Up Converters
Increase the frequency of a signal.
-
Product
Isolated USB To RS-232/422/485 Converter
ADAM-4561
Digital / Analog Converter
Power from the USB portHot swap function supportedIsolation protection 3000 VDC providedAutomatic RS-485 data flow controlTransmission speed up to 115.2 kbps
-
Product
Modulation Distortion Up To 50 GHz
S930705B
-
S930705B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 50 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930704B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Standard High Speed A/D Converters
-
Analog Devices high speed A/D converters (ADCs) offer the best performance and highest sampling speed in the market. The product offerings include low IF A/D converters (20 MSPS to 125 MSPS), high IF a/d converters (125 MSPS to 1.3 GSPS), and wideband ADCs (>1 GSPS). The high speed a/d converter portfolio offers cost and performance optimized solutions for various applications such as communications infrastructure, electronic test and measurement, and aerospace and defense.
-
Product
Modulation Distortion Up To 125 GHz
S930712B
-
S930712B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 125 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S93072B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
Product
Binary to BCD Converter
BAC300
-
Computer Conversions Corporation
The BAC series of Binary to BCD converters will convert binary angle data to 5 digit BCD data scaled in degrees and decimal fractions of degrees. Units with display and/or data outputs are available. Custom scaling of the output to represent actual physical units of measure can be provided easily (i.e.: feet, lbs., meters, mills, etc.) They will also accept encoder outputs and display them at extremely low cost when compared to previous solutions.
-
Product
Isolated RS-232 To RS-422/485 Converter
ADAM-4520
-
Automatic RS-485 data flow control3000 VDC isolation protectionSurge protection RS-485 data lineTransmission speed up to 115.2 KbpsLED indicator to monitor status
-
Product
Single-Supply Voltage Output D/A Converters
-
Analog Devices offers the broadest portfolio of low voltage single-supply D/A converters (DACs) in the industry, which includes many leading products in performance and package size. A wide variety of applications use ADI precision nanoDAC® products because of their small footprint and robust range of features, including 8- to 16-bit resolution, low power, a fast 50 MHz SPI or 3.4 MHz I2C interface, and more, in a tiny package option. ADI’s nanoDAC+™ products offer enhanced features such as higher accuracy, improved dc performance, increased robustness, and lower glitch energy, among other advantages.
-
Product
Signal Converters & Load Cell Signal Converter
-
Mantracourt provide a range of signal converter modules which take load cell or strain bridge inputs and provide a data output in a variety of bus and protocol formats. Hardware formats include RS232, RS422 RS485, CAN and USB. Signal converter protocols include Industry Standards such as MODBUS, or Mantracourt’s own proprietary protocols which have been optimised for either ease of use (MantraASCII2) or higher speed communications (MantraBus2).
-
Product
Adapters & Converters
-
Using our prebuilt, off-the-shelf standard adapters, custom converters, or custom adapters, incorporate performance and process data from across your enterprise, without having to disrupt your manufacturing line or change the outputs or your manufacturing process.
-
Product
Single-Mode Fiber Optic To RS-232/422/485 Converter
ADAM-4542+
Serial-to-Fiber Optic Converter
1 x SC fiber connectorOperation mode: Point-to-Point,Redundant and Ring(half-duplex)Half/Full-duplex, bidirectional transmission modeAutomatic RS-485 data flow controlLED indicator to monitor status
-
Product
Straight Waveguide Sections up to 110 GHz
-
Fairview Microwave’s straight waveguide sections consists of 61 models that are available in sizes ranging from WR-10 to WR-137. These waveguide straights deliver VSWR as low as 1.03:1 and are available in section lengths from 3 inches to 12 inches. They are made of either painted copper alloy or gold-plated, oxygen-free hard copper (OFHC) and feature UG, CPR and UBR-style flanges. These waveguide straight sections are ideally suited for use in industrial, defense, aerospace, test and instrumentation, medical and telecom industries.
-
Product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
-
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
Product
Media Converter, 1000Mbps, SFP
EKI-2741F
-
Provides 1 x 1000 Mbps Ethernet port with RJ45 connectorProvides 1 x 1000 Mbps fiber port with SC or SFP (mini-GBIC) type connector for 1000Base-SX/LX deviceProvides DIP switch for full/half duplex settingSupports MDI/MDI-X auto crossoverSupports Auto-NegotiationSupports redundant 12 ~ 48 VDC power inputProvides flexible mounting: DIN-rail and Wall mountProvides Link Fault Pass-through (LFP)Jumbo Frame: 9K bytes
-
Product
Unmanaged Media Converters
IMC-370 Series
-
Industrial Gigabit Ethernet-to-fiber media converters.
-
Product
Adapters & Pin Converters
-
Need to adapt your emulator's JTAG connection? We have a variety of pin converters to help connect your debug probe to your target board's JTAG connection, such as TI, MIPI, ARM, and Cortex.
-
Product
DC to LVDT and DC to RVDT Converters
-
Computer Conversions Corporation
The SLVT Series are complete, low profile, continuously updating, single channel, Isolated Digital to LVDT Converters used to simulate the output of LVDT's (Linear velocity displacement transducers), RVDT's (Rotary...) and other phase/voltage sensitive AC devices. They provide a very precise linear AC voltage output proportionate to the magnitude of the input data, in or out of phase respective of the AC reference input as determined by the MSB of the input word (offset binary format).
-
Product
mAEStro Audio Digital to Analog Converter
-
The mAEStro ADAC-100 receives AES/EBU (AES3) or S/PDIF digital audio and converts it to two channels of analog audio. It automatically detects sample rates up to 96kHz with low-jitter clock recovery. Two balanced line-level audio outputs are provided on XLR connectors on the rear panel. For convenient monitoring, a stereo headphone mini-jack and volume control are provided on the front panel.
-
Product
Frequency Converter Upwards
UPCONVERTER 10 GHz LXI
-
UPCONVERTER 10 GHz осуществляет программно управляемый перенос вверх спектра шириной 150 МГц, поступающего на вход сигнала, в любую точку спектрального диапазона от 10 МГц до 10 ГГц. Перенос спектра осуществляется по супергетеродинному принципу с тремя ступенями переноса. Благодаря этому во всем рабочем диапазоне спектра достигаются высокие уровни подавления несущей частоты и зеркального канала. Также UPCONVERTER 10 GHz обладает уникальной возможностью, не имеющей аналогов среди приборов подобного типа – задавать значение промежуточной частоты (входного сигнала) для переноса в диапазоне от 50 до 400 МГц. Помимо этого, прибор позволяет передавать входной сигнал частотой от 0,1 до 400 МГц напрямую на выход, без переноса. Благодаря этому, совместно с UPCONVERTER 10 GHz в качестве генератора промежуточной частоты может быть использован широкий спектр генераторов зарубежного и отечественного производства. Холдинг «Информтест» предлагает потребителям генераторы собственной разработки MGKS and MGVCh , as well as the first Russian MT transceiver module , which are fully compatible with the input characteristics of UPCONVERTER 10 GHz. Together with generators produced by the holding "Informtest" UPCONVERTER 10 GHz under the control of a common software shell makes up a synthetic instrument - a ready-made solution for testing microwave devices and radio reception channels.
-
Product
START-1000 Start/run Up Time Test System
-
Hangzhou Everfine Photo-E-Info Co., LTD
Start-1000 can be used to record the start rise time and waveform of the light source in real time, and according to the design requirements of the EU directive 1194/2012, Energy Star and the international standard IEC60969, etc., it is specially used for LED lights, lamps and energy-saving lamps. And it can also be used to measure the photometry parameters of stable light sources.
-
Product
O/E Converter
TIA-950
-
The TIA-950 optical receiver is the optimum instrument for the laboratory or for field use. This optical receiver can be used with a wide range of oscilloscopes and digitisers to provide the utility of a convenient, easy to use fibre optic probe. This compact unit mounts directly on the BNC input of an oscilloscope.
-
Product
Modulation Distortion For E5081A Up To 20 GHz
S960704B
-
The Keysight S960704B modulation distortion software application enables fast and accurate active device modulation distortion characterization under modulated signal conditions up to 20 GHz. The wide dynamic range and vector error correction of the ENA-X yield an extremely low residual EVM of the test setup, delivering a complete picture of your device’s signal distortion performance without test system interference. S960704B software measures EVM, NPR, ACPR, and decomposes linear and nonlinear signals by spectrally correlating input and output spectrum without needing to demodulate. Integration with the ENA-X measurement flexibility enables quick modulated signal distortion measurements along with traditional VNA tests.
-
Product
Voltage to Frequency Converters
-
Analog Devices has the widest range of voltage-to-frequency converters (VFCs) for the instrumentation, industrial, and automation markets. They are ideally suited for use in analog-to-digital conversion, long-term integration, linear frequency modulation and demodulation, and frequency-to-voltage conversion. ADI’s latest family of VFCs, the AD774x series, is based on Σ-Δ technology and provides high linearity in tiny packages at low cost.
-
Product
Fuel Flow and Torque Converter
Model 44SM1
-
This self-contained, remotely mountable Second Harmonic Fuel Flow Interface accepts data from a second harmonic fuel flow transmitter then converts this information into a frequency output proportional to fuel flow. In addition, this module will accept signals from a T56 Torque Tranducer and provide a DC voltage proportional to Torque. Typical application is for use with Flight Management and Nav Management Systems. The use of field proven designs and carefully selected components assures high reliability field performance.
-
Product
Serial Data Converters
CONV232/485 and CONV232/422
-
CONV232/485 and CONV232/422 convert between RS-232 communications (as used by the COM1 and COM2 ports standard on most motherboards) and balanced-mode, long distance RS-485 and RS-422 communications. CONV232/485 was designed for use with our REMOTE ACCES line when there is no RS-485 port on your PC, but may also be used in other, similar applications.
-
Product
IRIG B to NTP/SNTP Converter
-
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
Product
Video Scalers, Switchers & Format Converters
-
Enjoy painless signal management whatever your source or display. Digital, broadcast or analog: we’ve got it covered with our wide range of solutions. For the ultimate experience, go above and beyond with switcher/scalers that not only include scaling and format conversion, but also add advanced features including multi-window video, audio management, keying, still stores and logo layers.
-
Product
IPv6 to IPv4 Converter
-
An IPv6 to IPv4 Gateway is known by many names, including IPv4 IPv6 converter, IPv6 to IPv4 gateway, IPv6 to IPv4 network gateway, IPv6 converter, IPv6 gateway, or IPv4 converter. Some people refer to these solutions as IPv6 Compatibility tool, IPv6 compatibility appliance, IPv6 compatibility device, IPv6 transition mechanism or IPv4 to IPv6 tool.
-
Product
Telemetry Transmitter for FM with up to 3 Bands
LS-11-F
-
The LS-11-F portable FM test transmitter is designed for checkout and troubleshooting of telemetry receiving systems operating with FM modulation. For applications with any of the ARTM modulations (Tier 0, Tier I, or Tier II), please refer to the LS-11-M Data Sheet. Complete ground stations including the antenna with LNA, RF down-converter, IF receiver, bit synchronizer, and PCM decommutator can be tested and bit error tests performed. The design allows secure links to be tested with an external encryptor. The Test Transmitter contains an internal PCM Data Simulator and Pseudorandom patterngenerator that operates in a BERT mode. The device provides simulated clock and data (without transmitter enabled) and accepts external data for modulating the internal transmitter. Complete setup can be achieved locally through the keypad and two-line LCD display or remotely through the USB Interface. Operational parameters include the PCM format parameter database information (frame sync patterns, wavewords, etc…), pre-modulation filter selection, transmitter carrier frequency, transmitter deviation, and output power level. Output power can be selected from approx. -60 to +5 dBm in 5 dB steps. The Test Transmitter contains a LiFePO4 Battery (Lithium Iron Phosphate), which provides higher energy density at ¼ the weight of legacy lead-acid batteries. The unit also provides an internal battery charger and will operate for up to twelve hours on battery power having received on a full charge.
-
Product
Frequency Converters
-
Analytic Systems' Single and 3-Phase Sine-Wave Converters deliver output power ranging from 250 VA to 5000 VA. Our Frequency Converters also generate nominal output voltages of 115 VAC or 220 VAC, at frequencies of 50, 60 or 400 Hz. A broad range of input voltages are available.
-
Product
LVDT to Digital-RVDT to Digital Converters
ITA
Computer Conversions Corporation
LVDT Displacement transducers accurately measure position and displacement. The strength of the LVDT is in its principle of operation. As LVDT sensors are inductive, there is no electrical connection across the sensor, which ensures clean, accurate data and a long life.
