Filter Results By:

Products

Applications

Manufacturers

Showing recent results 4741 - 4755 of 4817 products found.

  • Production Testing

    TechSAT GmbH

    ADS2 and TPM are often used in the development and integration phases of avionics products. Later in the product life cycle comprehensive production acceptance tests are required. It is easy to re-use already existing test cases when employing the same tools. Because our FAL Tester GUI software hides the test system complexity from the test operator, no high-level skills are required.

  • 200KHz AUTOMATIC TRANSFORMER TEST SYSTEM

    VE2729XAU - Vasavi Electronics

    Its a Microprocessor Based 200KHz Automatic Transformer Tester with inbuilt 20 Pin Channel Scanner for Automatic Switching and Testing Coils & Transformers (Ferrite) with Max. 20 PINS. Test Parameters : -> Inductance (L)-> Leakage Inductance (Lk)-> Capacitance (C)-> DC Resistance (Rdc)-> AC Resistance (Rac)-> Turns Ratio with Winding Polaity-> Quality Factor (Q)-> Impedance (Z)

  • Measuring Device for Testing the Effectiveness of Residual Current Protective Devices (RCD) According to DIN EN 61557-6 (VDE 0413-6)

    PeakTech Prüf- und Messtechnik GmbH

    A residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE).

  • Motorized Test Stand with PC Control

    35-10 - Testing Machines, Inc.

    The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMe force-based positioning - using your hand as your guide, push and pull on the force gauge or load cell to move the crosshead at a variable rate of speed.

  • Battery Cell Test System

    CT0550 - PEC N.V.

    The CT0550 is a 80-Channel Battery Tester, ideal for testing and evaluating cells. This test equipment is used for high volume testing such as repetitive cycling, incoming goods inspection and validation. 80 independent 5 V/50 A channels per rack. Parallel switching mode for high current applications. DYNAMIC linear electronic load. Ultra fast rise, fall and switching time between charging and discharging modes.

  • CEAST VisualMELT Software

    Instron

    VisualMELT Software is designed to control all the functions of the Modular Melt Flow Systems, from single-weight to multiple-weight tests. The software enables the user to manage all optional equipment, including the load cell, the automatic cutting device, and the motorized weight lifter. When working with a multi-weight tester, it is possible to set up and control single-weight or multi-weight tests, as well as define the order and number of weights to be applied.

  • Dimensional Calibration

    Alliance Calibration

    123 BLOCKS ANGLE BLOCKS BALL BAR BORE GAGE CALIPERS CHAMFER GAGES CMM'S COATING THICKNESS GAGES CYLINDER PLUGS DEPTH GAGES GAGE BLOCKS GO-NO-GO GAGES HARDNESS TESTERS HEIGHT GAGES INDICATORS LENGTH STANDARDS LEVELS MICROMETERS OPTICAL COMPARATORS PARALLELS PIN GAGES PROFILOMETERS RADIUS GAGES ROUGHNESS SPLINES THREAD RINGS THREAD PLUGS

  • Intelligence-Driven Data in Motion Analytics

    NikOS Everest - Niksun

    NIKSUN NikOS Everest provides highly flexible, automated views on the data specific to you. No longer is the visualization tied to the data. You have complete freedom to filter, display, visualize, export and even run analytics right within the Everest GUI itself without having to perform ad-hoc special studies to obtain the data you want. Early adopters and testers have attested to NikOS Everest's expert value in the continuously evolving and highly competitive security industry. "NIKSUN NikOS Everest is one of the most robust unified platforms among cybersecurity tools today, providing the ability to render data at every level from a macroscopic view down to each individual packet," said Dr. Peter Stephenson, Chief Technology Editor at SC Magazine. "Not only does NikOS Everest have the ability to pull up this information at rapid speeds, but it also makes it far simpler to view and classify that data than ever before."

  • Thermal Imaging System for Electronics Testing

    ETS320 - Teledyne FLIR

    FLIR engineered the ETS320 for thermal testing and analysis in electronic on electronic components and printed circuit boards (PCBs). It combines a high-sensitivity thermal camera with an adjustable table stand to provide consistent, non-contact thermal testing through the entire electronics design, development, and production process. With more than 76,000 points of temperature measurement, the FLIR ETS320 allows users to monitor thermal performance, detect hot spots, and identify potential points of failure during product development. The camera’s measurement accuracy and its ability to visualize small temperature differences help testers evaluate thermal performance, ensure environmental compatibility, and troubleshoot problems for a wide range of components. The rechargeable, battery-powered ETS320 sets up quickly and easily, so product developers can have an immediate, real-time view into the thermal performance of their designs. The unit comes fully assembled and ready to connect to a PC running FLIR Tools+ software for detailed data analysis, recording, and reporting.

  • Torque Reaction Sensor

    BMX - Mountz Inc.

    Meeting the demands to test multiple torque ranges for various torque tools used in production, maintenance and calibration labs, the versatile torque sensor is used in conjunction with a torque tester. The torque sensor is a bench mounted calibration instrument designed for torque wrench calibration, torque screwdriver calibration, and electric & pneumatic screwdriver calibration. Controlling torque is quintessential for companies to ensure their product's quality, safety and reliability isn't compromised.

  • High Precision LCR Meter

    MCR-5000 series - Matrix Technology Inc.

    MCR5000 series is a multifunctional LCR preci­sion meter used for testing various electronic components. Adopt 4.3-inch TFT LCD display, simple display, elegant layout. It is a high speed, wide band, 5 bit test resolution impedance measuring instrument with 40hz-200khz multi­pie frequency points and 0.1% accuracy, which can meet the requirements of component parameter detection in various occasions. Is a high - quality cost-effective tester.

  • Strength Meter

    NOVOTEST IPSM-U+T+D (Pulse Velocity Tester) - NovoTest

    The pulse velocity tester IPSM-U+T+D allows to measure the strength and homogeneity of the concrete, bricks and other materials under the composition and surface sounding in products and designs for construction projects, inspection of buildings and structures, according to ASTM C597-16 (Standard Test Method for Pulse Velocity Through Concrete).  Has the determining of the depth of cracks by the surface sounding probe function and also flaw detection mode (A-scan).

  • Hydraulic Test Systems

    Genuen

    Genuen specializes in hydraulic test stands, including component tests, pumps, motors, valves, actuators, fatigue, load frames, and burst testers. As an industry leader in custom test systems, we focus on hydraulic solutions that leverage off-the-shelf technologies for mechanical subsystems and components. Our hydraulic test equipment has been deployed in aerospace and defense, automotive, industrial, commercial, and many other industries.

  • Electrosurgery Analyzers

    Fluke Biomedical

    Electrosurgery Analyzer is the ESU tester you can depend on for complete preventive maintenance and electrosurgical device safety to completely test these critical functions:* Measures current, voltage and power output.* Tests RF leakage from output to ensure no hazardous currents are present.* Performs Return Electrode Monitoring (REM) tests.* Measures crest factor.* Performs automatic power distribution curve at a wide range of test loads.

  • Automatic Test System

    Chroma ATE Inc.

    Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.