Showing recent results 1156 - 1170 of 4805 products found.
-
TCX 01 - Chauvin Arnoux Metrix
The TCX 01 surface-mount device tester automatically recognizes the component tested and displays its value on its large 6,000-count LCD screen. The TCX 01 recognizes resistors and capacitors, and can also perform junction and continuity tests.
-
ST-2300 - Wuhan Sunma Technologies Co., Ltd.
his Telephone Line Testeris a portable and intelligent line fault tester which is designed following human engineering theory with the appearance style like barbell, adopting advanced technologies such as intelligent CPU, IC & SMT technology.
-
43062 - LINDY-Elektronik GmbH
This HDMI cable tester is a compact, palm sized unit for testing HDMI cables. It can be used to read and check the pin-out configuration of cables before and after installation. A separate passive module is included for remote testing of pre-installed cables.
-
3095 - Elcometer Limited
Measuring a coating’s hardness using the indentation method, the Elcometer 3095 Buchholz Hardness Tester consists of a bevelled disc indenting tool which is fitted into a stainless steel block exerting a constant test load of 500g (17.6oz).
-
PA-01D - Pansco, Ltd
The LAN cable tester is a versatile, full-featured tool for testing many kinds of network cable. Loopback and remote tests may be performed automatically or manually, and will test cable continuity as well as identifying opens, shorts, reversed wiring, and miswiring in cables up to 2,000 ft. long. Shielded connectors allow the tester to test shielded twisted pair (STP) cables. The built-in tone generator generates a low emission frequency tone which can be detected by any market tone probe, making it easier to trace and locate cables. Uses 1 9V alkaline battery. CE Approved.
-
3520 - Rochelle Communications, Inc.
The Rochelle Model 3520 Modem-On-Hold Tester is a stand-alone instrument for development and testing of V.92 Modems and Integrated Access Devices. The Model 3520 features user-friendly software that allows the user to set CO line parameters, ringing voltage and frequency, and signal levels. The Model 3520 includes selectable 6, 9, and 15Kft artificial lines (26 AWG). Secondary CO line permits end-to-end voice path between two client modems. Pass-Through Mode places the CO-line simulator in series between a client modem and other testers or an external POTS line
-
Focus-275 - Kyoritsu Testsystem Co., Ltd.
Focus275 is a tester for burn-in board.It can improve reliability of burn-in board by inspecting boards for burn-in test by Focus275 regularlyBoth short open test and component test can be done by sending electric signals for special socket contactor and edge part.
-
TESTEX Testing Equipment Systems Ltd.
Button Impact Tester, to determine the impact resistance of plastic sew-through flange buttons to a falling mass of 0.84kg (29.5oz), released from a height of 67mm (2.625 inches) or other heights as required. Cracking, chipping or breakage constitutes failure.
-
TF144A - TESTEX Testing Equipment Systems Ltd.
Button Impact Tester, to determine the impact resistance of plastic sew-through flange buttons to a falling mass of 0.84kg (29.5oz), released from a height of 67mm (2.625 inches) or other heights as required. Cracking, chipping or breakage constitutes failure.
-
DPW Series - UDEYRAJ ELECTRICALS PRIVATE LIMITED
These portable testers have been designed to be used in testing high voltage equipment in power engineering. Routine testing of the insulation and leakage is a necessary requirement for surge arresters, cable breakdown testing, capacitor charging and other laboratory use.
-
SG-F11-2 - Jinge Testing Machine Co.,Ltd
Electric Twist Tester determines yarn twist in single or plyed yarns, quadrant type with auto stop & reverse for conventional or untwist/re-twist methods. Test length adjustable up to 50cm/20 inches for S & Z twist yarns.
-
TF143 - TESTEX Testing Equipment Systems Ltd.
Fryma Extension Tester, to simply and economically determine the stretch and recovery of textile fabrics, both knitted and woven. The apparatus consists of a loading frame with clamps and a screw tensioning device, two 3kg loading weights and sample cutting templates.
-
M450LT - Rod-L Electronics
Performs leakage current tests in compliance with IEC 601, UL 544, UL 2601 and other medical and non-medical standards. Add Rod-L Hipot & Ground Continuity testers to build a complete modular automatic test systerm
-
Guangzhou Amittari Instruments Co.Ltd
Screen Tension Tester applicable to general wire mesh tension and steel mesh tension measurement. Suitable for screen printing and screen stencil measurement, high accuracy. The ideal and necessary tool for production of precise screen and steel mesh.
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
GDGS different frequency automatic dielectric loss tester is a high-precision instrument, which can be applied to automatically measure electrical loss tangent ( ) and capacitance of all kinds of high voltage electrical equipments’ on the spot of power plants, substations etc.
