Voltage
The tension of an electromotive force.
-
product
Partial discharge measurement with remote wireless reading
PD-LT
The PD-LT allows online partial discharge detection on cable accessories such as cable head for safety and maintenance purposes.The PD-LT indicates the intensity of the partial discharges, converting the electrical charge units (pC) into decibels (dB). Thus the reading is kept as a simple intensity level indication, proportional to the probability of a fault's presence in the tested medium voltage accessory.The remote display gives a dB value of the probe's measurement. The dB value will vary along with the discharges indicators on the PD-LT probe. The measurement range is from 0 to 65dB and the display will show ''OL'' if the reading is over 65dB.
-
product
PXI/PXIe High Voltage Multiplexer, Hex 7-Channel, 1-Pole
40-321-103-HI
The 40-321-103-HI (PXI) and 42-321-103-HI (PXIe) are hex 7-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
5-Watt Broadband Transmitter
Loc3 5W
The 5-Watt broadband transmitter has selectable induction and direct connection frequencies from 98Hz to 200kHz, SD mode (Signal Direction), fault find and true resistance measurement up to 1 Mohm. The two inch by one-inch dot matrix display with LED backlight shows output current, connection type, volts, resistance, frequency, volume, battery condition and high voltage warnings.
-
product
PXI Attenuator Modules
Programmable RF Attenuators – accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices.Solid State Programmable RF Attenuators – available in triple or hex formats with bandwidths between 10MHz and 6GHz.High Voltage Attenuators – provide a convenient way of attenuating high voltage low frequency signals to levels that can be captured by other PXI devices without risk of damaging them.
-
product
DC to LVDT and DC to RVDT Converters
Computer Conversions Corporation
The SLVT Series are complete, low profile, continuously updating, single channel, Isolated Digital to LVDT Converters used to simulate the output of LVDT's (Linear velocity displacement transducers), RVDT's (Rotary...) and other phase/voltage sensitive AC devices. They provide a very precise linear AC voltage output proportionate to the magnitude of the input data, in or out of phase respective of the AC reference input as determined by the MSB of the input word (offset binary format).
-
product
PXI Monitored Multiplexer, Dual 32-Channel, 1-Pole
40-619-202
The 40-619-202 is a high density PXI 2 A multiplexer module in dual 32-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
product
Clamp type AC Current Sensor／with DC Voltage Output
RCT-18
MULTI MEASURING INSTRUMENTS Co., Ltd.
Leakage current measurements with DCV output for recorder. AC 0.1mA～100mA.
-
product
Online UPS
POWERPACK SE SERIES 1/2/3 kVA
Sine wave output and clean energy for computers and all sensitive equipments. Online UPS protects your equipments from all mains problems. Online UPS can operate with a wide voltage range so that battery power does not need to be used.
-
product
Clamp Meters
Sanwa Electric Instrument Co., Ltd
An electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.
-
product
High Voltage Probe
HVP-40M
*DC 40KV CAT II Pollution 2*600MΩ Impedance*25KV ± 2%, 40KV ± 3%*T.C. 200 ppm/oC*Positive Polarity only.*Resolution 1KV*Need not power.*CE, TUV GS, UL, CUL, IEC1010
-
product
Digital Ior Leakage Current Clamp Tester
MCL-400IR+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).
-
product
Electronic Counters
GR2-C Series
The GR2-C Series is a self-powered LCD Totalizer in small form. With a panel size of DIN 48 x 24mm, it is perfect for limited space installations. It is powered by a replaceable lithium battery that lasts approximately 7 years, no external power required. The GR2-C series is available in 7 digits with 8mm height figures with Front Reset or Remote reset options. Input signal includes dry contact, open collector, voltage, wide range voltage at maximum count speed upto 30Hz. The front panel protection is IP54 and wiring connection is easily done via the terminal block connector, making it secure and reliable. CE, UL and RoHS compliant.
-
product
Digital Clamp-on AMmeter / Multimeter
HH2099
3-1/2 digil Large LCD display 2000 count with symbolic signs. CAT II 600V rated. Basic accuracy 0.5%. Auto Ranging High Voltage test up to 600V DC and 600V AC. Higher Current test up to 1000A AC/DC. Measure Resistance up to 20MΩ
-
product
PXI 32-channel High Voltage Data Acquisition
M9216A
The M9216A is a high voltage data acquisition module that allows simultaneous measurement of eight channels of positive voltages ranging from 1 mV to 100 V. Each channel comes with a concurrent 5 V and 100 V measurement range, with every channel capable of acquiring very low and very high voltages without the need for switching ranges.
-
product
Linear Regulated Power Supplies (to 150 watts)
Gold Box "Infinity"
*Highly Configurable, with a seemingly Infinite number of Options*Any slot voltage from 1.5v to 150v is available*Remote Sensing*Open Sense protection*Isolated output*Short circuit and overload protection with enhanced surge capabilities*No minimum load required*Internal EMI Filtering*Pluggable connectors*Can be mounted on two surfaces in any orientation
-
product
PXI 2A Multiplexer, 1-Bank, 4-Channel, 32-Pole
40-614B-020
This 1-bank, 4-channel, 32-pole version is part of the 40-614B High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Power Supply
The Power Supply Systems are the heart of any experiment. They provide the High voltage and Low voltage required by the detectors and by the related front-end electronics. The quality of the power supply is critical to obtain the best performance from the set-up. The sensibility of modern detectors, in fact, make them susceptible to any even small variation in the power supply, and so features like low Noise, low Ripple and high stability become essential in the design of a performing power supply system. Strong of 40 years of collaboration with the most important research labs worldwide CAEN offers today sophisticated High Voltage Power Supply and Low Voltage Power Supply Systems. The demonstration of this successful long-standing tradition is the “CMS Crystal Award 2009” that CAEN received for the development and production of the power system for the CMS tracker. CAEN offers a wide selection of Power Supplies in different form factors and standards:- For smaller set-ups Standalone or modular (NIM / VME) products or are the ideal fit.- For bigger set-ups, where a high number of High voltages and Low voltages is required, the Mainframe Systems and Boards (up to 48 channels/board, up to 768 channels in a single Mainframe) are the most recommended.
-
product
Hipot Tests
The hipot test (high potential test) or dielectric withstand test, is used to determine the insulation and dielectric strength. It is carried out on modules, devices and systems of protection class I + II. In this test, the insulation of the test object is subjected to greater stress by the high voltage than in normal operation. It is determined whether the insulation of all current-carrying conductors, as well as the safety distance to the enclosure, is sufficient and complies with the legal requirements under normal operating conditions.We will be happy to assist you with any questions or solutions to problems.You will find a large selection of high-voltage testers in our comprehensive shop.Questions? We are always at your disposal.
-
product
NanoVIP® TWO™
NANOVIP® TWO™ is a modern, powerful, portable network analyzer developed for professional analysis of consumption and power quality of the most complex electrical networks.It can be used on single-phase, two-phase, three-phase (3 or 4 wires balanced) networks, low and medium voltage.
-
product
USB, AC 110 VOLT AND 12 VOLT SOCKET TESTER PACK
MDPPTST
*USB, 12V and AC 110V socket testers provide the user with a simple way to test electrical sockets on a vehicle*Socket testers illuminate when when the respected voltage is detected, indicating the health of the socket*USB socket tester illuminates when 4.4V - 5.25V is detected
-
product
9-Pin D-type Female, Solder Bucket, HV
92-960-009-F-HV
9-Pin Female D-type Connector, High Voltage, Solder Bucket - Without Backshell
-
product
IBM AT/ISA, Vectorbord Plugbord
4617-4
VECTOR Electronics and Technology, Inc.
98 contacts (49 each side) on 0.100" centers.Voltage/Ground Plane. Plane surfaces solder-coated for user convenience.To simulate plated-thru holes committed to voltage or groundplanes use Vector T123 eyelets. Vector T123 eyelets available separately (for use without pins). I/O mounting area for up to 70-pin D-sub and ribboncable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
product
PXI/PXIe High Density 2A Multiplexer, 4-Bank, 16-Channel, 2-Pole
42-614D-007
The 40-614D-007 (PXI) and 42-614D-007 (PXIe) 4-bank, 16-channel, 2-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Handheld PD Tester
Weshine Electric Manufacturing Co., Ltd
TEV partial discharge inspection instrument uses two emerging technologies, transient-to-ground voltage (TEV) measurement and ultrasonic (US) measurement, to detect faults in switchgear. The equipment is portable and easy to operate. The TEV sensor is attached to the wall of the box, and the US sensor scans and detects along the gap on the switch cabinet.
-
product
Phase Rotation Tester with Voltmeter
885 PR
Standard Electric Works Co., Ltd
● 3 functions in one unit: Phase Rotation, Phase Presence, Voltmeter● LCD contact type Phase Rotation Tester● Large LCD to show phase rotation and phase presence● Check a wide range of three phase power sources● Voltage range for phase rotation test: 75~600V AC ● Frequency range: 40~400Hz● 6000-count voltmeter● Auto ranging Voltmeter AC/DC● Data hold function● Auto power off● Convenient stand for viewing● Easy to use● Comply with EN 61010-1 CAT III 600V EN 61010-2-033 EN 61326-1
-
product
Portable Vibration Calibrator
AT-2040
With AT-2040 you will find the features required for your application without having to install cumbersome and expensive addons. AT-2040 features a full-automatic sensitivity test mode, sensor simulation, power supply output for sensors that require voltage such as the 7310 and 991V aviation sensors, a built-in sensor charge amplifier for both single-ended and differential charge accelerometers, and a custom sensor input that can be configured to fit most accelerometers with a one to one cable.
-
product
Panel Mounted Power Quality and Energy Monitor.
PM7503
The PM7503 Power Quality and Energy Monitor is a panel mounted variant of our top of the range PM7000 Power Quality Analyser. As with the PM7000 and P7000FLM, as well as recording all other important power quality parameters, the PM7503 with the optional Interharmonics upgrade is able to record 100 Voltage or Current harmonics on all 4 inputs at the same time.
-
product
Digital 12V Battery Tester
BT175
Schumacher Electric Corporation
DIGITAL TESTER FOR 12V BATTERIES/STARTER SYSTEMS/CHARGING SYSTEMSHand-held tester checks the battery, starting and charging systems with digital accuracyDigital display guides you through the testing process and shows voltage and CCALEDs indicate OK, OK & Recharge, Recharge & Retest, Weak, Bad Battery and Error For 12V SLI and VRLA/AGM/GEL batteriesAccepts rating types CCA, CA, EN, IEC, DIN and SAEOperating range: 100-1200 CCA (SAE)Testing voltage: 7-15VContents: (1) Schumacher BT175 Digital Battery Tester (1) owner's manual
-
product
Oscillators
VCXO
A crystal oscillator whose output frequency varies based on an applied control voltage.
-
product
VME Analog Output Module
DP-VME-2115
DP-VME-2115 is an industrial standard 24 channel D/A (Digital to Analog) board. It incorporates most of the features which are demanded in industrial applications. Each Digital to Analog Converter (DAC) is provided with a separate reference voltage selection either from internally generated reference or from the external input. This external input reference signal is passed into the protection circuits before it is fed to any active components. The input protection circuit is designed for ± 25Vp-p input ranges. The DAC output may be unipolar or bipolar and the output is jumper selectable, which is routed to the VME P2 connector, with short circuit protection of upto 30mA.
