Systems
are interconnected groups of purpose.
See Also: Equipment, Test Systems, System Integrators, System Test
-
product
Intelligent, Single- or Dual-Channel MIL-STD-1760 Adapter
EXC-1553UNET/Px-1760
The EXC-1553UNET/Px-1760 is an intelligent, single- or dual-channel, MIL-STD-1760 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1760 bus, both in the lab and in the field.The EXC-1553UNET/Px-1760 shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple ...show more -
product
ATX Power Supply Tester
Dr.Power II
Thermaltake Technology Co., Ltd.
Designed from the ground-up, it supports every ATX power supply available today up to ATX12V v2.3. - Oversized LCD panel that accurately shows the value of each specific power rails (within one-tenth of a volt). - Accurate voltage indicating for +12V/+5V/+3.3V/5VSB/-12V. - Built-in output connectors diagnostic system, low-voltage, high-voltage, no voltage, PG alarm systems.
-
product
Compact Cable Test Van
ETL-8
Van-based cable test and fault location system ETL-8 is used for testing cable insulation and locating cable faults using a variety of methods.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 2.5Ω to 102kΩ
40-252-040
The 40-252-040 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 102kΩ with 0.125Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PED Systems
Pulsed Electron Deposition
Is a process in which a pulsed (80-100 ns) high power electron beam (~1000 A, 15 kV) penetrates approximately 1 μm into the target resulting in a rapid evaporation of target material. The non-equilibrium heating of the target facilitates stoichiometric ablation of the target material. Under optimum conditions, the target stoichiometry is preserved in the deposited films. All solid state materials – metals, semiconductors and insulators, including those transparent to laser wavelengths in PLD – can be deposited as thin films with PED. By combining PLD and PED, the range of complex materials that can be prepared as thin films can be greatly enhanced.
-
product
Power Supplies
I-400
The I-400 power supplies are durable, practical, and efficient. Remove all superfluous attachments and features. The I-400 can provide reliability and 400 watts of power you can depend on to run your system. With its 80mm silent cooling fan designed for fastest cooling time and minimal noise level; you won't have to worry about overheating and noisy fans anymore. This is the basic power supply for casual users who just needs something that is cost effective and works.
-
product
Autoranging System DC Power Supply, 80 V, 340 A, 10000 W, 400 VAC
N8945A
The Keysight N8900 Series is a family of 5 kW, 10 kW, and 15 kW autoranging, single-output power supplies available in 14 different voltage, current, and power combinations and either 208 VAC or 400 VAC (28 total models).
-
product
Phantom Gravity Metal Detector
Phantom Gravity metal detector systems are designed to detect metal contamination in dry, powdery or granular free-flowing products that can be gravity fed through a pipe. Systems are available in Aluminum or Stainless Steel casings, with a selection of pipe sizes. The Diverter Valve reject system is typically used to divert contaminated product into a reject tank.
-
product
Electronic Circuit Simulator
SimOne
SimOne lets you perform full-featured electronic circuit simulation using state-of-the-art and classic modeling algorithms while taking full advantage of modern computers.SimOne does all the basic circuit analyses common to SPICE modeling systems and as well provides important Stability analysis.
-
product
Heat, Vapor, and Carbon-Dioxide Flux Sensors
Heat, vapor, and carbon-dioxide flux sensors are typically used in eddy-covariance systems to measure exchanges of carbon dioxide, water vapor, and heat between the surface of the earth and the atmosphere.
-
product
Input Modules
A Range of Input Modules To Support Most ApplicationsMix and match input modules for even greater flexibility. Up to 4 modules can be installed in the Synergy portable or Qb, 8 modules in the Synergy 8 and 16 modules in the Synergy Rack system.
-
product
ATE Computer
MS 1201
This system used for multi-purpose applications such as data acquisition and Automatic Test Equipment. ATE Computer has ISA Bus based eleven slots with inbuilt power supply. Micro Processor board or USB Controller is used to drive the back plane.
-
product
Multichannel Grating Spectrometer
PoliSpectra® Quad
Horiba’s OEM Polispectra Quad spectrometer is an integration of four VS70 spectrometers built around Horiba JY Type-IV flat-field aberration-corrected holographic concave gratings. This high throughput VIS spectrometer with 4 fiber inputs provides simultaneous acquisition of 4 channels at high speed with minimal crosstalk. The main electronics board is designed to read the two CCDs on the system simultaneously and provides 1-8X binning capability. This OEM system is a unique and innovative approach to drastically reduce the cost per channel.
-
product
AS-Interface Masters
*Simplified system installation by means of AS-Interface wiring system*AS-Interface - perfectly complements for different field buses or industrial Ethernet*Graphic user interfaces for clear configuration and diagnostics*High-performance controllers and gateways
-
product
Video Autoselector
1154A
Consumers who own a receiver and/or TV with limited inputs can use the 1154A to add multiple A/V sources. Its exclusive Adaptive Signal SensingTM technology uses multiple criteria to decide when to switch sources, and adapts to users’ activity patterns, customizing its switching behavior over time. The high bandwidth circuitry accepts HDTV component video (YPbPr), stereo analog audio, and digital audio in both optical and coaxial formats, and switches all audio and video signals simultaneously w...show more -
product
Electronic Yarn Count System
Y006
Consists of an electronic balance (220 grams x 0.001 grams) with internal and external custom software which calculates yarn, sliver and roving counts as well as fabric yield in various systems and provides statistics on any number of tests including totals, average, CV and SD
-
product
X-ray Inspection System
NEO-690Z / NEO-890Z
Off-line Microfocus X-ray Inspection System equipped with PONY ORIGINAL Direct Conversion X-ray Camera; SID-A50. Suitable for inspection of BGA, CSP, and LGA on PCB.
-
product
Antenna Positioning
Our SATCOM antenna systems provide non-stop gate-to-gate in-flight connectivity for commercial air transport, business jet and various military applications.
-
product
PCI Precision Resistor Card 6-Channel, 2.5Ω To 102kΩ
50-297-040
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Test Systems
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
product
SATA SSDs & Modules
Curtiss-Wright Defense Solutions
Curtiss-Wright direct-attached storage (DAS) products enable solid-state and rotating media to be incorporated in embedded computing VPX and VXS system solutions for a wide range of applications. Direct attached storage enables data storage devices to attach directly to the host. These data solutions are scalable, which enables the storage of your critical data from multiple Gigabytes up to 64 Terabytes. In addition, some direct-attached storage products feature encryption and sanitization capabilities, like AES-256, allowing you to keep your sensitive data protected.
-
product
Telemetry Receivers
Advanced Telemetrics International
ATi manufactures a wide range of telemetry receivers for use with our systems. Single channel, multi-channel and multiplexing telemetry receivers are available in various configurations, depending on the application.
-
product
Automatic Tablet Weighing System
CIW 7.2/7.3
With the automatic weighing system CIW 7.2 / 7.3 LAB you weigh tablets, dragees, capsules and similar products. Based on the UTS tablet testing systems by Kraemer Elektronik, the standard unit offers a tablet separation system and a special transport star for precise positioning of the test specimen on the integrated scale.The CIW 7.2 / 7.3 LAB in the laboratory version is now equipped with the database-driven, intuitive all-in-one touch software and no longer requires additional software soluti...show more -
product
Multiport Electromechanical Coaxial Switch, DC to 40 GHz, SP4T
87104D
The Keysight 87104D multiport switch improves signal accuracy in RF and microwave signal routing and testing applications. This high performance electromechanical switch provides unmatched isolation and a 0.03 dB insertion loss repeatability, which is warranted for the 5-million life cycle of the switch. The 87104D’s low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy. The repeatability and reliability of this switch guar...show more -
product
Static Frequency Converter Systems
Our software and connectivity devices incorporate all the features you need to proactively manage your systems, from basic monitoring and shutdown to predictive analysis and power management. Aplab Integration Services offer complete solutions tailored for the specific requirements of Defense Services, Telecom and Commercial markets.
-
product
Fiber Optic Test Kits & Sets
Amphenol Fiber Systems International
Amphenol Fiber Systems International (AFSI) has selected test equipment that is ideal for the field technicians who install and test our products. We offer a wide range of test equipment that meets our customers needs, including the periodic installer to the rugged field requirements for the US Army and USMC deployed or depot maintenance personnel to the advanced requirements of the Navy Shipboard installer requiring Navy approved test sets.
-
product
Dual Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-102
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Vessel-mounted
Our vessel-mounted systems are truly the state of the art. These acoustic systems, available in a diverse number of functionalities and profiling ranges, are renowned for their outstanding bottom-tracking performance and ability to measure currents precisely. Whether aiding survey and research vessels or assisting operators in making informed decisions in areas with strong current flows, our tools ensure optimal performance and reliability.
-
product
Aerospace Onboard Software Modules
ADS2 for Aerospace
Your product description goes here. The Aerospace Onboard System Development Process is guided by SAE ARP4754A. It consists of multiple levels of specification, design, validation and verification and is distributed between OEM and multiple suppliers of systems, subsystems and components.Due to the complexity of the development process, a consistent platform supporting model based validation, virtual and physical integration as well as requirement based verification at each level is of great importance for the industry.
-
product
Test Solutions For Integrators
Beyond being your test equipment expert, Testek can also provide engineering design advice and guidance on building complete test solution facilities. We will work closely with your building contractor to advise on the most optimal layout configuration and to specify all facility resource requirements. For systems that may share resources, we can facilitate resource demand and management, including power management and fluid management. With a central control system, we can provide software logic to monitor these resources and route them appropriately based on demand and priority.
