Showing results: 46 - 60 of 191 items found.
-
Seitron
Radio receiver for heating / cooling systems equipped with an integrated antenna, an output with SPDT relay and an RS485 Modbus® RTU slave communication port.
-
ifm efector, inc.
*Monitoring of up to 31 safe AS-i slaves*Applications: door monitoring, light curtains, e-stop, two-hand control*Safe AS-i modules for field applications and control cabinets*Safe AS-i door switches with guard locking and guard lock monitoring
-
EPS-1132 -
ADLINK Technology Inc.
*32-CH sinking type digital input*Quick removable European type connector*Slave module healthy monitoring*Wide operation temperature range: -20°C - 60°C*Compact size: 100 (L) x 100 (H) mm
-
A3818 -
CAEN S.p.A.
The Mod. A3818(*) is a PCI Express x8 card that can plug into both x8 and x16 PC PCI Express slot (V2.0), which allows the control of up to 4 CONET2 independent networks (each network can be made of up to 8 CONET2 slaves).
-
VME-1128 -
Abaco Systems Inc
VME-1128 is a 128-bit High-Voltage Digital Input Board with Built-in-Test. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297) with the following mnemonics: A24:A16:D32/D16/D08 (EO): Slave: 39/3D:29/2D Form factor: 6U
-
WSMBT -
Witte Software
WSMBT is a powerful and simple to use .Net component that makes it easy to access data from a Modbus slave device connected to the PC's Ethernet network. Simply drop the component on your form and talk to your device with your VB.NET, C# or Managed C++.
-
RFFE -
Arasan Chip Systems, Inc.
Mobile phone radios have developed into highly complex, multi-band and multi-standard designs that often have multiple radio frequency (RF) signal chains. The MIPI Alliance Specification for RF Front-End Control Interface (RFFE) was developed to offer a common and widespread method for controlling RF front-end devices. The RFFE Master IP core typically resides in the RFIC in a mobile platform, and utilizes the RFFE bus to identify, program and monitor the registers in RF front end Slave devices through programmed IO. It is designed to support existing standards such as LTE, UMTS, HSPA and EGPRS, and is usable in configurations ranging from single Master/single Slave to multi-Master/multi-Slave.
-
HSL-DI32-DB-N -
ADLINK Technology Inc.
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type sensor inputs or dry contact*Photo couple isolation voltage: 2500Vrms*Input impedance: 4.7KΩ*Input current: ??10mA (Max), ??12.5mA (Peak)*Input voltage: ??40V (Max)
-
XMC-FPD-xxx -
ALPHI Technology Corporation
XMC Bus VITA 42• 3.3V I/O, 5V tolerant businterfaces• Local Bus Clock rates at66MHz• Compliant PCIeSpecification, r1.0a x1• Direct slave data transfers• DMA Capability• Up to 160Mb/s Transfer• DMA Transfer per Fifo Level
-
VME-1129 -
Abaco Systems Inc
VME-1129 128-bit high voltage digital input board with Built-in-Test and input filter. This product complies with the VMEbus specification (ANSI/IEEE STD 1014-1987, IEC 821 and 297), with the following mnemonics: A24:A16: D32/D16/D08 (EO): Slave:39/3D: 29/2D Form Factor: 6U
-
DV164122 -
Microchip Technology Inc.
The PICkit Serial Analyzer is a low-cost USB-based tool used to direct communication between a PC and an external serial device. I2C™ - Master, I2C™ - Slave, SPI - Master, USART – Asynchronous, USART – Synchronous, LIN (external hardware required to meet electrical specifications), MICROWIRE.
-
ET9400 -
EtherCAT Technology Group
The Conformance Test Tool (CTT) enables in-house testing of EtherCAT slave devices. The use of the CTT supports EtherCAT device development, helps to ensure conformance prior to device release and to prepare the device for the official, independent Conformance Test in an EtherCAT Test Center (ETC) accredited by the EtherCAT Technology Group.
-
52400 series -
Chroma ATE Inc.
Hybrid Compatible PXIFour quadrant operationHigh source/measurement resolution (multiple ranges)Low output noiseHigh programming/measurement speed (100k s/S) & slew rateOptional measurement logDIO bitsOutput profiling by hardware sequencerProgrammable output resistanceFloating & Guarding output16 Control Bandwidth SelectionMaster / Slave operationDriver with LabView/LabWindows & C/C# APISoftpanel GUI
-
ams AG
A companion IC for battery- and current sensor LIN slaves. The integrated chop clock synchronization enables a zero offset measurement system for small shunt signals in positive battery rail in conjunction with AS8510.
-
CPCI-DA8-2 -
ALPHI Technology Corporation
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system.