Test Systems
group of interoperable devices whose integration perform a common test purpose.
See Also: Systems, Equipment, System Integrators, System Test, System Integration
-
product
FLUKE® Test Tools
Testwave LLC® has been selling, renting, calibrating and servicing Fluke Products for over seventeen years.
-
-
product
32-bit PCI Test Backplane
SKU-014-01
The 32-bit PCI Test Backplane was designed to support production testing/debugging of PCI-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into four 32-bit PCI slots via 7 ft CAT6 cable. The PCI backplane is a versatile platform that allows you to test up to 4 PCI boards at the same time, facilitates easy access to logic signals, provides hot-swap compatibility, and per-slot overcurrent protection.
-
product
Test Clips
Angled Nose allows tight hold on 66 blockUse on 110 block with jumper and bed of nailsUse on larger cables with single piercing nail
-
product
Electromagnetic Interference Test
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
product
Protective Relay Test Kit
PW460
PW460 Protective Relay Test Kit is the comprehensive protection relay testing equipment for all types of protective relays with high accuracy. This relay test kit has in-built output monitoring and recording function and supports testing IEC 61850 digital relay.
-
product
Monitoring Systems
Once a dynamic event is detected, the system instantly informs the control system or other external devices and acts as a digital recorder by capturing important data before and after the event. This information can be used to alert the operator to change process settings or schedule maintenance.
-
product
DOC Drawout Case Test Plug
The DOC Drawout Case Test Plug provides an easy way to measure current and provide test access to GE style drawout case relays and meters.The DOC features normally-closed internal contacts. Upon insertion into the case, it brings the internal drawout case contacts out for easier access. Current Measurement Probes serve to redirect current circuits without disturbing them. Disconnect pins can be used to disable specific contacts and short-circuit currents.
-
product
Snap Button Pull Test Machine
UI-TX01
Snap Button Pull Test Machine is used to test pull strength of ornaments on garment, toy, footwear and others including button, bow and etc. Snap button pull test is a must-do test especially for Baby and children’s clothing and shoes. The test aims to use to button snap pull tester with suitable grips to pull the ornament to know if the ornament would be pulled off garment or not. The ornament falling off or broken button may cause infants or children the risk of ingestion. The button pull test methods includes 16CFR1500.51-53, ASTM PS79-96, ASTM F963, EN 71-1，M&S P115A and etc.
-
product
VSAT Interception System
VSAT
VSAT Monitoring system is a state-of-the-art Automated Passive VSAT Interception capability designed to meet the aspirations of our customers, to enable them to intercept and process various VSAT networks and their terminals in an interactive and automated manner. The system is conceptualized in such a manner that it can be used for both searchings for new VSAT networks as well as monitoring the content of target VSAT networks, with real-time decoding/decryption and reconstruction of Intercepted...show more -
product
Short Test Pin Probe 13
CX-13
Shenzhen Chuangxin Instruments Co., Ltd.
Short Test Pin Probe 13 Used to test accessibility through enclosure openings per IEC, EN, UL and CSA Standards.
-
product
M81-SSM Synchronous Source Measure System
The Lake Shore MeasureReady™ M81-SSM (Synchronous Source and Measure) system provides a confident and straightforward approach for advanced measurement applications. The M81-SSM is designed to eliminate the complexity of multiple function-specific instrumentation setups, combining the convenience of DC and AC sourcing with DC and AC measurement, including a lock‑in’s sensitivity and measurement performance.
-
product
Leakage Test
Leakage current and discharge current depend on the insulation of the device. The measurement simulates various fault situations that could occur during operation. The test determines whether the measured current is within the permissible limits and poses no danger to the user in case of a fault.
-
product
Backplane Profiling & Inspection System
603d
A major problem in the backplane industry is detecting bent connector pin defects. The most difficult being when the pin bends underneath the shroud rather than going into the hole. Many times this defect cannot be detected electrically as the connector pin is touching the conductive annular ring of the hole, allowing electrical test to pass. Unfortunately, it is an intermittent connection and will fail later on as there is not an actual mechanical connection.
-
product
Code Verification Systems for Quality Inspection
Matrix codes enable the comprehensive and seamless traceability of goods, which turns out as significant advantage considering everyday product recalls across all industries. Whether salmonella in food, contaminated cosmetics or poor components: defective products can harm consumers, cause losses of image as well as massive economic losses. Using the 2D code, each individual article can be localized globally. Based on the specific serial number, producers and consumers can clearly identify artic...show more -
product
Custom & OEM Light Measurement Systems
International Light Technologies
ILT has been designing and developing light measurement systems since 1965. We are a trusted partner to our OEMs in all facets of industry, and deliver solutions to companies in UV curing, disinfection, phototherapy, laser-UV-blue-IR safety, 3D printing, pulsed light measurement, and much, much more.
-
product
Temperature Humidity Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Battery high low temperature test chamber is designed to test all types of batteries, including lithium-ion batteries. The battery test chamber has many safety functions built into the test chamber, which can handle battery tests and prevent safety accidents. Charge/discharge cycle testing, which determines the number of times a battery can be used by evaluating it until it deteriorates after repeated cycles of charging and discharging. In the laboratories involved in battery testing, tests base...show more -
product
Motor Test for Electric Scooters
*The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA ...show more -
product
Walk-In Xenon Lamp Weathering Test Chamber
Xenon is one of the noble gases and is a major component of arc lamps and flash lamp and it also has its importance in general anesthetics. One of the major applications of xenon lamp is that it can be used in research applications to simulate the sunlight.Weiber walk in xenon lamp chamber uses xenon lamp to simulate the whole sunlight spectrum that can produce many destructive effects on the products. This simulation environment provided in the chamber is used to test the resistance of various ...show more -
product
Gas Chromatograph Test
Guangzhou Biaoji Packaging Equipment Co., Ltd.
Gas Chromatograph test the smell and solvent residues of printed packaging materials and test the quality and purity of the solvent.
-
product
Automotive Audio Bus (A²B) Analyzer System
A simulation and analysis solution for automotive audio networks based on the emerging Automotive Audio Bus® standard. The A2B Analyzer System is designed specifically for development teams servicing automotive OEMs, Tier 1s, and audio connectivity equipment suppliers. The deterministic nature of the A2B technology makes it particularly well-suited for automotive audio devices (active speakers, microphones) and newer applications such as Active Noise Cancellation (ANC), In-car Communications, etc.
-
product
Wide-Field FLIM System
LINCam FLIM
*Easy to Use Like an Ordinal Megapixel CCD Camera*Spatial Resolution ~ 1024 x 1024 Pixels*Temporal Resolution (IRF Width) 50 ps FWHM*Single-Photon Sensitivity*Saturated Count Rate Up to 5 MHz*Excitation by bh BDS-SM Family ps Diode Laser*Works with All Commonly Used MicroscopesI*llumination via Single-Mode Fiber*Lens System for Image Transfer Into Camera
-
product
Broadband Test
458-3SLB
This compact, versatile unit accepts 1, 2 or 3 line modules or other products that use Telebyte's convenient line module form factor. At home in the lab or a high-volume production environment, it is capable of controlling from 1 - 24 channels and is ideal for testing DSL modems and other bandwidth-compliant telecom devices. While it can be used as a stand-alone unit, the built-in Control Module interfaces with a PC via RS-232, IEEE-488, or Ethernet. In addition, the 458 Universal GUI (included with purchase) may be used to control the unit from a PC. For added convenience, the Control Module firmware is field-upgradeable through the RS-232 port.
-
product
Acoustic Emission (AE) Monitoring System
Sensor Highway II System
The Sensor Highway II System™ is an Acoustic Emission (AE) monitoring system with up to 16 high-speed channels and 16 standard parametric input channels (expandable to over 100). The system is designed for unattended and remote monitoring use in Structural Health Monitoring management and condition monitoring applications. It is rated for outdoor use and comes equipped in a rugged weather proof NEMA 4 enclosure.
-
product
BGA Socket And BGA Adapter Systems
Mill-Max's BGA Socket/Adapter Systems are used for both socketing BGA devices and interconnecting circuit boards. Systems are available to fit 1mm, .050" and .8mm grid footprints.
-
product
Particle Impact Noise Detection (PIND) Test
This test detects the presence of free moving particulate contaminants within sealed cavity devices. This test is specifically directed toward relays and other devices where internal mechanism noise makes rejection exclusively by threshold level impractical. This test method also may be used prior to final sealing in the manufacturing sequence as a means of eliminating loose particles from the interior of the device.
-
product
Wireless Billet Scale System
SW888RFX™
Displays Setups to One Hundredth of a Percent! Fully Integrated RFX Wireless Weighing Technology the most widely used advanced weighing technology of its kind and is used by champions in all forms of motorsports.
-
product
Plasma Processing Systems
PlasmaSTAR
The PlasmaSTAR® Series of Plasma Processing Systems from Axic, Inc. defines a new concept in barrel plasma processing. The systems are based on a modular design concept. Starting with a universal base unit, multiple electrode modules are available for easy insertion into the base unit. You will find the ease of use, variety of plasma processes, serviceability and attractive pricing unsurpassed by any other plasma.
-
product
Data Acquisition (DAQ) And Real-time Control Systems
Our data acquisition devices are capable of storing hundreds of analog and digital channels at full speed while allowing in parallel data to be sent out in real-time to any 3rd party EtherCAT master controller. We have brought the worlds of data acquisition and real-time control closer together which will save you time and money in a big way.
-
product
Monitoring System
A112
The photoelectric sensor model A112 allows to realize a system for detecting breaks of thin wires from 10 um in diameter, with a detection range greater than 50 cm.The A112 produces these results without the use of laser technology, allowing high immunity to vibration and a secure alignment between receiver and transmitter.
