Showing results: 1 - 15 of 75 items found.
-
1945 -
Peaceful Thriving Enterprise Co Ltd
This is a portable 220VAC socket tester to inspect the wiring conditions. The tester also features current variation for simulation of different leaking current. With the current variation, technician is able to test the condition of Ground Fault Circuit Interrupter (GFCI) / Residual Current Device (RCD) easily.
-
ST120+ -
Fluke Corporation
The Fluke ST120+ GFCI Socket Tester with Beeper checks that each wire in the outlet is properly connected to the building's electrical system. Via the bright LEDs and included chart, you can quickly and easily verify the wiring of an outlet. Able to identify several common wiring errors, including reversed phase and neutral wires and an open ground, the ST120+ will give you confidence on your next job.
-
-
MEET International Ltd.
*Power supply from mains : 200-230V AC*Transmit AC signal through concrete walls; Shielded / armored cable*Internal fuse protection
-
K-281 -
The Eastern Specialty Company
Knopp’s K-281 Polyphase Socket Tester is designed to detect backfeed conditions, grounds, short circuits and wiring errors in either a 120/240, 120/208 or 277/480 volt meter socket. It is equipped with high intensity Power Lights and Fault Lights to show whether or not the meter is safe to set. The Polyphase Socket Tester also comes with a heavy duty handle for quick and easy installation.
-
RV 7 -
Square Wheel Industries, Inc.
Blade Socket Tester offers a fast, easy way to isolate a lighting problem to the trailer or towing vehicle. A must have for anyone who deals with hitch and lighting hookup installations, it tests the output of towing vehicle's RV 7-blade lighting socket.
-
TEL5 -
Standard Electric Works Co., Ltd
● Fast, easy wiring check.● Easy to read light indication.● Confirm the correct wiring of AC socket.● Test GFCI for correct wiring & operation.● Detect 5 wiring faults.● GFCI circuit trips to confirm the tester is working.● The testing current for GFCI is about 8mA.
-
ST120 -
Fluke Corporation
The Fluke ST120 GFCI Socket Tester checks that each wire in the outlet is properly connected to the building's electrical system. Via the bright LEDs and included chart, you can quickly and easily verify the wiring of an outlet. Able to identify several common wiring errors, including reversed phase and neutral wires and an open ground, the ST120 will give you confidence on your next job.
-
Testboy GmbH
Using the new Testavit Schuki 1 LCD and 3 LCD, specialists easily check to see if sockets, cable drums or connecting cables are correctly connected in 230 V installations. Due to three LEDs, the connection status can be quickly and clearly determined. In addition, through the finger contact, it can be tested to see whether an impermissible, high contact voltage is applied at the protective earth connection. In addition, using the Testavit Schuki 1 LCD, a 30 mA FI circuit breaker (RCD) can be triggered via a pushbutton.
-
MDPPTSTUSB -
Matco Tools
*Provides the user with a simple way to test a USB socket on a vehicle*Mini probe will light up when 4.4V - 5.25V is detected
-
PCCtest 460 -
Sycard Technology
The PCCtest 460 is designed to test the full functionality of the PC Card/CardBus interface. Since the 1995 and subsequent releases of the PC Card Standard, the number of different cards that can be supported in a single machine has drastically increased. It is not uncommon for a PC Card slot to support 32-bit CardBus, 16-bit PC Card, Zoomed Video, 5V and 3.3V cards.
-
-
CF test 222 -
Sycard Technology
The CF test 222 socket tester provides a quick and easy way of verifying the operation of a CompactFlash™ host socket. Housed in a standard 3.3mm CompactFlash™ card, the CF test is fully self-contained. The CF test socket tester verifies all signals on the CompactFlash™ interface including accurate Vcc measurements.
-
CF test 220 -
Sycard Technology
The CF test 220 socket tester provides a quick and easy way of verifying the operation of a CompactFlash™ host socket. Housed in a standard 3.3mm CompactFlash™ card, the CF test is fully self-contained. The CF test socket tester verifies all signals on the CompactFlash™ interface including accurate Vcc measurements.
-
Non-Contact & Socket -
Amprobe Test Tools
Use Amprobe non-contact volt probes to safely check circuit breakers, wall sockets and fuses for voltage presence with portable, economical tools. For sockets, choose an Amprobe socket tester, which can confirm whether GFCI breakers are properly wired.