Showing results: 3166 - 3180 of 4410 items found.
-
Instron
During tests carried out on servohydraulic machines, elements of the system are subject to acceleration. As a result, in addition to the force applied to the specimen, the load cell also reads forces resulting from its own movement and the mass of the grips and fixtures attached to it. Dynacell is the world's first truly dynamic load cell, designed from the outset for measuring dynamic loads. Dynacell introduces the following advantages:*Reduces dynamic load errors which can be a significant percentage of reading *Increases productivity by allowing higher frequency operation while maintaining test validity *Improvements such as doubling the frequency are common
-
SMX-6XXX (RF/Switching) -
AMETEK VTI Instruments
The VTI SMX-6xxx Series of high density non-blocking RF multiplexers deliver exceptional performance and reliability in a compact single-slot configuration. Front panel connectivity is available in both SMB and PKZ formats to integrate seamlessly into new or existing test systems. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers.The SMX-6xxx Series delivers unmatched bandwidth and isolation performance resulting in exceptional measurement integrity that is ideal for the most demanding aerospace, defense and automotive automated test equipment (ATE) applications.
-
783814-01 -
NI
3 Vrms, 102.4 kS/s/ch Simultaneous, 2-Channel C Series Voltage Input Module - The NI‑9251 with mini XLR is a low-distortion input channel that allows for the high dynamic range measurements necessary to fully test and evaluate modern audio outputs used in most consumer electronic devices. Unlike sound card-based solutions, you can quickly deploy the NI‑9251 to guarantee long-term measurement repeatability and increased test system uptime. To maximize low-noise benefits, the NI‑9251 differential input is provided through a mini‑XLR connector, which delivers a truly balanced input.
-
Model 3541 -
Jinan Testing Equipment IE Corporation
The Model 3541 is designed for determination of fracture mechanics parameters such as JIC, KIC, R-curve, fatigue crack growth rate (da/dN), and testing to standards such as E1820, E399, E647, etc. These COD gages conform to the requirements of E1820 (the replacement for E813 and E1737) for JIC and R-curve determination. Special configurations are available to meet the requirements of ASTM E399 for fracture toughness (please consult the factory for these configurations). In addition, the modified groove design complies with E1820 tests where greater stability and accuracy results from the sharper groove root. Clip-on gages are used for a variety of fracture mechanics tests, including compact tension, arc shaped, disk shaped, bend specimens or other specimen geometries in compliance with ASTM and other standards organization’s test methods. Clip-on gages can be used directly on test specimens where the knife edges are integral with the test specimen or, alternately, with optional bolt-on knife edges mounted on the test specimen.The Model 3541 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
MB Dynamics Inc.
At MB Dynamics, we’re proud to provide clients in a wide range of industries with quiet, custom turnkey component testing systems for combined squeak & rattle testing as well as durability testing of different components and subsystems (in 1 to 6 DOF). Test items can be excited in one or more axes to understand and characterize the physics and root causes of BSRs. Real-world, on-road vibration conditions are multi-axis simultaneous – vertical, fore-aft or longitudinal, lateral, roll, pitch, and yaw – 6 degrees of freedom or 6 DOF. Affordability drives decisions to find BSRs by exciting in one or two – fewer than 6 DOF. That has been a driving force for MB – be effective at finding BSRs with a lesser number of shakers (DOFs) and thus reduce the test equipment cost of finding BSRs. Vertical-only can be effective; sequential vertical then fore-aft then lateral is one step closer to real-world; creating vibration in four or five axes of response simultaneously is even closer; and full 6 DOF systems that are quiet come closest to duplicating in the lab the on-road conditions. MB offers all these possibilities to meet trade-offs of budget, test time, road replication, and BSR detection effectiveness.
-
RTS65 -
Bluetest AB
Our new RTS65 reverberation chamber is designed to optimize the time you spend on OTA measurements. Our development focus has been on increasing the productivity in your lab. We want your focus to be on your results, not the test equipment. We have developed a new generation of RTS that is an integrated system which will give the user experience every engineer deserves..
-
KLA-Tencor Corp
KLA’s patterning simulation systems use advanced models to explore critical-feature designs, manufacturability and process-limited yield of proposed lithography and patterning technologies. Our patterning simulation software allows researchers to evaluate advanced patterning technologies, such as EUV lithography and multiple patterning techniques, without the time and expense of printing hundreds of test wafers using experimental materials and prototype process equipment.
-
Applied Image, Inc.
ISO has been the governing body for Image Quality Testing all over the world. To that end, APPLIED IMAGE is proud to be a participant in assuring that the industry has products that meet or exceed the requirements of ISO. Since ISO covers many levels, we provide test patterns of various types that can be used for Image Capture and Evaluation of Optical and Imaging systems of all types.
-
Amida Technology, Inc.
AMIDA ATI 600 Tester is a dedicated test system for semiconductor components (MOSFET, BJT, DIODE, ... etc.), which can accurately and quickly measure product parameters through form filling and editable program control. In practical applications, AMIDA ATI 600 Tester is the best choice for users, whether it is CP or FT mass production testing, or research projects of component characteristics.
-
DiagnoSYS Systems Ltd
The compact and portable Faultfinder VIP system, combined with a Laptop running TestVue software, provides a way to rapidly identify failures by troubleshooting a PCB or CCA. It uses impedance signatures (also known as VI testing) measured from a known working circuit and stores them as a test program. These stored signatures are then compared to the ones being measured on the suspect circuit to automatically determine if there is a fault.
-
Raytheon Company
Mobile Range™ is an integrated suite of communications, optics, and telemetry capabilities, which can be deployed anywhere in the world on land, at sea or in the air with minimal support staff or infrastructure. It enables in-country flight testing, demonstrations, and data collection in a variety of environments and conditions. The system has the ability to test anything that has an RF-transmitted data stream and can be set up and operational in as little as four hours.
-
Aero Instruments & Avionics, Inc.
The GPWS & Anti-Skid Department offers complete testing, repair, and overhaul of Sundstrand Mark I, II, III, V, and VII GPWS Computers (utilizing factory test equipment and training), Collins Flight Profile Comparators, and Bendix GPW Computers. Our latest support addition is the Honeywell Mark V and Mark VII EGPWS, ENHANCED Ground Prox Warning System.
-
TS9000 Family -
Advantest Corp.
The TS9000 series leverages Advantest's industry-leading terahertz analysis technology and expertise amassed over our decades as a global leader in semiconductor test equipment. This system provides a new high-speed, high-precision solution for measurement and analysis tasks including IC chip mold thickness and IC package / printed board wiring quality, which existing methods cannot measure adequately.
-
TD4000A -
Ponovo Power Co., Ltd.
TD series testing equipment is a HVDC Test Set consisting of control unit and DC high current output unit. And the TD series HVDC primary injection system includes 3 types, which could output 2000Adc/4000Adc/ 8000Adc and 0.1% high accuracy, suitable to be used for different HVDC testing requirements, such as in HVDC Converting station, or railway transportation line, etc.
-
FIT448 -
Matco Tools
This set includes everything to test the following: Bosch AFC, MPC, Digijet/Digifant- (except CIS- use our FIT447) Chrysler Corporation Ford Motor Company General Motors (except TBI- use our FIT446) Japanese Fuel Injection Systems Others using Bendi. The 2-1/2" gauge has a dual scale dial with ranges from 0-100psi and 0-7 bar.
