasting temporary optical lines. The innovative designs ensure its ability for deployment in the toughest environments where high performance and total reliability are critical. Benefiting from expanded beam technology the precision optical alignment system creates immunity from water, mud, dust oil and other contaminants. The HMA-M Hermaphroditic coupling eliminates the need for adaptors and male and female mating halves. Hermaphroditic housings allow for rapid deployment, creating low loss Singlemode and Multimode daisy chained links in a variety of planforms ranging from simplex fiber to a four fibers. The OPTOKON HMA-M is ideally suited for environmental extremities where low maintenance and quick repairability is necessary.
-
Alpha Moisture Systems
The key to the operation of Alpha Moisture Systems' Portable Analysers is the unique Desiccant Dry-Down Chamber. By keeping the sensor dry between tests, the special assembly of the head ensures that the instrument is always ready for immediate use. The head assembly consists of two chambers which have a telescopic action. When the head assembly is in the 'closed' or 'Dry-Down' position, the sensor is completely surrounded by desiccant, which absorbs the remaining water moisture from the sensor and hence it is dry and ready for use. The small space at the bottom of the test chamber enables the sample pipe to be purged before the test commences without wetting the sensor. By placing a finger over the outlet of the head, the sample pressure is able to open the test chamber automatically, exposing the sensor to the gas being tested and enabling accurate reading of moisture content in the sample gas. After each test the head assembly is closed by depressing the inner section so that the sensor will again be dried by the desiccant, leaving the sensor ready for use time and time again. The desiccant is kept in the inner chamber and is not exposed to ambient room air or the sample gas, therefore there is no need for frequent regeneration or replacement of the desiccant.
-
HMA-S - OPTOKON a.s.
The OPTOKON HMA-S connector series, a large size „Expanded Beam“ connector is designed for connection of the nodes of harsh environmental network by the help of cables with optical fibers. The used expanded beam technology preservers all advantages of signals transmission through the optical lines in field harsh environmental conditions. Additionally to ruggedized optical networks the HMA-S is suited for a vast array of applications, like heavy industry connections, petrochemical application, broadcasting temporary optical lines. The innovative designs ensure its ability for deployment in the toughest environments where high performance and total reliability are critical. Benefiting from expanded beam technology the precision optical alignment system creates immunity from water, mud, dust oil and other contaminants. The HMA-S Hermaphroditic coupling eliminates the need for adaptors and male and female mating halves. Hermaphroditic housings allow for rapid deployment, creating low loss Single mode and Multimode daisy chained links in a variety of planforms ranging from simplex fiber to a four fibers. The OPTOKON HMA-S is ideally suited for environmental extremities where low maintenance and quick repairability is necessary.
-
HMA-J - OPTOKON a.s.
The OPTOKON HMA-J connector series, a medium size „Expanded Beam“ connector is designed for connection of the nodes of harsh environmental network by the help of cables with optical fibers. The used expanded beam technology preservers all advantages of signals transmission through the optical lines in field harsh environmental conditions. Additionally to ruggedized optical networks the HMA-J is suited for a vast array of applications, like heavy industry connections, petrochemical application, broadcasting temporary optical lines. The innovative designs ensure its ability for deployment in the toughest environments where high performance and total reliability are critical. Benefiting from expanded beam technology the precision optical alignment system creates immunity from water, mud, dust oil and other contaminants. The HMA-J Hermaphroditic coupling eliminates the need for adaptors and male and female mating halves. Hermaphroditic housings allow for rapid deployment, creating low loss Singlemode and Multimode daisy chained links in a variety of planforms ranging from simplex fiber to a four fibers. The OPTOKON HMA-J is ideally suited for environmental extremities where low maintenance and quick repairability is necessary.
-
Solar Light Company Inc.
Solar Light’s NIST-Traceable PMA-Series Analog Sensors represent the pinnacle of accuracy, durability, and selection on the market today. Our sensors measure discrete bands of the electromagnetic spectrum from the UVA, UVB, UVA+B, UVC, Visible Light, and Infrared regions. Both narrow and broad bands are available, to fit any application, including germicidal applications, environmental probes, and sensors for biologically weighted spectra (such as the erythema and CIE action spectra.) Over 135 different sensors are available in a variety of packages to fit any environment, from indoor clean rooms to harsh locations outdoors to 100 meters under water. Please note that Solar Light offers both Digital Sensors and Analog Sensors in the PMA-Series lineup. Select these Analog Sensors if you don’t need a digital display output of the reading, if you will be connecting to your own datalogger, or if you plan to use a voltage source to provide excitation voltage to the sensor and a digital volt or amp meter to read and convert the results. Analog Sensors are typically used as process sensors that are permanently installed to provide ongoing information. Typical current draw is under 1mA. (By contrast, Digital models are typically used as discrete sensors that are portable and located to provide short term information.)
-
TE Connectivity Ltd.
A pressure sensor is a device that senses pressure and converts it into an electric signal where the amount depends upon the pressure applied. TE Connectivity (TE) designs and manufactures pressure sensors ranging from the sensing element to system packaging for harsh environments. We are an industry leader for our range of both standard and custom pressure sensors, from board level components to fully amplified and packaged transducers. Based on piezoresistive Micro-electromechanical systems (MEMS) and silicon strain gauge (Microfused, Krystal Bond) technology, our sensors measure everything from less than one inch of water column (<1.25 mbar) to 100K psi (7K bar).
-
PMA-Series - Solar Light Company Inc.
Solar Light’s NIST-Traceable PMA-Series Digital Sensors represent the pinnacle of accuracy, durability, and selection on the market today. Our sensors measure discrete bands of the electromagnetic spectrum from the UVA, UVB, UVA+B, UVC, Visible Light, and Infrared regions. Both narrow and broad bands are available to fit any application, including germicidal requirements, environmental probes, and sensors for biologically weighted spectra (such as the erythema and CIE action spectra.) Over 135 different sensors are available in a variety of packages to fit any environment, from indoor clean rooms to harsh locations outdoors to 100 meters under water. Please note that Solar Light offers both Digital Sensors and Analog Sensors in the PMA-Series lineup. Select these Digital Sensors if you prefer to plug into our PMA-Series Radiometers to read the output of the sensor on the meter’s display. Digital models are typically used as discrete sensors that are portable and located to provide short term information. (By contrast, please select Analog Sensors if you don’t need a digital display output of the reading, if you will be connecting to your own datalogger, or if you plan to use a voltage source to provide excitation voltage to the sensor and a digital volt or amp meter to read and convert the results. Analog Sensors are typically used as process sensors that are permanently installed to provide ongoing information.)
-
Dor Yang precision instrument (Shanghai) Co.,Ltd
1.Fully Automatic and All Metal Detectors - Your detector detects all kinds of metal objects. Unless you have set for some objects that you don’t want to detect.2.LCD – The LCD with light, it improve to identify the metal in night or caliginous outside. 3.Target Identity - The detected objects are shown on the LCD display. You can decide immediately if the objects worth to be recovered.4.Unwanted Target Elimination - You can set the detector not to respond to some objects.5.Unique Tone for Target - You don’t have to keep watching the LCD display, when an object is being detected, an unique tone corresponding to a target will generate. You may even searching when there is little or no light.6.No Clumsy Slack Cable - hidden search coil cable (connecting between control unit and search coil) avoid entangling and for ease of stem length adjustment.7.Headphone Jack - provided for headphone connection. Both stereo or mono headphone can be used.8.Volume Control - for adjusting the output volume to the loud speaker or headphone.9.Batteries Condition Indicator - shows the conditions of the batteries in the battery compartment.10.Waterproof Search Coil - lets you use the detector in the shallow water.11.Adjustable Stem - lets you adjust the detector’s length for comfortable use. The micro-plug that connects the search coil and the controller unit is made of metal which makes the plug more reliable.
-
Teledyne Marine Gavia ehf.
The GeoSwath Plus Sonar Module contains a wide-swath bathymetric sonar suitable for a range of survey and inspection tasks. The GeoSwath Plus is a 500kHz interferometric sonar, or phase detecting bathymetric sonar (PDBS) from Kongsberg GeoAcoustics. Boat-mounted GeoSwath sonars are used worldwide for high accuracy surveys including port and harbour navigation and environmental mapping: the Gavia’s GeoSwath module makes this capability available in a commercial AUV. The GeoSwath Plus offers: wide swath coverage of up to 12 times the AUV altitude when near the seabed; integrated bathymetry with simultaneous true digital side scan; high depth resolution suitable for IHO survey standards; as well as the accuracy and repeatability of a boat-mount hydrographic survey system. Like most of the survey-grade sensors on the Gavia AUV, the GeoSwath data is time-synchronised with the AUV master clock using the vehicle PPS/ZDA system. Benefits of the GeoSwath AUV module include ease of deployment, ease of use, reducing survey time, and the ability to take a 500kHz high-resolution sonar down to targets in 1000m of water. The GeoSwath Plus post-processing software (provided as standard with the system) allows a user to inspect and process the data, create and inspect digital terrain models, and create basic sonar mosaics. Several other commercial post-processing software packages are also available, please ask for details. Note that for best results the GeoSwath Module should be deployed with a direct-reading sound velocity sensor (option) in the Control Module, and one of the high-accuracy INS/DVL Navigation Modules for motion sensing.
-
LXinstruments GmbH
SCOEs and EGSEs by LXinstruments are used during test and validation of satellite assemblies and modules in aerospace applications. As an example, we implemented solar array simulators, battery simulators and high-power load racks for a German satellite manufacturer for testing satellite power supply systems. Due to the high power ratings, the systems are partially equipped with water cooling. Specialized switching modules were developed for switching DC currents at high voltage levels; these can be programmed with SCPI commands via Ethernet.Our modular OTP² functional test platform is ideally suited for implementing durable, reliable test systems, e. g. for in-flight entertainment applications. Since the OTP2 platform is based on open interfaces, it can be quickly and easily adapted to any required communication busses and ARINC interfaces.
-
HC-3 - Canden Products LLC
HC3- 3 cu.ft ENVIRONMENTAL CHAMBERTemperature range--4°C to 50°CTemperature uniformity--± 0.7°CThis is a 3 cu.ft laboratory incubator capable of performing in wide temperature range(4°c to 50°c) with precise temperature control over the entire range. The heating/chilling incubator can be used in wide range of application including;Protein crystal growthEnzyme reactions and deactivationsLigationsIncubating marine cultures below ambientCulture growth above, below or at ambientStoring DNA librariesChamber features all stainless steel interior and exterior construction with 2″ polyurethane CFC free insulation.Chamber feature a unique double shell-filled with commercial-grade polyurethane material for optimal insulation. Inlaid sealing ring and nylon latch for enhanced seal/performance. The chamber is made out of LLPDE material shell.The chamber comes with 12 molded slots. We provide 2 wire shelves with each chamber. Additional shelves are available for purchase. Shelves can support up to 25lbs distributed load. The Chamber comes with 2 hidden molded handles that enables users to move the chamber with ease. The chamber is also stackable without additional parts.Chamber uses thermoelectric assembly for heating and cooling. This type of cooling/heating system completely eliminates need for conventional refrigeration system and failures due to mechanical components such as compressors thereby drastically increasing the life expectancy of each chamber. Maintenance cost is also lowered by the thermoelectric/Peltier driven heating/cooling system. The chamber is quiet (less than 55dba) while in operation. Chamber temperature set points are tightly controlled using PID controller. Relative humidity set points are achieved via additive ultrasonic humidification. A humidifier is mounted on the back of the chamber. Refer to humidifier manual for maintenance and water line hook up.
