Showing results: 106 - 120 of 818 items found.
-
RI 700 -
Ranatec Instrument AB
RI 700 Carrier-to-Noise Generator, 0.5-2.7 GHz, 8 channels, is a wideband Carrier-to-Noise Generator with high dynamic range and web browser user interface.
-
Model T265 -
Teledyne Advanced Pollution Instrumentation
The Model T265 is the only commercially available US EPA Federal Reference Method for Ambient Ozone Monitoring according to the latest US EPA regulatory rules for O3. The instrument uses Chemilumescence with Nitric Oxide (NO) as a reagent, making is safe, stable, and effective for all applications. The NO-CL method for Ozone has several advantages over the conventional UV absorption technology, including the avoidance of positive and commonly found interferrents such as VOCs, fine particulates, Mercury, turpines, ClO2, and others. If these pollutants are present in the atmosphere, it can cause UV absorption analyzers to give an artificially high Ozone measurement. The innovative T265 combines speed of response, sensitivity and stability of our proven nitrogen oxide analyzer, with a simple user interface, to provide reliable ozone measurements under the harshest conditions.
-
TA102A -
MSA
The TA102A is a single-channel Combustible Gas Trip Amplifier Module designed for use with one General Monitors intelligent transmitter to monitor combustible gases and vapors within the lower explosive limit (LEL) and provide status indication and alarm outputs. Microprocessor-based electronics allow all options to be user selectable through a front panel interface (mode / select switch and digital display).
-
CF extend 180CIB -
Sycard Technology
For those applications that require access to a CompactFlash™ card that can't use a standard extender card, Sycard provides the CF extend 180CIB (Card Interface Board) which allows full access to all 50-signal and power pins on the CompactFlash™ peripheral. Standard 0.1" headers allow the user to connect standard 26-pin ribbon cables to test or prototype hardware.
-
CF extend 180HIB -
Sycard Technology
For those applications that require access to the CompactFlash™ interface that can't use a standard extender card, Sycard provides the CF extend 180 HIB (Host Interface Board). The CF extend 180HIB allows full access to all 50-signal and power pins on the CompactFlash™ host. Standard 0.1" headers allow the user to connect standard 26-pin ribbon cables to test or prototype hardware.
-
Vapor Pro® XL -
Ametek Brookfield
Improved repeatability, precision, flexibility and an advanced user interface – the Vapor Pro® XL is the latest in moisture specific analysis technology from Computrac®. The VPXL is ideal for nearly any application in which Karl Fischer titration is used.
-
Probat Burns
Produce a consistently high-quality product with a control system that’s easy to integrate into any process, simple or complex. Probat control systems feature clearly designed user interfaces and the ability to store and export production data as needed. Available as both semi- and fully automatic systems, our control systems enhance the performance of our commercial coffee roasters and grinders to yield superior results.
-
LAB SMP -
ET System Electronic GmbH
*Easiest operation via the front panel*Indication via graphic display*Constant current, voltage, resistance, power operation and simulation of PV characteristics*Creation of any voltage and current curves via memory card or digital interface (sequential control)*Voltage and current rise time (U and I slope) adjustable*Umax and Imax can be set by the user in order to limit the output voltage or current
-
Si8000m -
Polar Instruments Inc
TheSi8000m is an all new boundary element method field solver , which builds on the familiar easy to use user interface in earlier Polar impedance design systems. The Si8000m adds enhanced modeling to predict the finished impedance of multiple dielectric PCB builds and also takes into account the local variations in dielectric constant on close spaced differential structures.
-
Corr Instruments, llc
CorrVisual software provides an easy to use and flexible graphical user interface for the setup, control, and data visualization of Corr Instruments'' nanoCorr Coupled Multielectrode Array Sensor (CMAS) Analyzers.
-
NI
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
KINGSINE Electric Automation Co., Ltd.
1, Consisting of Function modularization design and plug-in frame, each module contains self-calibration function, plug and play when change module, easy to maintain for customer.2, Adopt TFT LCD display screen with clear and beautiful software interface design, user can operate easily3, AC/DC current input for wide range only, satisfy all power supply standard requested.
-
Magnifi® -
Eddyfi NDT Inc.
Eddyfi® Magnifi® is a constantly evolving, integrated electromagnetic inspection data acquisition and analysis software. It boasts an intuitive graphical user interface (GUI) suited to modern devices, powerful reporting functions and data management, as well as simple inspection configurations.
-
DPlus -
Salland Engineering
Our new data analysis software DPlus has been built for (product) engineers with the latest and newest software technologies. It features a modern and intuitive, context-driven user interface and the predefined building blocks help you quickly understand complex data analysis.
-
Magpie 2 -
LXinstruments GmbH
LXinstruments Magpie 2 is a further developed evaluation and data mining application for our test database. The data to be evaluated can be preselected using complex, easily configurable filters. Based on the selected data, reports and trend analyzes can then be created and statistical studies, machine and process capability analyzes carried out. Administration of the database is also easily possible for appropriately authorized users via a graphical user interface.