Showing product results. 571 - 585 of 5516 products found.
-
MS-158 - Misum Systech Co., Ltd.
This equipment is used for inspecting state of earphonethroughmeasurement of resistor, consumption current and sensivity. Depends on the setting value, OK or NG will displayed.
-
TAURUS PRECIOHM ET - Taurus Powertronics Systems
The TAURUS PRECIOHM ET is one of the specially designed products by TAURUS to measure earth resistivity and earth resistance in a power station. These tests are performed based on 4 point (Wenner) and 3 point (fall of potential) methods respectively. All electrical equipment in the substation and power stations are electrically connected to station earth mat with earth electrodes. The earth electrode ensures that in the event over voltage on the system due to system fault or lighting discharges etc., the parts of the equipment which are normally ”dead” as far as voltages are concerned; do not attain dangerously high potentials. An earth electrode will only be effective so long it has a low resistance to the earth and can carry large currents without deteriorating. Thus the resistance of earth electrode should be low to give good protection and it must be continuously measured and monitored in all the substations and power stations.
-
Kyoritsu Electrical Instruments Works, Ltd.
Earth Ground Testing. Most facilities have grounded electrical systems, so that in the event of a lightning strike or utility overvoltage, current will find a safe path to earth. A ground electrode provides the contact between the electrical system and the earth.
-
Sanwa Electric Instrument Co., Ltd
Most facilities have grounded electrical systems, so that in the event of a lightning strike or utility overvoltage, current will find a safe path to earth. A ground electrode provides the contact between the electrical system and the earth.
-
C.A 771 - Chauvin Arnoux Metrix
Compliant with IEC 61243-3, the C.A 771 VAT can be used to work on any 1,000 V CAT IV installation. It is rated IP65 and offers a type-S extended climatic class for indoor and outdoor use, including in extreme conditions.
-
VT14 - Chauvin Arnoux Metrix
12 V to 690 V voltage test (7 diodes)Indication of polarity by " + " and " – " diodesImpedance: 400 kΩOperating frequency: DC and 50/60 Hzovervoltage protection up to 1,000 VIEC 61010 600 V CAT IIIPowered by 1 x 9 V 6LR61 battery (supplied)
-
Fluke T6-1000 - Iconic Engineering Limited
We know operating in electrical boxes packed with wires may be difficult once you’re attempting to seek out a secure gold contact purpose. Now, with Fluke’s T6-600 or T6-1000 with integrated FieldSense technology, you'll be able to quickly and simply take measurements by slippery the open deliver a conductor to visualize the voltage level without the need for test leads.
-
C.A 732 - Chauvin Arnoux Metrix
With its built-in torch, the C.A 732 can be used even in the dark to test your electrical switchboard or RCDs!
-
C.A 773 - Chauvin Arnoux Metrix
The C.A 773 VAT is an essential tool for electricians to check that no voltage is present before working on any electrical installation connected to the network.
-
VT12 - Chauvin Arnoux Metrix
No-contact phase detection• Extra-bright LED torch• operating voltage: 200V to 600V AC 50/60 Hz• IEC 61010 600V CAT III• Powered by 2 x AAA/LR03 batteries (supplied)
-
Control Company
Designed specifically for easy and intuitive use. After one minute, you’ll never again look at the directions. LCD displays exactly which measurement is being made. Audible beep confirms each measurement. Three distance memories and one calculation memory are maintained even when the unit is off. Calculator function permits addition/subtraction of readings.
-
Precision Mastech Enterprises Co.
AC Voltage range: 50V-1000V AC, 50/60HzSafety standards: Designed to international safety standard IEC61010 - 1/600V CAT III, 1000V CAT II.Battery: 2*1.5V (AAA type)Altitude: <2000mOperating temperature: -10 to 50CStorage temperature: -20 to 60CHumidity: <85% relative humidityDimensions: 157*24*20 mmWeight: Approximately 42g
-
all-sun
This hand-held digital logic probe provides convenient and precise use in the measurement of logic circuits. It displays logic levels (high or low), pulses and voltage transients down to 25 nanoseconds. High intensity LED readouts provide instant response to the logic state. Tests all logic families TTL/LSI, and CMOS/MOS digital circuits.
-
ESM-1 - ROM-Elektronik GmbH
With the ESM-1, you can easily determine where your body is subjected to electrical alternating voltages without prior knowledge. In addition, you will see how your sanitation measures change your electrical load. In the past, multimeters have often been used for this purpose. As far as simpler devices were concerned, uncertainties of measurement were present and the results were often not comparable.
-
Metrue Inc.
Is used for evaluating the electrostatic immunity performance of electrical components and electronic equipment by simulating real electrostatic discharges. The maximum ESD voltage generated is 30 kV and meets the most severe standards’ requirements. Equipped with different modules or discharge guns, ITI-2030 can operate at different ESD test modes. When the static electrons run up to a certain extent, it will quickly discharge to a circumjacent object, which would cause damage to the electronic equipment or semiconductor components. An ESD generator is used for evaluating the electrostatic immunity performance of electrical components and electronic equipments by simulating the real electrostatic discharges.
