Showing product results. 4816 - 4830 of 5525 products found.
-
Chandler Engineering
Fluid Loss testers were designed to be as easy to use as possible, with clear and intuitive controls. Once the cement slurry or mud is placed into the test cell, a programmable temperature controller increases the temperature at the desired rate. The slurry is conditioned by stirring at 150 rpm similar to a consistometer.
-
Spectrum-9100™ - Teradyne, Inc.
The Spectrum-9100 is a fully integrated functional test system for factory, depot, and intermediate test applications. It’s the “go to” tester for users needing a mix of digital, analog, mixed-signal, and bus test capabilities across a wide range of products—from legacy boards to advanced systems.
-
Test Head Engineering, LLC
Test Head Engineering designs and builds high‐quality In‐Circuit Test (ICT) Fixtures for HP / Agilent / KeySight Technologies 3070 board testers. We partner with In Circuit Test Engineering, Inc. to provide turn-key 3070 ICT solutions - both fixture and programming.
-
MS 3646I - Meltronics Systemtech
Interface and Load Box is standard portable 19” rack mountable unit. It is customized unit for single channel tester of IFCC. This unit has cable/harness interface between CPCI System and IFCC LRU. This box also houses all actuator loads and switching circuits.
-
CAN-Bus Tester 2 - Gesellschaft für Mikroelektronikanwendung Chemnitz mbH
The CAN-Bus Tester 2 is a widely used measuring device for control of bus parameters. The success story starts already in year 2002 with the first model. The hardware was completely redesigned in version 2. The corresponding software is still developed and has been enhanced with extensive updates.
-
MD-1 Capa - Asker
High-precision measurement of micro-sized specimens with a Fully-automatic Micro Hardness IRHD System. simple operation. A hardness tester for thin and small specimens of various rubbers, thermoplastic elastomers, nonrigid plastics. Unlike conventional durometers, it enables direct measurement of the hardness of objects with higher reproducibility.
-
NetProbe 10G - NET Research Corp.
Multi-service Network and Telecom Analyzer. The NetProbe 10G is the latest introduction to NetProbe family of handheld testers. The NetProbe 10G comes with 10G Ethernet basic functionality as standard and can be software upgraded anytime with advanced 10G Ethernet, IPTV, VOIP, WIFI and IEEE C37.94 options.
-
TM590 - T&M Tools Limited Co
TM590 series Fiber Optic Multimeter is a newly designed tester, which integrates the optical power meter and optical light source function in one unit. It can separately work as power meter or light source; or simultaneously work as power meter and light source together.
-
VectorPort - Test Spectrum, Inc.
VectorPort is a versatile, low-cost test development tool for converting WGL or STIL vectors to targeted ATE tester formats, including pattern, timing, and pinmap data. VectorPort can read and write all major formats in both parallel (Flat) vectors and serial (SCAN) vectors.
-
FT4 - Freeman Technology
The FT4 Powder Rheometer® was designed with one purpose in mind - to characterise the rheology, or flow properties, of powders. This remains a primary function today, but the instrument, accessories and methodologies have been continuously developed to the point where the FT4 is now considered a universal powder tester.
-
T2000 - Advantest Corp.
SoC devices require small-lot high-mix manufacturing methods in the present era of rapid generation change. Semiconductor makers struggle with requirements to replace their testers on a 2-3 year cycle. The T2000 addresses their needs by enabling rapid response to market needs with minimum capital investment.
-
CTS - Teradyne, Inc.
The Spectrum-9100 is a fully integrated functional test system for factory, depot, and intermediate test applications. It’s the “go to” tester for users needing a mix of digital, analog, mixed-signal, and bus test capabilities across a wide range of products—from legacy boards to advanced systems.
-
9100 - Teradyne, Inc.
The Spectrum-9100 is a fully integrated functional test system for factory, depot, and intermediate test applications. It’s the “go to” tester for users needing a mix of digital, analog, mixed-signal, and bus test capabilities across a wide range of products—from legacy boards to advanced systems.
-
CZ5001 - Aegis Pty. Ltd.
Protect yourself and your employees by ensuring that your portable electrical appliances and equipment are tested for electrical safety to AS/NZS 3760:2010 with the CZ5001 Patrol Pro. The Aegis Patrol Pro is a reliable portable appliance tester (PAT) and is an essential piece of equipment for every workplace.
-
Primetest 50 - Di-Log
The Primetest 50 is the ideal tester for those looking for an easy to use portable Appliance checker. Simply choose Class I for earthed appliances, Class II for double insulated or mains cord test and the Primetest 50 will give a clear and simple indication of PASS or Fail.