Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
product
PXI Triple 2 Channel Fibre Optic MU
40-855-332
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
3U CompactPCI 8-port Serial Communication Module
cPCI-3548
- Supports 32-bit/33MHz CompactPCI bus- 16C550A compatible serial communication controller- Eight RS-232/422/485 asynchronous communications ports with intelligent buffer- 2500 VDC signal to ground isolation voltage- Auto-flow control; change mode by dip switch- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS, shared IRQ- Surge protectors; rugged DB-62 connector
-
product
LXI Microwave Multiplexer, SP6T, 4-Bank, 50GHz, 50Ω, SMA-2.4
60-800-604
Our 60-800-604 is a 4 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Optical signal transmission
Bus systems
Allows for the transmission of high speed CAN signals via optical fibre cables during EMC tests or when there are great potential differences (high voltage).
-
product
LXI Microwave Multiplexer, SP6T, 5-Bank, 67GHz, 50Ω, SMA-1.85
60-800-805
Our 60-800-805 is a 5 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
Waveform Monitors
LV5600
The LV5600 is a hybrid-type waveform monitor compatible with 4K/HD/SD SDI signal and IP signal.
-
product
Quad Core KeyStone™ DSP + UltraScale™ FPGA Module
SMT6657-KU35
Sundance Multiprocessor Technology Ltd.
The SMT6657 DSP+FPGA module is a reliable and flexible platform for digital signal processing applications requiring high-performance integer and floating-point computation.It is applicable to both symmetric multiprocessing applications in which the computational load is shared by the two DSPs and asymmetric applications where one of the DSPs is responsible for hard real-time processing and the other acts as a supervisor, handling all non-deterministic communication and optionally running under control of an operating system.
-
product
Buffers
Silicon Labs' clock buffers provide ultra-low additive jitter, low skew clock distribution. In addition to differential and LVCMOS buffers, Silicon Labs offers universal clock buffers that support any-in/out signal format and integrate clock muxing and division to further simplify clock tree design.
-
product
PXIe Microwave Multiplexer, Single SP6T, 26.5 GHz, 50 Ω, SMA, Terminated, Failsafe
42-785C-531-T
The 40-785C-531-T (PXI) and 42-785C-531-T (PXIe) are single failsafe SP6T 26.5 GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
product
VME Bus Tester
VBT100
The VBT100 has been designed to withstand and measure excessive voltages on both signal and power supply pins. This capability allows it to operate in faulty backplanes that could damage other boards. The tester also detects, measures and identifies which signals have excessive voltages so they can be repaired before boards are loaded into a backplane.
-
product
Dual LGA 4189 Intel® Xeon® Scalable Proprietary Server Board with 16 DDR4, 4 PCIe x16, 3 PCIe x8, 1 PCIe x4, 4 SATA3, 4 USB3.0, IPMI
Part No. ASMB-622
- Proprietary server board with dual Xeon® Scalable processors- DDR4 3200MHz RDIMM up to 1TB, support Intel Optane Persistent Memory- 1 SFF-8643 connector support 4 ports SATA drive, 1 M.2 2280 on board- 1 SlimSAS connector support 2 ports NVMe drive in option- Four PCIe x16 slots (Gen4) supporting 2 double deck cards with active FAN- Four PCIe X8 slots support 3 PCIeX8 and 1 PCIeX4 signals- Quad LAN with Intel I350- Flexible IO board design
-
product
7 Round Pin Tractor Trailer Circuit Checker / Maintenance Kit
#8029
Innovative Products of America
Test, clean and restore 7 round pin connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 7 round connectors. Tests tractor electrical circuits Removes corrosion from truck and trailer connectors Enhances electrical contact points Extends harness life Use as a pin wear gaugePatentedKit Includes: #7865L: 7 Round Pin Tractor Trailer Circuit Checker, #8024: 7 Round Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
product
USRP-2955, 10 MHz to 6 GHz, 80 MHz Bandwidth, GPS-Disciplined OCXO, Reconfigurable USRP Software Defined Radio Device
785264-01
The USRP-2955 provides an integrated hardware and software solution for rapidly prototyping high-performance wireless receiver systems. It is designed for over-the-air signal acquisition and analysis. It features a two-stage superheterodyne architecture with four independent receiver channels and shares local oscillators for phase-coherent operation. It also offers a Kintex-7 FPGA programmable with the LabVIEW FPGA Module. With these features, the USRP-2955 has the RF and processing performance ...show more -
product
WaveLink Temperature Extension cables for Dx20
Dx20-HiTemp
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
product
Signal Architect Simulator Software
GNSS
The GNSS Signal Architect Simulator Software is ideal for applications requiring: High fidelity simulation of GNSS signals Digital data analysis of GNSS signal effects RF signal generation through digital playback Highly repetitive testing where consistency between test runs is critical Easy to use Graphical User Interface Low initial and support costs
-
product
Multi-Channel Phase Comparator
VCH-315M
Multi-channel phase comparator VCH-315M, together with a computer and special software, is designed for simultaneous measurement of frequency instability characteristics (RMS, RMS) of a group of sinusoidal signals of standard frequencies 5; ten; 100 MHz.
-
product
PXI-8511, 1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module
780686-02
1‑ or 2-Port, Low-Speed/Fault Tolerant PXI CAN Interface Module—The PXI‑8511 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The PXI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
product
Single 24x4 1-Pole High-Density PXI Matrix Module
40-520-402
The 40-520 family of high-density PXI matrices is available in 22 different configurations with up to 256 crosspoints. The choice of six bus widths (x16, x12, x8, x6, x4 and x2) enables competitively priced solutions using Pickering Electronics instrumentation quality reed relays. These relays offer very long life with good low-level switching performance and excellent contact resistance stability. Typical applications include signal routing in ATE and data acquisition systems.
-
product
High Power RF-Signal Generators
Becker Nachrichtentechnik GmbH
Multi channel RF signal sources with precise high power output levels. Each output offers a separate, analogue level control. This ensures highest precision in level during a long term usage.
-
product
Power Switches
SMX-2002 (Power)
The SMX-2002 is the only switch module in its class with the ability to switch up to 16A. Some applications include: AC line power switching, switching of DC or AC power supplies, control or driving relays for industrial machines (robotics, numerical control machines), automotive engine control, and solenoid switching. Since this module typically switches power to the UUT or interface, the SMX-2002 includes failsafe pins on the front panel which can be configured to open all relays when a failsafe signal is activated. This approach can instantly removes all power to the UUT or interface.
-
product
PXIe-5451, 145 MHz, 16-Bit, 2 GB PXI Waveform Generator
781204-03
PXIe, 145 MHz, 16-Bit, 2 GB PXI Waveform Generator—The PXIe‑5451 is a 145 MHz, dual‐channel arbitrary waveform generator capable of generating user-definied waveforms, standard functions, and I/Q communications signals. It is an ideal instrument for including in systems for testing devices with I/Q inputs, or as the baseband component of an RF vector signal generator as wells as time-domain signals like envelope tracking. The PXIe‑5451 also features onboard signal processing (OSP) functions that...show more -
product
PXI High Density Matrix Module, 32x4, 1-Pole, 2A, 60W
40-528B-001
PThe 40-528B is a 128 crosspoint PXI matrix with single pole switching and a configuration of 32x4 using electromechanical relays with 2 A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems.
-
product
Signal, Patchcord, ITA, 72", QuadraPaddle, 22 AWG White Twisted Pair, Single Ended ( 5 Amps)
7-121422000-072
Signal, Patchcord, ITA, 72", QuadraPaddle, 22 AWG White Twisted Pair, Single Ended ( 5 Amps).
-
product
Two-wavelength SM WDMs
Wavelength Division Multiplexers (WDMs) are used to combine or split two different single mode signals with low insertion loss. Thorlabs' WDMs featured on this page are manufactured using Fused Biconic Taper (FBT) technology and are designed for common NIR and telecom wavelengths (see the table to the right for options). They are an ideal solution for combining pump and signal wavelengths in fiber lasers and amplifiers or for combining telecom signals. Our WDMs have undergone extensive testing to ensure they meet or surpass Telcordia requirements; please see the Reliability Testing tab for details.
-
product
AC Calibration Standard
1U647-001
The 1U647-001 is a low cost calibration standard used to determine if a 1U632-100 or a 1U663-100 DMU requires factory calibration. Its portability makes it ideal for field-testing. The standard generates signals that simulate the aircraft’s resolvers, rotary variable transformers (RVTs), and linear variable displacement transformers (LVDTs). The unit also generates a pulse width modulated (PWM) signal, and routes the output of an ARINC 429 source to the different DMU input channels. The calibration standard connects directly to the DMU and replaces the output signals of an active extender card. Discrete switch settings simplify testing. The unit is housed in a rugged aluminum case.
-
product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
783127-02
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
product
PXI Transfer Switch Module
PXI Transfer Switch Modules offer fast insertion times and low insertion loss to switch loads at RF frequencies. The modules also have 50 impedance that helps minimize reflections of the RF signal and protect your instruments. You can program the PXI Transfer Switch Module using the NI-SWITCH instrument driver.
-
product
BCD to Binary Converter
BCD250
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
product
Digital Psophometer
Model 1072
Aplab Psophometer is a portable unit designed for the use of testing telecommunication equipment. It has Psophometric filter, which has the frequency response of the weighing network based on the CCITT recommendations and frequency response characteristics for unweighted measurements. The additional features included in this model are, ‘Recorder out’ available at the rear panel for plotting a response curve, built-in stable calibration signal for calibration check and Lo Battery facility to check the Battery condition.
-
product
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG Twisted Pair Shielded, White/White-Blue, Single Ended
7-121425000-036
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG Twisted Pair Shielded, White/White-Blue, Single Ended.
