Showing product results. 2491 - 2505 of 5378 products found.
-
Amida Technology, Inc.
AMIDA ATI 600 Tester is a dedicated test system for semiconductor components (MOSFET, BJT, DIODE, ... etc.), which can accurately and quickly measure product parameters through form filling and editable program control. In practical applications, AMIDA ATI 600 Tester is the best choice for users, whether it is CP or FT mass production testing, or research projects of component characteristics.
-
448 - SCI, Inc.
Our 448 model is a 4-in-1 tester with 500VA AC Hipot, DC Hipot, Insulation Resistance and Ground Bond testing capabilities. The 448 is capable of a 500VA AC Hipot output to comply with 100mA leakage current test compliance requirements. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application.
-
SG-F30 - Jinge Testing Machine Co.,Ltd
It is a textile fabrics-Testing method for assessing the degree of snagging This tester is a performance testing of the tester simulates silk knit anti- hook. Put a bead pillow into a testing sample , and then the samples containing beads knitted pillow into cylinder, this cylinder has a wall with rows and rows of needle. The rollers was rotating in a certain number of turns , after the test, the sample is completed the assessment snagging grade.
-
Extech VT30 - Extech Instruments Corporation
The VT30 is a voltage, continuity and phase tester with built in flashlight and backlit digital display with bar graph. The tester features a double molded IP64 housing, polarity detection with LEDs for positive and negative DC and a CAT III 600 Volt / CATIV 600 Volt safety rating. This product is complete with a one year warranty, 2 AAA batteries, protective cap, and pouch case.
-
H646 - Howell Instruments, Inc.
Designed for use with the C-130 aircraft, Howell's lightweight, portable H646 Compressor Discharge Pressure (CDP)/Bleed Tester accurately and efficiently
-
EFM-III - A&D Company, Ltd.
The measurement unit of A&D's conventional friction and wear tester has been adjusted to enable the measurement of friction characteristics with higher precision.
-
A291800-03 - Chroma ATE Inc.
The A291800 is an LVDS signal model that can be used with FPD Tester to provide LVDS panel standard signals and related controls for LVDS inspection.
-
HFIT 7.0 - MEDTEQ
The MEDTEQ high frequency insulation tester is a popular device for evaluating compliance with IEC 60601-2-2 and the characteristics of insulation at high frequency
-
FD116 - Shenzhen Leadsmt Technology Co.,Ltd
Features and Characteristics: Simultaneously test 16 products, while judging and recording the on-off times of each product ,normal testers can not do this .
-
EKT-100TRB - Ektron Tek Co., Ltd.
EKT-100TRB-Low Temperature Retraction Tester is designed in accordance with ASTM D1329, ISO 2921 with fully automatic and computerized controlling system.
-
-
UI-FT95 - Unuo Instruments
Ball Rebound Resilience Tester is used to test foam resilience by vertically dropping a steel ball on foam from required height.
-
QT-WVP - Qualitest International Inc.
Qualitest Water Vapor Permeability Tester QT-WVP series is used to test the water vapor transmission rate (WVTR) of packaging materials.
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
TF212 - TESTEX Testing Equipment Systems Ltd.
Wyzenbeek Abrasion Tester. Modern ergonomic design to determine the abrasion resistance of fabrics when rubbed against a standard abrasive or a wire mesh screen with a backward and forward motion over a curved surface. Wyzenbeek abrasion tester applies to automotive and furniture industry fabric manufacturers working to US Standards Motor driven with 4 abrasion heads and electronic digital counter to control the number of cycles.