Verifiers
-
Product
MPO Visual Cable Verifier Kit
KI-TK832
-
Kingfisher's unique and innovate MPO Visual Cable Verifier Kit is a quick, versatile and inexpensive way to visually check MPO cable installations and patch leads for polarity and continuity, and overall end face condition. Just connect the source, and view the far end with the microscope to observe the repeating color pattern at the far end.
-
Product
Logic Analyzer Probe
FS2520
-
The FS2520 is our newest and fastest logic analyzer probe used to test DDR4 DIMM memory. It is designed to work exclusively with 3 Keysight U4164A logic analysis modules operating in either Quad Sample State or Quarter Channel 10GHz timing modes. This gives the user an extremely effective tool for debugging, testing and verifying DDR4 DIMMs running above 4000MT/s. It’s like having a 100 channel scope.
-
Product
Radio Survey/Inspection
-
Radio survey is a set of testing services provided for a vessel to verify and confirm its readiness and safety for navigation in appropriate sea area. The condition of the ship and its equipment shall be maintained to conform with the provisions of the SOLAS regulations to ensure that the ship in all respects will remain fit to proceed to sea without danger to the ship or persons on board.
-
Product
PoE Voltage Monitor Detect & Verify
PE-400
-
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
Product
High Voltage Breakdown Test Sets
HT-Series
-
Dielectric Voltage Withstand Test or High Potential Test (HIPOT test) is a 100% production line test to verify the quality & electrical safety characteristics of products.
-
Product
Proving Unit& Calibrators
-
Shanghai Beha Electronics Co., Ltd.
Calibration box is used to verify and proof any High Voltage Insulation Testers. It can be utilized to calibrate all High Voltage Insulation Testers very accurately Analogs or Digitals.
-
Product
PCBA & Bare Board Cleanliness Tester
Zero-Ion G3
-
For two decades, thousands of electronics assemblers have relied on the Zero-Ion cleanliness testing to verify the cleanliness of post-reflow printed circuit assemblies and bare boards. Over time, as PCB assemblies have become more complex and more densely populated with surface mount components, and as vigorous quality standards such as ISO, TQM and Six Sigma have become commonplace, the ability to meet—and confirm—cleanliness levels has grown in importance. The Zero-Ion ROSE tester has kept pace with customer requirements, and the Zero-Ion G3 is the most advanced Zero-Ion ever designed, capable of testing assemblies reflowed with any solder paste, including no clean—yet its also one of the most affordable cleanliness testers on the market as well, with performance and ease of use second to none.
-
Product
High Accuracy In-Situ Mass Flow Verifier
HA-MFV
-
The HA-MFV, High Accuracy Mass Flow Verifier is designed for use on process tools to verify mass flow control flow rates in-situ. Available with EtherCAT® or DeviceNet™ communications and measurement accuracy of 1.0% of reading, the HA-MFV can verify MFC flow with the actual process gas significantly better than older rate-of-rise devices or process chamber rate-of rise methods.
-
Product
Ammeters
-
*Measures AC current from 1 to 2000 Amps on system voltages up to 500kV line-to-ground*Stores the last 4 readings*Dual measurement modes, peak hold and real time*Takes spot-load checks with ease*Verifies phases are balanced*Versatile for overhead and underground applications*Compact, lightweight design
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm
50-294-031
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Structural Testing
-
Structural testing is used to verify the static strength, or fatigue strength, of a component by applying measured loads. Testing can be done to failure, to contractual requirements, or to validate finite element model predictions.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm - SPST
50-294-131
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Vector Signal Generator
R&S®SMW200A
Vector Signal Generator
Performance and functionality requirements vary depending on test setup and application. The R&S®SMW200A is unrivaled in mastering this challenge and sets new standards for signal generators. When developing and verifying any type of DUT, including component, module and complete base stations – the R&S®SMW200A always easily generates the appropriate test signals with top performance. The flexible modular design of the R&S®SMW200A can be equipped with the exact options required for specific applications. Any configuration is possible, from a classic single-path vector signal generator to a multichannel MIMO receiver tester.
-
Product
Day Camera Testing
-
CI Systems' CCD test stations are used to carry out all the necessary tests to verify and compare the quality of a CCD based camera. These stations are based on CI Systems' reflective collimators, Visible Radiation Sources, special targets and integrated software, to project standard patterns with known geometry and intensity to the Unit Under Test. As a result, these stations are turnkey solutions for the CCD camera testing needs.
-
Product
Product Support Equipment
-
The TTU/515E or O/I Level Test Set was developed to provide a full end-to-end test of the NACES and FAST electronic sequencers used on the NACES ejection seat. The O/ITS provides simulated inputs and measures the timing of initiator firing sequencer outputs. The O/ITS, via a serial channel in the test connector, performs discrete element diagnostics on all the sequencer's redundant electronics and verifies its full functionality.
-
Product
Anite Conformance Toolset
-
Ensure mobile devices perform as expected on a live mobile network by verifying their compliance with latest industry specificationsUse independently validated test cases when performing GCF and PTCRB device certification testingAccess comprehensive test case portfolio covering all GSM-evolved technologies, from GSM through HSPA+ up to the very latest LTE-Advanced and IMS test cases
-
Product
Network Emulator
-
With Simnovus Network Emulator, it is easy to validate if your device works on networks across any region in the world under different network configurations. It supports carrier bandwidth up to 100MHz and frequency ranges from 70MHz to 6GHz for both FDD and TDD. And thanks to the software-based radio (SDR) design, you can also verify custom bands including CBRS.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm - SPST
40-294-133
Programmable Resistor Modules
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Professional Cable Tester/Tracer with Tone Generator
TC-NT2
-
The TC-NT2 is a convenient and comprehensive cable tester for network professionals. Its powerful and user-friendly features enable network installers to accurately check pin configurations of various voice and data communication cables. The TC-NT2 includes a master unit that transmits test signals to its corre-sponding remote terminator to verify cable reliability
-
Product
SpaceWire Physical Layer Tester
141
-
The SpaceWire Physical Layer Tester (SPLT) is a tool designed to test, validate and verify a SpaceWire system across all levels of the SpaceWire standard. Two SpaceWire ports employ a special LVDS interface which allows the transmitted signals to be deliberately and measurably manipulated to test the capability of a unit under test to receive signals of varying quality.
-
Product
Testing Technology
Testing of electrical machines
-
Specialized measuring instruments and procedures used to verify the electrical safety, protective measures, and operational reliability of industrial machinery and drives.
-
Product
Class 2 Sound Level Calibrator
SPC70
-
The SPC70 is a Class 2 sound level calibrator suitable for periodic testing of sound level meters and verifying their accuracy before and after readings, in accordance with international standards. The SPC70 is simple to use and provides a 1kHz reference at 94dB and 114dB. The output is accurate to 0.5dB with low levels of harmonic distortion. The SPC70 is compatible with the Martindale SP79 Class 2 Sound Level Meter and other meters with microphones up to 25mm.
-
Product
Calibration And Verification Instruments
-
The system of automatic calibration and verification consists of a computer of the operator's workplace and a control controller with a calibrator connected to it and a verified device. The device under test can have 4 to 16 working channels with a complicated circuit for connecting different types of signals: voltage, current, thermocouples, thermoresistance. The system allows a change in the set of operating ranges during calibration and calibration. The software development system used the LabVIEW development environment with the Real-Time module.
-
Product
AC Load Banks
K-1000 Series
-
Kongter Test & Measurement Co., Limited
Load bank testing is vital to replicate and verify the operation of critical backup power systems such as diesel generators and uninterruptible power supplies (UPS). Kongter offers a wide range of customer-tailored AC load banks that excel in a range of load test applications and environments.
-
Product
CTR Test Fixtures
-
Designed to hold electronic components or assemblies in place during testing, particularly for verifying the Current Transfer Ratio (CTR) of optocouplers.
-
Product
4.0mm Hazardous Live Parts Probe
CX-4.0
-
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts through top openings. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN61010-1, UL3101-1, and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is made of stainless steel.
-
Product
Wire Systems Analyzer
Console Test Systems (CTS)
-
Wire Systems Analyzer Commercial Roll around detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex. Used to verify the operation of relays, circuit breakers, indicators, switches, diodes, transformers, 1553 couplers, etc.
-
Product
PXI Resistor Module 2-Channel 1.5R to 4.09k with SPDT
40-293-123
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Portable Bar Code Verifier
Inspector Model D4000 Auto Optic
-
The Model D4000 Auto Optic provides ISO 15416 and ANSI X3.182 Method. This unique portable bar code verifier can interface with either the patented RJS Auto-Optic scan head or a laser scanner (either in a single piece or connected with a cable). Store and print capability, multiple scan averaging and subsymbology choices are easily accessed through a simple four-button user interface. The scanners are easily installed by the user, which makes the unit quickly adaptable to practically any verification requirement.
-
Product
Electrostatic Field Meter - Hand Held Field Meter for Locating and Measuring Electrostatic Field Density
PFM-711B
-
- Lightweight, portable, hand-held Field Meter- Measure in 1 volt/in increments 0 to ±1,999 Volts- Measure in 10 V/in increments 0 to ±20,000 VoltsAccuracy of <±5%- LED ranging lights help position the meter at the right distance- Zero button allows the display to be adjusted to zero (0)- Hold feature freezes the measurement on the display- Use with Prostat CPM-720B Charge Plate Monitor and PCS-730B Electrostatic Charger- Use with Prostat PGA-710B AutoAnalysis System or X-Y Plotter- Analyze Footwear/Flooring Combinations- Verify Ionizer Balance and Decay Time Performance- 2-year Limited Warranty (1 year on the sensor)
