-
product
Manual Test Stands
AMETEK Sensors, Test & Calibration
This manual test stand is ideal for tensile testing, compression testing, peel, and flexural testing. It may be equipped with a quick-action lever or precision hand wheel for controlling crosshead speed and travel.
-
product
Lightning Test
Lightning testing is used to determine the ability of externally mounted electrical and electronic equipment to withstand the direct effects of a lightning strike.
-
product
Resonant Frequency Testing
E-Meter MK II™
Determines resonant frequencies of the three modes of vibration. Material characteristics such as Youngs Modulus of Elasticity, Modulus of Rigidity, Poissons Ratio and Damping Constant can be calculated. Frequencies are automatically scanned in one of four ranges. The system can determine flexural resonance of concrete under accelerated freezing and thawing cycles and aggressive environments.
-
product
Water Quality Testing Instrument
GDYS-101SC
Water quality analysis meter, single element. Each model can test one element contained in water.
-
product
MPI Testing Solution
Since 2008, MPI’s LED tester has provided optical and electrical measurements. With mass production experience, tester functions include flexible recipe management, accurate calibration, and statistical analysis. Flexible configurations allow the customer to choose test equipment configurations from the spectrum meter, photo detector and source measurement unit in accordance with your specific requirements. With accurate controlling of each instrument and intelligent data analysis, our testers offer the most accurate measurement result for a wide variety of optical devices.
-
product
Battery & Electrical System Testing
12-0200
Vehicle Battery Systems fitted to modern cars require a complex system to control and maintain the best charge and discharge rates which not only ensures the longest in service life but also that systems such as Stop/Start operate correctly. The 12-0200 gives the operator access to all the functions complicated and time-consuming manufacturer scan tools have to perform the same function but in a fraction of the time. On average the total time required by the technician to reset a system will be 30 seconds.
-
product
PXI High Density MUX BRIC, 6-Chan, 80-Pole
40-570-113
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow tes...show more -
product
Product Testing And End Of Line
World-class integration of electronic test equipment, instrumentation, test fixtures, automation, load simulation,data acquisition, and software . In partnership with two major leaders in high-technology automation, three very capable machine shops, a custom cabling company, a rapid prototype circuit board fabrication house and two large automated sheet metal manufacturing facilities we offer custom process and test equipment designed and manufactured for convenience and precision. Each component of our systems is carefully consideredto provide you with maximum performance consistent with easy maintainability and long term return on your investment.
-
product
Moisture Meters for Restoration
Delmhorst pin and pinless moisture meters and thermo-hygrometers are a must for restoration professionals. Testing for moisture in building materials is the only way to evaluate the extent of water damage, monitor the drying progress, and verify the structure is dry before removing any drying equipment.
-
-
product
Infiniium S-Series High-Definition Oscilloscope: 6 GHz, 4 Analog Plus 16 Digital Channels
MSOS604A
6 GHz bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 6.8 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15" capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
product
Portable Converged Networks Test Set
TX Series
The VeEX TX product series offers a complete test solution for Next Generation of Transport, Metro and Carrier Ethernet Testing. Color graphical display assisted with touch panel enables users tapping through the test configuration and accessing complex overhead bits and bytes. Features include APS, TDM, pointer adjustment, pulse mask analysis, G.821/G.826/M.2100, histogram, and overhead access.
-
product
LETIS
Power amplifiers that are universally used for radiated immunity testing either cover the range below 1GHz or the range above 1GHz. This means that if the test requirement extends both sides of this 1GHz point, the power amplifier needs to be changed over. Genrally, this involves three connections... The LETIS handles all these connections automatically. Each is switched via a high performance RF relay under the control of a USB interface. Software issued with the Laplace Synthesisers automatically detects the presence of a LETIS and handles the switching automatically.
-
product
Video Test Generator
881E/882E-DP
The Teledyne LeCroy quantumdata 881E/882E test instruments with the DisplayPort 1.1 transmitter option is packed with features for video and audio testing of DisplayPort monitors and displays at pixel rates up to 268 MHz The 881E-DP version is a lower-cost version with the full DP transmitter functions necessary for testing modern displays on manufacturing production lines. The 882E-DP version includes all the features of the 881E-DP instrument but offers several feature upgrades that are not available for the 881E-DP version.
-
-
product
Power Module And Device Testing System
Dynamic and static test system Meet the power IPM module dynamic and static electrical parameters test
-
product
Cable & Antenna Analyzer - 2 MHz to 4.4 GHz
E7000L
The E7000L Cable & Antenna Analyzer provides all necessary measurement functions and performance to accurately diagnose and verify the site’s cable and antenna system and RF connectors, as well as basic fiber-feedline testing. Smaller and lighter than the E7000B, the E7000L is ideal for installation of wireless cell sites.
-
product
32 Channel Analog Comparator Module
DP-VXI-5106
DP-VXI-5106, is a 32 Channel Analog Comparator Module with 32 channels of differential analog window comparators. Each channel is provided with a window comparator as well as a Level Comparator , software selectable on an independent channel basis. All the 32 channels have been grouped into four groups of 8 channels each. This allows the user to configure the comparator module based on the application to initiate alarm action to exactly meet application requirements. Each Comparator channel can ...show more -
product
Max-Hand Durometer
Model 3000
The Max-Hand 3000 durometer is Rex Gauge Co.'s latest innovation for the testing of specimens with creep. The Max-Hand 3000 has a max- hand and an active hand for observing the creep characteristics of a specimen. What makes the Model 3000 unique is the magnetic-drag maximum reset mechanism. Available ASTM, DIN, ISO Types: A, D.
-
product
Precision Integrated Analog Front End, Controller, & PWM for Battery Test & Formation Systems
The AD8452 combines a precision analog front-end controller and switch mode power supply (SMPS), pulse-width modulator (PWM) driver into a single silicon platform for high volume battery testing and formation manufacturing. A precision instrumentation amplifier (in-amp) measures the battery charge/discharge current to better than ±0.1% accuracy, while an equally accurate difference amplifier measures the battery voltage. Internal laser trimmed resistor networks establish the in-amp and difference amplifier gains (66 V/V and 0.4 V/V, respectively), and stabilize the AD8452 performance across the rated operating temperature range.
-
product
Unit Testing
Hitex offers a unit testing service for C/C++ application source code using the well-known test tool TESSY. For this service, the customer provides their source code of the C/C++ functions to be tested, ideally along with the specifications of the functionality and comprehensive comments in the source code.
-
product
Motor Exhaust Gas Analyzer
MEXA-ONE
MEXA-ONE offers an intuitive user interface with a highly efficient hardware and software design.This results in increased testing efficiency and economical facility operation, while enhancing reliability and accuracy. These advancements are possible because the MEXA-ONE software employs new "HORIBA ONE PLATFORM". This platform integrates the test devices in an emission cell into a single user interface, increasing efficiency and optimizing user control over the entire testing process.
-
product
Material Testing
In order to meet the constantly increasing quality requirements for products and their materials, we at Zentro test our products in our in-house EMC laboratory.
-
product
Oil Test Set
7000
Cambridge Instruments & Engineering Co.
Ideal for speedy and accurate testing of Breakdown / withstand test of transformer and circuit breaker oil, in accordancewith IS 6792 : 1992 for oil testing.
-
product
LATCH UP Tester
Tokyo Electronics Trading Co., Ltd.
The purpose of Latch-up testing on your components is to verify their robustness against overvoltage/ overcurrent events during their operation.
-
product
PXI Precision Resistor Module 6-Channel, 2.5 to 102k
40-297-040
This 6-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Environmental Chamber
Qualitest Environmental Chambers are capable of simulating a wide range of temperature, humidity, and other environmental conditions. These environmental chambers are well-suited for use in electronic, military, and pharmaceutical quality assurance and reliability testing, as well as research testing and production processes.
-
product
Temperature & Pressure Switches
Pressure switches survive shock and vibration during all operating conditions and phases of flight and have been qualified to temperature conditions that exceed RTCA DC-160 requirements. Testing and design that goes above and beyond what is required has helped to make Measure Tech the "go to" manufacture when airlines need a new switch to help improve dispatch reliability.
-
product
Wireless Device Testing
D.L.S. Electronic Systems, Inc
WI the testing and certification of your Wireless Device will be accomplished with precision and efficiency.
-
product
System Level Test
SLT
As technology nodes continue to evolve and with a more aggressive time to market to bring devices to their end applications, full test coverage of such chips is possible only with System Level Testing.
