-
Product
Condition Monitoring
-
Condition Monitoring by TP - generator, turbine, and transformer condition monitoring
-
Product
60kw off grid power inverter 110/220V split-phase output converter
SDP-60KW
-
Zhejiang Sandi Electric Co., Ltd
Our SDP series Off Grid Pure sine wave inverter is one of the most advanced DC to AC conversion products in the world, it is suitable use for areas without electricity, vehicles, ships, solar energy, wind turbine and other renewable energy systems and etc, can supply power and provide guarantee effectively for the areas with traffic inconveniences, in the mountains, pastoral, border, island and other areas without electricity.
-
Product
Aeroderivative & Heavy-Duty Gas Turbines
-
GE’s heavy-duty and aeroderivative gas turbines are efficient, versatile and reliable with individual output ranging from 34 MW to 544 MW. They are proven performers in simple and combined-cycle operation for pure power generation, cogeneration, mechanical drive, and waste-to-power.
-
Product
Dual Mode Wind Turbine Performance Lidar
ZephIR DM
-
ZephIR DM is a Dual Mode variation of the successful 300 system. ZephIR DM measures wind characteristics in front of or behind a turbine from just 10 metres (33 feet) out to 300 metres (984 feet) situated inside the spinner or on top of the nacelle, during the operation of wind farms onshore and offshore (this is limited to 200m (656 feet) when in ground based vertical mode).
-
Product
Turbine Flow Meters
CT300, CT400
-
Flows up to 400 lpm (100 US gpm)Pressure up to 420 bar (6000 psi)Choice of 4-20mA and 0-5V outputs2-3 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-estersBi-directional
-
Product
Turbine Flow Meters
-
Axial turbine flow meters are designed with wear resistant internal components to provide trouble-free operation and a long service life. Fluid entering the flow meter is first conditioned by the inlet flow straightener which reduces turbulence in the fluid. The moving fluid causes the rotor to spin at a speed that is proportional to its flow rate. As the turbine blades on the rotor pass through the magnetic field of the pickup, an electronic pulse is generated.
-
Product
Wind Sensor
FT722
-
Specifically designed for wind turbine control, the FT722 reads wind speeds from 0-50m/s. Its inovative design incorperates a series of "turbulators" (patient pending) which condition the air flow. With updated software, and calibration in our new state-of-the-art wind tunnel, the FT722 delivers our highest levels of accuracy in wind speed, wind direction and accoustic temperature measurement.
-
Product
Exhaust Gas Thermocouples
HYBRID Series
-
The AMETEK Hybrid Series Exhaust Gas Thermocouples for Frame 7 and 9 applications have been designed, fully tested and qualified to meet OEM specifications. AMETEK has worked closely with the OEM turbine manufacturer to qualify and engine test this thermocouple as a direct replacement, or for upgrading an older style Exhaust Gas Thermocouple.
-
Product
Turbine Flow Meters
CT600
-
Flows up to 600 lpm (160 US gpm)Pressure up to 420 bar (6000 psi)Choice of 4-20mA and 0-5V outputs2-3 top ports as std for temperature / pressureBSP or SAE inlet / output portsFor use with oils, fuels, phosphate-estersBi-directional
-
Product
Inspection & Alignment Services
-
As a leading provider of precision measurement services for power generation and turbo-machinery, API has the professional experience necessary to minimize the overall downtime of the outage or rebuild schedule. The ability to fully utilize API’s precision measurement capabilities, combined with experienced Service Engineers in the turbine alignment process, differentiates API for complex alignments.
-
Product
Electrostatic Capacitance-Type Gap Detectors
VE series
-
VE series are non-contact type of vibration/small displacement detector with high accuracy which can measure the distance between conductor such as metal and sensor’s surface in micron/submicron resolution. It demonstrates its best performance when used for the measurement and control of the axial and surface vibration of rotational shafts such as main shaft of turbines, electric motors, compressors, and of the thickness and width of moving objects. In addition to the measurement of the amount of displacement, a gap detector can also be used for a wide range of other measurement and control applications such as the measurement of the amount of slack or warping. The non-contact measurement process enables to apply no load to rotational or vibration body, and does not affect the material under measurement.
-
Product
XCITE 1200T Torsional Series
-
The Xcite 1200T Continuous Torsional Exciters provide high inertial torque in the frequency ranges required to excite steam turbine rotors, deisel engine crankshafts, and ship power drive trains. The speed range of up to 3600 RPM for the 1200T-9 and 7500 RPM for the 1200T-10 system is ideal for testing a broad range of rotating power generation equipment.
-
Product
Large Electrical Machines Bench Testing
-
The automated system for recording parameters during testing of gas turbine generators consists of several independent but interacting measuring subsystems and a signal conditioning system. The subsystems for recording "fast" signals are implemented on the PXI platform, "slow" signals are registered by a subsystem built on the basis of the Compact FieldPoint platform.
-
Product
Torque Measurement System
-
Torque measurement system is intended for periodical control and endurance testing of various moving structural elements, e.g. turbine blades, etc.
-
Product
Capacitor for AC Filtering
PECA4 (900V)
-
Lifasa - International Capacitors, SA
These capacitors are especially suitable for applications where high levels of AC voltage are required. The design of this series has been optimized for the manufacture of high performance AC filters for compensation equipment with high pollution such as UPS or wind turbines
-
Product
Wind Power Solution
NXA GAMESA
-
The NXA GAMESA is custom-made with firmware and fixtures designed specifically for Gamesa turbines: G80x, G90x, G114, G126, G132, G145. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Wind-Solar Hybrid Generator
-
FD-200W (300W) Small wind turbines suitable for wind resource is better to ensure electricity inconvenience areas or occasions, especially combined into scenery complementary power supply system, may be partially or completely replace electricity to meet its rated Output power range of all kinds of electrical power requirements. Small size, light weight, low wind speed Cut the use of maintenance-free, high reliability and easy to install set up, working and long life and so on.
-
Product
Wind Power Solution
EVO ACCIONA
-
The EVO ACCIONA is custom-made with firmware and fixtures designed specifically for Acciona turbines. These precisely designed fixtures make generator-to-gearbox alignment easy inside any nacelle – safeguarding reliability and optimizing the energy efficiency of the wind turbine.
-
Product
Comprehensive Oil Analyzer For Engines
MiniLab EL
-
Engine oil analysis is a reliable and mature non-destructive testing (NDT) technique used to monitor the condition of the engine in development, on the production line and for in-service maintenance. High performance reciprocating engines and jet turbines are complicated mechanical systems with many high speed moving parts.
-
Product
Engine Test Systems
TITAN Engine
-
The TITAN engine test system series contains fully equipped engine test stands which are designed for various categories of internal combustion engines, ranging from light-to heavy-duty engines and also offering solutions for component tests such as testing the exhaust line. Further adjustment for off-road engines, powered two-wheeler engines, small internal combustion engines from carts, snowmobiles or motorboats as well as aircraft turbines are available. Additionally, it is also possible to test alternative engine concepts.
-
Product
Exhaust Gas Thermocouple
LM2500 T5.4
-
AMETEK is the original OEM for the T5.4 EGT. We supply the L44830P01, L44830P02 and L44830P03 probes for use on the LM2500, LM2500+ and LM5000 gas turbines. In addition to the EGT, we also provide rigid harness, T3 probes, cables and flexible harness for these engines. Ensure you get the highest quality by selecting OEM qualified parts to keep your engine running reliably.
-
Product
Engine Simulator
MS 1118
-
Test Set-A calibration unit is a test jig is used to simulate parameters of Adour 804E and 811 engines of Jaguar aircrafts. It simulates current, voltage, speed, and turbine gas temperature. It performs NL Check, NH Check, TGT1 (Non T2 Compensated), TGT2 (T2 Compensated), Amp (Non T2 Compensated), Amp (T2 Compensated), Solenoid Volt, TGT Inject, NL Inject, and NL/TGT Redatum.
-
Product
Turbine Flow Meters
-
Turbine flow meters are the most popular choice to measure flow electronically. They offer a wide flow and application rangeability. Turbine Flow Meters are easy to maintain, durable and versatile.
-
Product
Exhaust Gas Temperature Thermocouple
LM6000 T4.8
-
The latest and most capable LM6000 gas turbine exhaust gas temperature (EGT) probe from AMETEK offers the longest possible life. AMETEK is the original EGT probe supplier for CF6 aircraft engines. LM2500, LM5000, and LM6000 industrial gas turbines and now brings to market an EGT probe with new materials and a new design. The latest LM6000 T4.8 EGT thermocouple is OEM qualified and incorporates, many improvements over any previous products. Materials are carefully selected to ensure long product life and superior performance. Specifically, a new single crystal alloy for the probe support significantly improves high temperature mechanical strength. In addition, the thermocouple sheath material increases high temperature oxidation and creep resistance. Best of all, AMETEK's new T4.8 thermocouple is completely interchangeable so that it can be used on all LM6000 applications.
-
Product
Bat Deterrent Systems
-
As White-Nose Syndrome continues to ravage the populations of many hibernating bat species, the wind industry remains committed to lessening its impact on wildlife, including contributing to bat fatalities. While it is well researched that wind turbines cause mortality to bats, successful minimization methods have been implemented. Presently, the most effective techniques involve curtailment, which requires a reduction in energy generation. NRG Systems understands that this is not an ideal option for wind plant operators, so we have set out to develop Bat Deterrent Systems that could significantly reduce bat take without curtailment, meaning operators can produce more renewable energy more of the time while keeping all bats out of harm’s way.
-
Product
Spring/Non-Spring-Loaded Thermocouple
8PT25
-
The AMETEK 8PT25 Spring/Non-Spring-Loaded Thermocouples for Frame 6, 7 and 9 applications have been designed, fully tested and qualified to meet OEM specifications. Power Instruments’ expertise in solving creep, stress rupture, corrosion, EMF drift and other problems affecting sensor performance has resulted in a robust line of single and dual element thermocouple designs. This thermocouple is immersed directly into the turbine fluid to monitor temperature while in operation.
-
Product
Capacitors - Power - Heavy Current (ESTA)
-
Vishay ESTA is one of the few manufacturers to offer a complete range of power capacitors. These cost-effective devices for harmonic control, energy savings, and voltage stabilization are highly reliable and environmentally safe, and can be used under the most rugged conditions. Vishay ESTA power capacitors address a wide range of energy-generation applications. Their “green” applications include energy generation in on- and off-shore wind turbines and solar power plants.
-
Product
Exhaust Gas Thermocouples
8TR4C Series
-
The AMETEK 8TR4C Series Exhaust Gas Thermocouples for Frame 7 and 9 applications have been designed, fully tested, and qualified to meet OEM specifications. AMETEK has worked closely with the OEM turbine manufacturer to qualify and engine test this thermocouple as a direct replacement, or for upgrading older style Exhaust Gas Thermocouples.
-
Product
PDS Pile Placement Monitoring Software
-
The Monopile Placement module is the result of the cooperation between our clients and our engineering and software teams.Monopiles are used in wind farms as a foundation upon which to place a wind turbine generator. The application monitors the process of the placement of the monopoles.
-
Product
AC Load Bank (Resistive & Inductive)
K-1000 Resistive & Inductive
-
Kongter Test & Measurement Co., Limited
Kongter resistive & inductive AC load banks are used to simulate the motor loads or other electromagnetic devices working at their rated power factor. Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit.
