Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
product
FMC, XMC & PMC
The FPGA Mezzanine Card is used by Data Patterns to implement signal interface with external world compatible FPGAs mounted on the FMC carrier there are primarily used for high speed analog interface for digitization (ADCs) and waveform generation (DACs). This form factor is also utilized for special I/O Interfaces such as various avionic protocols and buses. FMC I/O signals may be routed via front panel connectors or through Mezzanine connectors that route the signal back to the carrier board for routing through rear I/O of the Chassis. The system interface is designed for routing to FPGAs using a VITA 57 0.05 Pitch Terminal Array Assembly.
-
product
Stackable And Configurable Signal Generator For CAN Applications.
K- Volt
The K-Volt can be used to generate fast configurable analog and digital signals from CAN messages. Designed for high speed and accurate simulation of sensors (For example HIL and Replay systems). The K-Volt can be connected directly to a PC via a USB connection.
-
product
FieldFox Handheld Microwave Spectrum Analyzer, 26.5 GHz
N9938A
100 kHz to 26.5 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
product
VXI Synchro/Resolver Module
VX3701
With so-called synchro/resolver cards, rotation angle sensors that work according to the synchro/resolver principle can be measured. Depending on the angle of rotation, these generate a sine and cosine signal, in order to determine the position and direction of rotation.
-
product
Signal, Patchcord, ITA, 36", TriPaddle, 24 AWG Twisted Pair White/Black, Single Ended (3 Amps)
7-103424000-036
Signal, Patchcord, ITA, 36", TriPaddle, 24 AWG Twisted Pair White/Black, Single Ended (3 Amps).
-
product
In-Line Signal Conditioner
500
Small, DC powered in-line signal conditioner with 9-pin connectors, +/-5V and 4-20mA outputs and 1000Hz bandwidth.
-
product
Mixed Signal Oscilloscope - 350 MHz, 4 Analog Plus 16 Digital Channels
MSOX3034T
350 MHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
product
1211a Optical Receiver/Distribution
Precise Time and Frequency, Inc.
To complement the range of high quality frequency and timing references, Precise Time and Frequency, LLC. has now introduced a new Optical Time Code Receiver, with Auto Switching, a full complement of time code outputs, and Ethernet/RS232 remote monitoring/control interface.In addition to the auto switching capability, the new ptf 1211A delivers up to thirty six channels of Time Code outputs, including re-transmission of the optical input. The unit can accept a pair of inputs (usually from separ...show more -
product
Fast Tuned Notch Filter
ES005 & ES006
Teledyne Defence & Space’s (TDS) range of Fast Tuned Notch Filters (FTNF) have been designed to protect Electronic Support Measures (ESM) receivers from high duty cycle, frequency agile interference produced by on board (or cohort) combat radar systems. ESM sensors often need protection from high power nearby radars, and such signals can reduce receiver dynamic range.
-
product
Signal, Patchcord, Receiver, 72", TriPaddle, 22 AWG, Single Ended ( 5 Amps)
7-104922000-072
Signal, Patchcord, Receiver, 72", TriPaddle, 22 AWG, Single Ended ( 5 Amps).
-
product
Amplifiers
Amplifiers are used to amplify the energy output of photodetectors as well as convert their electrical signal for a number of illumination measurement or spectroscopy applications. Amplifiers are digital systems that amplify the low electrical current transmitted by photodetectors to easily detectable levels. Amplifiers also convert photodetectors' electrical current into voltage so that their signal may be read by other digital devices. Amplifiers are indispensable for nearly any light measurement applications by greatly increasing the usability of a detector system.
-
product
Performance Board
The role of the performance board is accurate transmission of tester signals all the way to the device leads. Custom performance boards from ADVANTEST deliver support for DUTs (devices under test), as they become faster and smaller, with greater pin counts, and increasingly take the form of SMDs. ADVANTEST performance boards also support a host of test requirements, such as analog test, high-speed performance, and high-density, for testing state-of-the-art ICs.
-
product
Multi Function Automobile Tester
6522
Peaceful Thriving Enterprise Co Ltd
The multi-function automobile tester has LCD display to indicate the measured result. It has polarity detection with the LEDs for a positive and negative indication of DC voltage. For auto use, the functions included the measurement of DC voltage and current, signal frequency and max/min voltage, resistance, temperature and power providing testing.
-
product
The Nortech Fiber Optic Monitors
The fiber optic signal conditioners are designed for direct, accurate and real-time temperature monitoring to manage and maximize your transformer’s performance. The Nortech temperature monitor family comes in three different classes: the EasyGrid is the most comprehensive model, the EasyGrid LT is a compact and very cost-effective model for low channel count monitoring applications, and the EasyGrid Base is and even more compact model designed for easy network integration.
-
product
PXI/PXIe LVDT/RVDT Simulator Module, 4-Banks
43-670-101-AABBCC
The 41/43-670-101 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has four banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal.
-
product
Oscilloscope Probe
Oscilloscope Probes can conduct signals up to 2.5 GHz, 300 V, or 500 Arms, even in extreme environments. They offer fixed attenuation of 10X or 100X or switchable attenuation between 1X and 10X. Oscilloscope Probes are offered in several types, including single-ended and differential, active and passive, voltage and current.
-
product
Signal Generators
2, 4 and 8 Channel Arbitrary Waveform Generator and Pulse Pattern Generator solutions are ideal choice in automated test benches, for physics experiments, semiconductor tests, analog and digital debugging.
-
product
Rolling Seal 8 Optical Connector - APC (RS8 APC)
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
product
PXIe 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels
M4X.4470-X4
The M4x.44xx-x4 series digitizers deliver the highest performance in both speed and resolution. The series includes PCIe cards with either two or four synchronous channels where each channel has its own dedicated ADC. The ADC’s can sample at rates from 130 MS/s up to 500 MS/s and are available with either 14 bit or 16 bit resolution. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high quality signal acquisition.
-
product
LXI Microwave Multiplexer, SP6T, 14-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-514
Our 60-800-514 is a 14 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Mixed Signal Oscilloscope 200 MHz, 2 Analog Plus 16 Digital Channels
MSOX3022G
The MSOX3022G 200 MHz oscilloscope provides 2 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
product
Signal Conditioning Modules
Signal conditioning modules provide signal conditioning on a per-module basis for various types of sensor or signal.
-
product
Single Fiber Bi-Direction EDFA
HA8000
Hangzhou Huatai Optic Tech. Co., Ltd.
HA8000 series, is a bi-directional fiber amplifier with high-quality. It can transmit and amplify downlink and uplink signal on one fiber. It offers an economical solution to network operators when utilizing the existing fiber source, upgrading networks and providing bi-directional VAD business.
-
product
PXI 2 Amp MUX, Dual 32-Channel 1-Pole
40-635-005
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC. The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
PXIe Vector Signal Generator: 1 MHz to 3 GHz or 6 GHz
M9381A
Choose your RF modulation bandwidth, 40, 100, or 160 MHz, and easily upgrade as test needs change Increase throughput with fastest RF frequency tuning and amplitude switching for high-speed automated test Save space with a compact solution for up to 8x8 MIMO with phase coherence Get up and running quickly with validated application-specific reference solutions Simplify signal creation with Keysight's Signal Studio and Waveform Creator
-
product
PXI/PXIe Microwave Multiplexer, Single SP6T, 67 GHz, 50 Ω, SMA-1.85, Terminated, Failsafe
42-785C-571-T
The 40-785C-571-T (PXI) and 42-785C-571-T (PXIe) are single failsafe SP6T 67 GHz with automatic termination of unused signals. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
Bar Indicators
Orbit Controls bar displays are flush-mounted display devices with one or two three-color bars. They can also be ordered with a digital display. The devices are designed for connection to various process signals and can be equipped with control outputs.
-
product
PCI Very High Density Multiplexer, 198-Channel, 1-Pole
50-670C-022-198/1
The 50-670C-022-198/1 is a 198-channel, 1-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
product
Gasoline Engine Tachometer
SE-1620
The SE-1620 is an engine tachometer that performs measurement of the number of revolutions of a gasoline engine by connecting an engine revolution sensor such as an ignition pulse detector. A 100-mm wide-angle meter is used for the display, and both analog output and pulse output functions are provided as standard.Simply attach an ignition pulse detector or one of our other compatible detectors to the engine to enable measurement of the number of revolutions of a gasoline engine. The inputs, outputs and input power supply are all isolated to ensure the output of analog and pulse signals with superior noise resistance and stability characteristics.
-
product
Power Dividers
Powers plitters can divide one signal into two or N way equal or non-equal energy, in reverse,they are also used as combiners by combining multiple signal into one. They are mainly used in feed network in antenna array, mixer and balanced amplifier, finish the work of distributing, combining and measuring power, isolating signal sources and measuring swept reflected coefficient etc.
