-
product
Telemetry Signal Simulator
Model: DS-7240
The Telemetry Signal Simulator is intended for laboratory use in the testing of telemetry receiving systems. The unit features a fully synthesized signal source that can be set to any telemetry frequency in the 2200-2300 MHz band in 500 KHz steps. The simulator has an internal attenuator that can set the signal level from +10 dBm to 20 dBm in 1 dB steps.
-
product
Oscilloscope - 500 MHz, 2 Analog Channels
DSOX3052T
500 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
product
Test Equipment
Test Devices has developed the world’s most precise, accurate and efficient test solutions because the company employs very experienced and accomplished scientists and engineers. For almost 40 years Test Devices has developed and advanced the science of centrifugal, vibratory and thermal stress testing and measurement of rotational components – critical solutions engineers need to evaluate integrity and validate component parts.
-
product
Custom Systems
No two products or processing challenges are exactly alike. That’s why a specially-configured MAC® Custom System can help you address unique testing requirements…as well as the demands of your own internal standards
-
product
Microwave Testing
90
The PICOPROBE MODEL 90, a high performance microwave probe which incorporates a WR-12 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
product
USB-7856, Kintex-7 160T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device
782916-01
Kintex-7 160T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device - The USB‑7856 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑785...show more -
product
Frequency Converter Upwards
UPCONVERTER 10 GHz LXI
UPCONVERTER 10 GHz осуществляет программно управляемый перенос вверх спектра шириной 150 МГц, поступающего на вход сигнала, в любую точку спектрального диапазона от 10 МГц до 10 ГГц. Перенос спектра осуществляется по супергетеродинному принципу с тремя ступенями переноса. Благодаря этому во всем рабочем диапазоне спектра достигаются высокие уровни подавления несущей частоты и зеркального канала. Также UPCONVERTER 10 GHz обладает уникальной возможностью, не имеющей аналогов среди приборов подобно...show more -
product
Current, Voltage, Resistance
Solutions for the testing and calibration of current, voltage and resistance are used in industry (laboratories, production, workshops), in calibration service companies and in quality assurance. These instruments are portable and mobile and are particularly notable for their low measurement uncertainty and high scope of operation.
-
product
ExpressCard Compliance Testing
PCMCIA has developed the ExpressCard Compliance Program in order to assure compliance and interoperability in products using the ExpressCard logo. In order to participate in the ExpressCard Compliance Program, your company must be a member of PCMCIA. PCMCIA member company's products that pass the Compliance Program are added to the ExpressCard Resource Directory
-
product
EMC Test Software
emcware® 6.0
AR RF/Microwave Instrumentation
emcware® by AR RF/Microwave Instrumentation provides automated Electromagnetic Compatibility (EMC) testing and report generation for all types of users from corporate to professional test laboratories. Through its unique workflow and hundreds of predefined test profiles, allows EMC test engineers more test time through minimal training, and highly efficient equipment and test setup when compared to the competition.
-
product
ADI Test Fixture
TA-6500
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) typ...show more -
product
Microwave/RF Cable Test Assemblies
PHASEFLEX
For test applications that require precise, repeatable measurements, microwave/RF test assemblies from Gore provide excellent phase and amplitude stability with flexure. Our rugged, lightweight assemblies deliver reliable performance with longer service life and reduced equipment downtime resulting in lower costs for testing in laboratory, production and field test environments.
-
product
High Voltage Surge Comparison Test Set-Up
Relying on our years of experience in this industry, we are highly acclaimed for manufacturing and exporting High Voltage Surge Comparison Test Set-Up. With wide use in electrical and power generation sector, this equipment is available in different technical specifications and models. We manufacture this High Voltage Surge Comparison Test Set-Up in accordance with industry standards using high grade raw materials. We offer this testing equipment to clients at competitive price.
-
product
Test Automation Platform / LTE, GSM and WCDMA
MLT1600
The MLT1600 addresses the testing challenges of IoT products across multiple cellular radio technologies – such as GSM, WCDMA and LTE – with a 70-MHz to 6-GHz frequency range. With its portable design and small footprint, the MLT1600 leverages W2BI’s existing cloud-based test management platform to acquire on-demand test cases and publish test results as required across all test parameters.
-
product
Partial Discharge Tester (Dry Type)
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
product
Battery Boxes Testing Equipment
Battery boxes can be tested for faults by placing the box on a metal plate. By applying a test voltage to an electrode inside the box, the moulding can be checked thoroughly - particularly at the injection points - and any faults found. Defects will be identified by a spark passing from the electrode, through the defect itself, to earth (the conductive material placed outside the battery box.
-
product
Precision Measurement System
OmniMic V2
Updated software and improved hardwareCompact, portable, accurate, affordableIntuitive software—open the box, start testing in minutesPerfect for setting up home theater systemsOptimized for use with netbooks and laptopsAccurate response down to 5 Hz, fully calibrated, includes FRD fileFor professionals and hobbyists—design and tune speaker systems and arrays
-
product
Transformer Testing Instruments
Wuhan Huatian Electric Power Automation Co., Ltd.
Transformer Testing Instruments by HVTEST
-
product
3 Wire (Analogue) Earth Resistance Tester
4105 ER
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● In addition to facilitating for precision measurement, test leads for simplified two-wire measuring system also are supplied as standard accessories.● Battery operated.● Battery life indicator. ● Calibration performed with supplied test leads.
-
product
Logic Analyzer Probes
FS2354 & FS2355
The FS2354 and FS2355 are logic analyzer probes used to test DDR3 SO-DIMM memory modules. When used with the triggering and analysis capabilities of Keysight’s Logic Analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR3 SO-DIMM systems.
-
product
Spectrum Analyzer Modular AFM AXIe
The software and hardware complex "Modular Spectrum Analyzer AFM AXIe" for the analysis of RF signals with a frequency of up to 10 GHz is intended for use in automated testing programs, research in the frequency domain of periodic signals in the RF and microwave ranges, as well as for analyzing the parameters of signals with analog modulation (AM, World Cup, FM).
-
product
High-accuracy Multi-channel Battery Simulator
N83624 Series
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N83624 is a programmable battery simulator with low-power, multi-channel and high-accuracy, suitable for BMS/CMS testing. It is highly integrated, single device with up to 24 channels. Each channel is isolated, which is easy for any series-parallel connections. Users can set the voltage and current for each channel by programming software, which is flexible, easy to operate and can meet the needs of multi-channel and multi-data. The software can also provide curve charts, data analysis and report functions. N83624 is equipped with high-definition color LCD screen, available for local operation.
-
product
PXI High Density MUX BRIC, 8-Chan, 80-Pole
40-570-114
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow tes...show more -
product
Veterinary Hematology Analyzer
ABX Micros ESV 60
The Gold Standard of Veterinary Hematology Testing- Open Tube- 10 animal species- 8 or 18 parameters- 50 tests/hour- Highly compact and lightweight- Micro-sampling on whole blood: 10μL- Precise cellular identification through electronic impedance variation method- Haemoglobin measurement with photometry
-
product
FLuorescent Lamp And Ballast Tester
2210-20
Milwaukee Electric Tool Corporation
The Milwaukee 2210-20 Fluorescent Lighting Tester is a new to world tool that tests fluorescent lighting fixtures and cuts troubleshooting time in half. The Fluorescent Lighting Tester delivers complete Lamp, Ballast and Pin testing. Test Lamps before or after installing, and test without dismantling the fixtures.Recognized for its innovation, the 2210-20 Fluorescent Lighting Tester will dramatically improve the productivity of professional electricians and maintenance technicians. Instead of a “replace and hope” strategy, users can test their lighting fixtures faster and easier. The 2210-20 Fluorescent Lighting Tester solves a top residential, commercial and industrial application.
-
product
Non-Contact Voltage Testers
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
product
Battery Capacity Tester
BLU-T Series
Battery load bank BLU-T is a powerful and lightweight solution designed for condition assessment of telecommunication and radio equipment backup supply. This instrument can perform the battery capacity test on battery strings such as Pb, Li-ion, Ni-Cd, and others. It tests battery strings with voltages in the range of 0,9 – 70,5 V DC. As a special feature, the BLU110T model enables capacity testing of single PB, Ni-based as well as Li cells (with current up to 100 A).The capacity test is conduct...show more -
product
Electronic Load System
Electronic loads are required for testing fuel cells such as PEMFC, AFC, PAFC, MCFC, SOFC. These electronic loads are designed either in IGBT technology with power, current and voltage ranges according to specific requirements or in transistor technology. Electronic loads in IGBT technology are designed for high voltage ranges up to 900 V, current ranges up to 1000 A, and power ranges up to 480 kW.
-
product
HandyScope HS6-DIFF With EMI & SafeGround: 1 GS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-1000XMEG-W5
The powerful capabilities of the WiFiScope HS6-DIFF-1000XMEG EMI analyzer give the user the possibility to quickly perform a good EMI compliance test. With this cost effective test, time and money are saved by avoiding extra visits to expensive EMC testing facilities. The supplied EMI probe set TP-EMI-HS6 contains three magnetic field (H field) probes and one electric field (E field) probe. The tripod ensures that the probes can be positioned properly at the object under test.
-
product
Replacement Solder Tip Leadset for Use with D410/D610
Dx10-SI-HiTEMP
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
