Systems
are interconnected groups of purpose.
See Also: Equipment, Test Systems, System Integrators, System Test
-
product
Erichsen Metal Sheet Testing Machine for FLC, FLD
GBW-600
Jinan Testing Equipment IE Corporation
GBW series Erichsen Metal Sheet Testing Machine is designed on the basis of screw universal material testing machine, using the servo motor for highly accurate loading for punching, meanwhile, it is equipped with hydraulic servo control system for pre-tightening/clamping of metal sheet. It is ideal to evaluate the plastic deformation performance and ductility of metal sheet & strip materials. The cupping test for metal sheet thickness range is 0.1mm-5mm, Max. Punching capacity is 600KN, and the pre-tightening/clamping device is with hydraulic servo loading pump for 600kN capacity;
-
product
Twin columns automated force test stand 36" travel - 2000lb
702SN
The advanced 702SN Series Universal Test Systems are ball screw driven test stands, excellent for affordable, precision tensile and compression testing of a wide variety of materials, products or ASTM standards. These variable speed testers have increased speed ranges and include adjustable travel limit switches. With the unique dual testing area, users can setup for two tests, tensile and/or compression, without having to switch out fixtures.
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 470Ω
50-298-114
The 50-298-114 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 470Ω with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Test Block & Plug Systems
Test Block system is an evolution of the 14 test circuit versions widely employed in the power utility sector. The primary difference is the incorporation of ‘finger safe’ test sockets which allow the use of shrouded 4mm banana plugs.
-
product
Multiport Coaxial Switch, DC to 20 GHz, SP4T
87204B
The Keysight 87204B terminated multiport switch provides the life and reliability required for automated test and measurement, signal monitoring and routing applications. Innovative design and careful process control created the Keysight 87204B which meet the requirements for highly repeatable switching elements in test instruments and switching interfaces. The Keysight 87204B is designed to operate for more than 10 million cycles. The exceptional 0.03 dB insertion loss repeatability is warrante...show more -
product
Online Water Quality Monitor
TW-150
HORIBA's TW-150 is a process water quality measurement system designed for drinking water and water distribution plants. TW-150 monitors turbidity,color, free residual chlorine, water pressure and pH without any reagent for measurement.This chemical free method reduces operating costs as it requires minimal maintenance and improves process control.
-
product
Impedance Analyser Frequency Response Analyser
C60
The C60 investigates the opaque world of analog networks. The unit operates in two test modes. It can measure the frequency response of a two port system producing a gain/loss and phase graph. It can also measure the reactive response of a two terminal network producing an impedance/admittance and phase graph. Electronic, electrical, electro-acoustic and other networks can be tested with sine wave excitation and the results displayed on a PC.
-
product
DC Rechargeable Power Source
PDX-X00L Series
PDX-X00L series rechargeable lithium batteries are the latest developments based on the fully considerations of the customer’s requirements which features with high capacity, high safety and multi-voltage output. This battery designed with button switcher to switching the output voltage freely, that is more safe and portable.Works with the Geo-electrical system, it is available to ensure a long time continuous field work.
-
product
PXI 2A Multiplexer, 1-Bank, 16-Channel 8-Pole
40-614-018
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
Data Acquisition Systems & Instruments
Whatever your application, mobile or stationary, on a test cell or under extreme environmental conditions, HBM has the right measurement data acquisition system for your needs.
-
product
ESD & Latch-Up Test System
Identify and help correct ESD and latch-up susceptibility issues on sensitive integrated circuit components prior to full-scale production with the Thermo Scientific™ MK.2-SE ESD and Latch-Up Test System. The MK.2-SE test system provides advanced capabilities to test high pin count IC devices to Human Body Model (HBM) and Machine Model (MM) ESD standards. The system’s pulse delivery design addresses wave form hazards such as trailing pulse and pre-discharge voltage rise, and performs Latch-Up testing per the JEDEC EIA/JESD 78 Method.
-
product
Vibration Test Chambers
Our vibration test chambers offer a variety of solutions for vibration testing. AV-Series and CV-Series vibration chambers offer rapid temperature change rates with combined temperature, humidity, and/or vibration environments. These chambers are designed for compatibility with your choice of electrodynamic or mechanical vibration systems. The Benchtop Vibration Table, ideal for vibration testing of small components or electronics and is designed for stand-alone testing or may be placed in an environmental chamber for combined temperature and vibration testing. HALT/HASS Test Chambers provide extreme vibration and temperature capabilities in order to identify design and product weaknesses.
-
product
Maintenance & Test Equipment
To minimize Life Cycle Cost of products and systems it is important to perform maintenance at exactly the right moment: not too early when the product has enough remaining lifetime and not too late when the lifetime is over. Mors Smitt offers a comprehensive set of maintenance and test equipment for in-service inspection, fault finding, and verification of relay conditions for optimum Life Cycle Cost.
-
product
PXI & LXI Simulation Tools
Our PXI & LXI simulation tools help you to accelerate the development process by simulating the product in your test system. These tools allow you to develop and test the system software independent from your application hardware. By using the tools, you can minimize the time required with the physical system.
-
product
PXI Very High Density Multiplexer, 24-Channel, 8-Pole
40-675A-002-24/8
The 40-675A-002-24/8 is a 24-channel, 8-pole MUX and is part of our range of PXI very high density low cost multiplexer modules. These modules are suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
product
Precision Impedance Analyzer (10Hz to 130MHz)
ST2851
ST2851 series precision impedance analyzer is a new generation impedance test instrument by adopting the current international advanced automatic balance bridge principle. It is based on Windows10 operating system, which realizes a fully computerized operation interface, making the measurement more intelligent and easier.ST2851 series impedance analyzer surpasses the 120MHz frequency bottleneck of similar foreign instruments, and solves the defect that it can only be analyzed but cannot be tested independently. At the same time, it adopts two interfaces of single test and analysis to make the test easier.
-
product
Osprey / TXP Co-Processor
9740-T
Triple+ speed Windows/NT Osprey Co-Processor for five times the system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory. Includes FPJ11® compatible hardware floating point. Performance equivalent 3.8 times the DCJ-11® and 130% of FPJ-11. On-card x86 microprocessor rapidly processes "virtual" I/O instructions. PCI bus speeds increase disk throughput by at least a factor of ...show more -
product
RX Pre-Amplifier System
RAM-34
The RAM-34 is a complete pre-amplifier system designed primarily for the low bands 160M thru 40M. It has inputs for four receive antennas and internal 3-pole bandpass filters for 160M, 80M and 40M. In addition to the pre-amplifier, it has a step attenuator that togetherwith the amplifier stage provides gains from -20 dB to +20 dB in 5 dB steps. This allows equalizing the signal levels between the antenna inputs. Gain settings are memorized for each antenna on each band. Different types of receive antennas have different signal levels and the gain memories eliminate the need to adjust the receiver or pre-amplifier when switching between the antennas.
-
product
THT AOI
Mek THT AOI overcomes these challenges of automated through-hole inspection with a unique combination of mechanical, optical and software design alternatives, unavailable in many conventional systems.
-
product
Miniature IC Handler
3270
Chroma 3620 is an innovative system handler for high-volume multi-site IC testing, especially for CIS Testing, at the system level.
-
product
ISC-1782, 2 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785150-01
The ISC‑1782 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all-in-one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic ...show more -
product
PXI 2A Multiplexer, 1-Bank, 128-Channel 1-Pole
40-614-015
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
product
Modular Spectrometers
B&W Tek boasts one of the most comprehensive lines of UV, Vis and NIR spectrometer modules on the market. Combined with our wide selection of spectroscopy accessories, we offer you nearly limitless utility. Due to their small form factor and customizable software control systems, fiber optic spectrometers are the ideal choice for both integration into your OEM system and for the laboratory, where you can combine modular products to form a complete solution.
-
product
Drop-In Functional Test Fixtures
Circuit Check’s drop-in base fixture and replaceable personalized plates are the ideal solution where production volumes are lower and the need to change from one fixture and test program to another occurs quickly. Interchangeable test fixture drop-ins enable the same test system to be quickly reconfigured with different tooling and probe patterns for different products. This maximizes equipment re-use, while minimizing the cost for each new test. With Circuit Check’s base fixture and drop-ins, the wiring and test electronics are not disturbed, thus ensuring configuration consistency each time the system is re-tooled.
-
product
Electric Actuator
ROMpak
The ROM range of actuators can be enhanced with the addition of a self-contained control package to create a ROMpak actuator. This adds local controls, status indication relays, isolated control circuits and support for Rotork control options such as Folomatic, Pakscan™ and other bus systems.
-
product
LXI Microwave Multiplexer, 50Ω 4-Channel 13-Bank 18GHz SMA
60-802-213
The 60-802-213 is a 4-channel, 13-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
product
Fiber Optic Accelerometer
MR660
The MR660 Series Accelerometer provides an innovative solution to measure vibration and movement in high voltage or ATEX environments. The MR660 Accelerometer system employs a highly sensitive MEMS membrane to provide a robust system capable of producing an output signal of 100mV/g pk-pk.
-
product
ISR Sensors & Advanced Area Effects
Textron Systems has more than 50 years of experience delivering smart, capable, human-in-the-loop intelligence, surveillance and reconnaissance (ISR) sensor systems and advanced area effects (AAE) munitions. These mature, proven and policy-compliant technologies defend those who defend us all. To reliably execute their missions, warfighters require continuous situational awareness and capable assets to:*Detect and identify targets*Fix and track enemy movements *Apply command-and-control capabilities to target and engage enemy vehicles based on rules of engagement *Evaluate and assess
-
product
General Purpose Amplifier
Easy to use 1.5V to 5.5V amplifiers with 69uA/ch and 150uV offsets, perfect for battery based or power concerned systems.
-
product
F9 Systems CalBlade
The CalBlade backplane calibration fixture isdesigned to permit accurate and convenient impedance and transmission measurements of a HM-Zd backplane. The CalBlade is used to calibratethe logic card connector interface to the backplane rather than to the usual far-end of the coaxial measurement cables. Very accurate impedance, skew and propagation delay measurements are possible since parasitic fixturing effects are removed.
