- Pickering Interfaces Inc.
product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
Spectrum Analysis For E5081A Up To 20 GHz
S960904B
The Keysight S960904 spectrum analyzer (SA) software application adds high-performance spectrum analysis to the E5081A ENA-X up to 20 GHz. With fast-stepped FFT sweeps resulting from optimized data processing, the SA software application provides quick spurious searches over broad frequency ranges. The application enables simultaneous spectrum measurements using test and reference receivers. The multichannel SA pairs with the internal swept-signal generators for efficient measurements of spuriou...show more -
product
Dual Channel 14-bit 3.0 GSPS Analog to Digital Converter
ADC32RF45
The ADC32RF45 is a 14-bit, 3.0-GSPS, dual-channel, analog-to-digital converter (ADC) that supports RF sampling with input frequencies up to 4 GHz and beyond. Designed for high signal-to-noise ratio (SNR), the ADC32RF45 delivers a noise spectral density of –155 dBFS/Hz as well as excellent dynamic range and channel isolation over a large input frequency range. The buffered analog input with on-chip termination provides uniform input impedance across a wide frequency range and minimizes sample-and-hold glitch energy.
-
product
CompactPCI
CPCI-ADDA
The CPCI-ADDA module offers a complete solution forhigh performance data acquisition applications. Boththe ADC’s and the DAC’s use 10 mS converters thatwill support up to 100khz signals. The CPCI-ADDAsupports P.I.D. loop closure frame rates of up to 4 KHzper channel. The CPCI host can download gain andsetpoint changes on the fly. The CPCI host can readback the current values for feedback, error, setpointand output drive on each channel. The local DSPprocessor can be used for data processing such asdigital filters and FFT’s. The DSP can also be used asa waveform generator to drive the 16 bit DAC.
-
product
RS-232 to RS-422/RS-485 Optically Isolated Interface Converter
Model 245
Total Isolation; Selectable RS-422 or RS-485; Selectable 2 or 4 wire RS-485; Intelligent Control of RS-485; TD & RD LED's on Each Side of Opto Barrier; Data Rates up to 128 KBPS. The Model 245 RS-232 to RS-422/RS-485 Optically Isolated Interface Converter is an optically isolated version of the Model 285.
-
product
Portable Density/Specific Gravity Meter
DA-130N
Measuring method Natural Oscillation typeMeasurement object Liquid sample test materialsRange 0.0000 ~ 2.0000 g/cm3Precision 0.001 g/cm3Resolution 0.0001 g/cm3Temperature range 0 ~ 40.0CTemperature compensation Up to 10 entries for temperature compensation coefficient and converted temperatureAutomatic calibration All density values of pure water needed for auto calibration can be stored.Number of data 1,100 samplesExternal outputPC or Printer can be connected. (not both) IrDA interface is standard equipped. Connection via RS-232C requires optional infrared RS converter (98-029-0007).
-
product
Single Or Dual Stream MIL-STD-1553 A/B &4, 8 Or 12 Channel ARINC429 Mixed ProtocolTest & Simulation Module For Standard Ethernet
ANET-MxAy
Single or dual stream MIL-STD-1553 A/B and 4, 8 or 12 channel ARINC429 mixed protocol Test & Simulation module for standard Ethernet. The ANET embedded Linux operating system gives the unique capability to run the optional PBA.pro Engine right in the box.Another option is the ANET-ADK onboard software development kit where users create runtime applications (e.g. MIL-STD-1553 to Ethernet Converter / ARINC429 to Ethernet Converter , MIL-STD-1553 to Ethernet Gateway / ARINC429 to Ethernet Gatew...show more -
product
In-Circuit Emulator - 80C186/80C188 Family
DS-186
* Support for 80C186/8/XL/EA/EB/EC, 8086/8, V20/25/30/40/50 and other Microprocessors * Full-speed Emulation up to 25MHz * 1MB of Zero-Wait-State Mapped Memory * 8K x 32-bit Frames Dynamic Trace Buffer * 1MB Hardware Breakpoints * 115 KBaud RS-232 Communication Link * Numeric Coprocessor Support * OMF Converter * Support for Borland, Microsoft and Intel Compilers * Full Support for C, C++, Pascal and Assembler
-
product
16 Channel, 12-Bit Analog Input PCI Card
PCI-AI12-16A
Model PCI-AI12-16 is a multifunction, high-speed, analog-to-digital converter board for use in PCI-Bus computers. It accepts up to 16 single-ended or eight differential inputs. The board uses a low-noise, multilayer printed circuit board. Inputs are protected against overvoltage conditions up to ±35 volts and typically survive static discharges beyond 4000 volts.
-
product
Generic RF ATE Test
The Generic RF ATE is developed to test the Radar and Radar Subsystems. The ATE is primarily built using an instrumentation control, precision RF routing systems and rack mounted test instruments. Generic RF ATE system enables measurement of parameters of Radar equipment such as Local Oscillators, Waveform Generators, Up and Down Converters, Analog Receivers, Array Group Receiver Units, TR Modules. The ATE is configured to test the Radars upto 18GHz frequency range.
-
product
Sophisticated Audio and Video Test Patterns
VQL
VQL Instantly reveals your video display, codec, scaler, converter or other video device performance VQL test patterns cover all 3 levels of video QA/QC: Instant visual-aural Quality Estimation Objective Measurements of video and audio performance Fully automated (unattended) Quality Control VQL features: Compatibility with all commonly used software or hardware codecs and media players VideoQ VQV / VQMA / VQTS / VQDM compatible tests Wide range of video frame sizes: from 192x108 to 4096x3072...show more -
product
8-Channel VME LVDT/RVDT Scanner
V550
The V550 is a 6U, one-slot VME module which will acquire position data from up to eight LVDT (linear variable differential transformer) position sensors. The LVDT sensors are excited by an ultrastable synthesized sinewave generator, and conditioned by a precision 16-bit A/D converter followed by digital signal processing. The resident microprocessor supervises scanning and signal conditioning, and places updated position data in VME-accessible dual-ported data registers for instant access from the VME bus.
-
product
In-line ICP® Charge Converters
In-line ICP® charge converters play a vital role in converting high impedance charge mode piezoelectric sensor signals into low impedance voltage signals, facilitating input to readout, recording, and analysis instruments. Specifically engineered for compatibility with high temperature piezoelectric sensors, these units are capable of operation in environments reaching up to 500°F (260°C). The series boasts ±2.5V or ±5.0 V output, offering a range of gain options, all packaged within a compact and durable casing. As a cost-effective alternative to laboratory charge amplifiers, in-line ICP® charge converters present an appealing choice for multi-channel applications.
-
product
RS-232 to RS-422/RS-485 Interface Converter
Model 365
FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; DataSpy® LCD Display; Intelligent Control of RS-485 Transmitter and Receiver; DTE/DCE Compatible; Data Rates Up to 115.2 KBPS. The Model 365 multimode interface converter allows operation in compliance with RS-485 or RS-422 equipment, and RS-232.
-
product
Frequency Up Converters
Are integrated assemblies that convert low frequency RF signals to higher frequency RF signals.
-
product
PCI Data Acquisition Boards
AD8CH12B-100DMA Series - Single low-spur 8-bit, 100 MS/s
Model AD8CH12-100DMA has eight simultaneous-sampling 12-bit A/D converters, and can continuously acquire and transfer hundreds of megabytes or even gigabytes of A/D data directly into host system memory at up to 100 MB/s, via 64 or 32 bit PCIbus DMA. It can acquire and transfer eight 8-bit A/D channels at up to 12.5 MSPS each (100MB/sec aggregate), or eight 12-bit A/D channels at up to 6.25 MSPS each, or four 8-bit channels at up to 25 MSPS each, or four 12-bit channels at up to 12.5 MSPS each.
-
product
Dynamic Signal Analyser
Dynamic signal analyzers provide highly accurate measurement and analysis, and are widely used in audio testing, acoustic measurement, environmental noise testing, vibration analysis, NVH measurement, machine condition monitoring, and rotating machinery evaluation. ADLINK's dynamic signal analyzer series features 24-bit analog-to-digital converters (ADCs) with sampling rates up to 432 kS/s for PXI, PCI, and USB platforms for flexible yet accurate measurement supporting high performance and cost-effectiveness in a wide variety of testing applications.
-
product
Radar solution for level of casting molds & ladle cars
Our radar sensors measure the level of up to 1600 degrees Celsius hot aluminum or steel melts in ladle cars and casting molds with a measurement accuracy in the sub-millimeter range and a high measuring rate. This ensures a reliable, fast processing in the converter or foundry.
-
product
DC-DC Boost Converters
The ams step-up (boost) converter portfolio offers very high efficiencies of up to 96%, and the devices draw a very low quiescent current. High switching speeds enable the use of very small external inductors. These DC-DC boost converters can boost the input from a single battery cell to an output of up to 42V.
-
product
Multifrequency Clock Synthesizer - PCIe
Model 7890
Simultaneous synthesis of up to five different clocks, Eight SMC clock outputs, Ideal for A/D and D/A converter clock sources, Typical phase noise: -125 dBc/Hz @ 1 kHz offset
-
product
Multifrequency Clock Synthesizer - PMC
Model 7190
- Simultaneous synthesis of up to 5 different clocks- 8 SMC clock outputs- Ideal for A/D and D/A converter clock sources- Typical phase noise: -125 dBc/Hz @ 1 kHz offset- All clocks are phase-locked to input reference signal- Input reference frequency of 5 or 10 MHz- Four quad VCXOs allow selection from 16 different base frequencies- Output clocks of 1, 2, 4, 8, or 16 submultiples of VCXO base frequencies- Output clock frequencies between 50 and 500 MHz- Control and status via PCI bus interface
-
product
Miniature
Columbia Research Laboratories
This group is made up of the 6000 and 7000 Series Accelerometers. The 6000 Series offers detachable cables and connector assemblies, a special inverted seismic element for mechanical isolation and other features normally available only on standard size sensors. The 7000 Series are true "shear-mode" design accelerometers which offer performance characteristics and accuracies normally only available with standard size accelerometers. High temperature models of these series are available and will operate to +500°F. For best performance use with Columbia Model 4601 Charge Amplifier or Model 5810 Inline Charge Converter.
-
product
Wideband Digital Down Converter
A Digital Down Converter performs channel access functions in digital receivers. It is used for extracting a channel (frequency band) of interest in a wideband signal. Abaco Systems' wideband DDC core employs a quad DDC architecture to achieve ultra high performances. The core accepts up to 16-bit complex data and can process 1GSPS continuously. With a fully programmable architecture at all stages of the processing, this core combines flexibility and speed and can be used in combination with our dual-channel 1GSPS ADC module.
-
product
Spectrum Analysis For E5081A Up To 44 GHz
S960907B
The Keysight S960907B spectrum analyzer (SA) software application adds high-performance microwave spectrum analysis capabilities to the Keysight ENA-X up to 44 GHz. With fast stepped-FFT sweeps resulting from optimized data processing, the SA application provides quick spurious searches over broad frequency ranges. Conduct simultaneous spectrum measurements using test and reference receivers. For efficient measurements of spurious signals emanating from mixers and frequency converters, combine t...show more -
product
Software
TestPoint-based software for control, measurement and evaluation of electrochemical measurements, requires MS WindowsTM supports or interfaces,. CPC manages potentiostat control, data recording and data evaluation.Features: Up to 6 measurements channels, fast data access up to 300,000 data points per second. The evaluation allows differentiation, Tafel slope evaluation and other helpful routinesCPC runs with many multi-function AD/DA converter boards. It requires MS Windows (TM)
-
product
Interface Board, 8:1 USB
40-965-903
Converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 8 USB type A and 1 USB type B connectors. Allows the multiplexing of up to 8 USB1 or USB2 signals.
-
product
Network Management
PLANET Universal Network Management System is designed to monitor all kinds of deployed network devices, such as managed switches, media converters, routers, smart APs, VoIP phones, IP cameras, etc., compliant with the SNMP Protocol, ONVIF Protocol and PLANET Smart Discovery utility. It thus enables the administrator to centrally manage a network of up to 1024 nodes from a central office, greatly boosting network and power management efficiency. The NMS solution includes the software, hardware and Touch LCD controller series to attend to different applications. They all feature dashboard, topology and map viewing to make network management efficient and effective.
-
product
Up Converters
Macom Technology Solutions Holdings Inc.
MACOM's upconverters are widely used in point-to-point radio, broadband communications, and RADAR applications. Operating up to a frequency of 86 GHz, our upconverters feature an integrated image reject (balanced) mixer, LO buffer, and RF buffer. Some products also include LO multiplication and variable gain, all within a single chip. Available in die, or SMT lead-free QFN and LGA packages, our upconverters boast excellent performance with adjustable bias, high linearity and image rejection with low LO leakage
-
product
UV Fluorescence Total Reduced Sulfur Analyzer
Model T102
The Model T102 TRS analyzer uses the proven UV fluorescence principle to measure Total Reduced Sulfur at levels commonly required for ambient air monitoring.The Model T102 uses a high temperature external converter set at 850°C to allow conversion of H2S, methyl mercaptan, dimethyldisulfide, and methyl-disulfide to SO2 at this temperature with efficiency greater than 98%. A switching option alternately measures TRS and SO2 while showing both readings concurrently on the front display.All T Seri...show more -
product
2-CH 14-Bit 200 MS/s High-Speed PXI Express Digitizer
PXIe-9852
The ADLINK PXIe-9852 is a 2-CH 14-bit 200 MS/s digitizer for high frequency and wide dynamic range signals with an input frequency up to 90 MHz. The 90 MHz bandwidth analog input with 50Ω impedance is designed to receive ±0.2 V, ±2 V, or ±10 V high speed signals. With a PCI Express bus interface and ample onboard acquisition memory up to 1 GB, the PXIe-9852 easily manages simultaneous 2-CH data streaming. With high speed and high linearity 14-bit A/D converters and high stable onboard reference,...show more -
product
SparkFun BabyBuck Regulator Breakout
3.3V (AP63203)
Who doesn't occasionally need power regulation? We certainly do, so we've designed the SparkFun BabyBuck Regulator Breakout to help us with just such a task. Featuring the AP63203 from Diodes Inc, this breakout board takes advantage of a 2A synchronous buck converter that has a wide input voltage range of 3.8V to 32V and fully integrated 125mΩ high-side power MOSFET/68mΩ lowside power MOSFET to provide high-efficiency step-down DC/DC conversion. All of this snuggled up in a low-profile, TSOT26 package that's integrated into a 0.4in by 0.5in board.
