Signal
detectable impulse of electromagnetic radiation or quantum state superposed.
See Also: Signal Sources, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners, Fidelity, Hunting
-
product
PXI/PXIe High Density 2A Multiplexer, 8-Bank, 4-Channel, 4-Pole
42-614D-005
The 40-614D-005 (PXI) and 42-614D-005 (PXIe) 8-bank, 4-channel, 4-pole multiplexers are part of the High Density 2A multiplexer module range available in 23 configurations (see 'Also in this Range' link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
LXI 50Ω 6:1 Microwave Multiplexer 16-bank 40GHz SMA
60-800-416
Our 60-800 Microwave Multiplexer range is suitable for switching 50 ohm signals up to 40GHz. With the capability of supporting up to 16 banks of 6 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA connectors.
-
product
CC15010X, 10 MHz, 150 A Current Oscilloscope Probe
786849-01
The CC15010X, or Hioki 3274, is a clamp-on current probe that offers a wide DC to 10 MHz bandwidth and 150 A of continuous input. It is ideal for capturing transient current signals from switching power supplies, inverters, and motor controllers. The probe requires an external power supply.
-
product
PXI-6251, 16 AI (16-Bit, 1.25 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
779117-01
The PXI-6251 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and analog and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
product
ICD 3 Test Interface Module
AC164113
The Test Interface Board is an aid to isolate application interfacing problems when using the MPLAB ICD 3 (DV164035) as a debugger or programmer. Using the Test Interface Board and running confidence-test options under MPLAB IDE allows testing of the basic functions and signals of an MPLAB ICD 3. The diagnostic results under MPLAB IDE let the user know when the MPLAB ICD 3 is fully functional or if there is a malfunction. The MPLAB Online Help shows the user how to determine possible causes of hardware communication failures with the application.
-
product
Load Cell DIN Rail Signal Amplifier
LCD20
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
product
DDR4 BGA Interposers, DDR4 DRAM X4/x8 Packages
N2114A
The N2114A DDR4 BGA interposers provide signal access to the clock, strobe, data, address and command signals to the DDR4 BGA package for making electrical and timing measurements with an Infiniium oscilloscope. With the DDR4 JEDEC specification defined at the DRAM ballout, the BGA probe adapter provides direct signal access to BGA package for true compliance testing.
-
product
Car-to-X Signal Strength Emulator
Qosmotec Software Solutions GmbH
QPER-C2X is a special adaptation of the signal strength emulator QPER, designed for mobile and Vehicular Ad-hoc Networks (MANet and VANet). Every radio devices in such an infrastructure-less network acts as a sender, receiver, and forwarder (router). Therefore, the ports of the QPER-C2X hardware are fully connected with each other by dynamically controllable attenuators. The system is fully designed for frequencies up to 6 GHz, since wireless communication for Intelligent Transport Systems (ITS)...show more -
product
Signal, Contact, Receiver, TriPaddle, 10 Amp, 14-18 AWG
610110177
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 10 Amps Max. Continuous (14 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.41
-
product
Network Analyzers
A network analyzer is an instrument used to analyze the properties of electrical networks, especially those properties associated with the reflection and transmission of electrical signals known as scattering parameters (S-parameters). Network analyzers are used mostly at high frequencies; operating frequencies can range from 9 kHz to 110 GHz
-
product
Video Signal Generator
MSPG-4600MT
MSPG-4600MT is basically supporting the Teletext and Closed Caption as multi broadcast for the D-TV (NTSC, PAL), as well as V-Chip (Violence Chip) function to block the violence and sex etc. bad program to protect a person under age through the regulation grade.
-
product
Modern Prepolarized Precision Condenser Microphones & Preamplifiers
Modern prepolarized microphones are designed with newer technology than traditional externally polarized microphones. Prepolarized microphones have many advantages over the externally polarized models. They use ICP® power circuitry invented for sensors by PCB®. By applying a polymer coating to the top of the backplate and embedding a charge on it, expensive 200V power supplies can be eliminated and 2-20 mA constant current supplies or signal conditioners can be used as the power source.
-
product
Current Shunt Module
CURS100
The CURS100 converts a current signal output by a sensor or output device (e.g., 4 to 20 mA) to a voltage that can be measured by a datalogger. The 100 ohm resistor used for the current shunt allows currents up to 25 mA to be read on a 2500 mV range (CR10, CR10X, CR510, CR500) and currents up to 50 mA to be read on a 5000 mV range (CR23X, 21X, CR7, CR5000, CR9000, CR9000X).
-
product
Goniophotometer for Traffic Signal Lamps
LSG-1950S
LSG-1950S is a high automatic test system for luminous intensity distribution of luminaires and can be applied to quality evaluation and quality control for signal luminaires, luminaires for cars, motors, vessels and Retro-reflectors. LSG-1950S system is a goniophotometer which can measure all kinds of lamps and luminaires.• Rotations of test samples around both vertical axis (-90°~+90°) and horizontal axis (-35°~+35°) • Accuracy of angle: 0.1° • Resolution of angle: 0.01° • Photometer detector: CIE class A (standard class) accuracy • All software control, high intellectual faculties and simple operation
-
product
Signal Generators
Dongguan Longwei Electronic Technology Co., Ltd.
An electronic device that generates repeating or non-repeating waveforms used to test and evaluate electronic test equipment.
-
product
Injection Transformer
J2100A
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
product
Signal Generator, 20MHz, 1 Channel, Arb.
33511B
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
product
Signal Converters For High-accuracy Angular Measurement
EIB 1500 series
*Interpolation and digitizing electronics for the real-time digital processing of positions from two scanning heads*Input: incremental rotatory HEIDENHAIN encoder with two scanning heads and distance-coded reference marks (relative orientation of scanning heads: 180° ± 5°)*Output: EnDat 2.2, Fanuc Serial Interface, Mitsubishi high speed serial interface*Integrated subdivision: 16 384-fold
-
product
Signal, Patchcord, ITA, 36", TriPaddle, 24 AWG White Teflon, Single Ended (3 Amps)
7-103924000-036
Signal, Patchcord, ITA, 36", TriPaddle, 24 AWG White Teflon, Single Ended (3 Amps).
-
product
ICE 4000 Series
ICE4003
The ICE4003 is a dual channel filter that provides two independent UHF TX/RX channels in a single package. Each channel can operate autonomously into a dedicated antenna or both channels can be combined into a single antenna. Furthermore, the combiner used in the ICE4003 is capable of combining any combination of TX/RX signals while minimizing path loss. Currently, supported radios include the ARC-225 and ARC-210. The ICE4003 is designed with a flexible interface to support future radio requirem...show more -
product
4-Pin Trailer Light Tester
3536C
Peaceful Thriving Enterprise Co Ltd
4-pin Small Size Trailer Light Tester & Circuit Troubleshooter for US, Plug tester into vehicles 4-pin connector and operate vehicle's turn signals, lights and brakes. When there is power present, the green light will glow.
-
product
Digital Down-Conversion Firmware
FW2DDC
FW2DDC equips ADQ7WB and ADQ7DC with real-time functions commonly used in radio frequency (RF) receivers. It also contains the proprietary ADX technology which corrects mismatch errors in time-interleaved analog-to-digital converters (TI-ADCs) and thereby ensure industry-leading spurious-free dynamic range (SFDR). The digital signal processing also helps reduce the data rate to a manageable level in order to simplify data post-processing and storage.
-
product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
product
Cable and Pipe Locator
PT-14
The locator PT-14 is used as an induction signal receiver in a cable tracing and fault location set for the following applications:• tracing – finding the route and determining the burial depth of underground cables and other hidden utilities;• fault location – pinpointing interphase and phase-to-sheath short circuits faults;• cable identification – identifying a correct cable from a bunch.
-
product
102-Channel Portable Logic Analyzer
16863A
102 channels, 350 MHz state, 12.5 GHz timing zoom, 2.5 GHz timing, 2 Mb depth standard15-inch (38.1 cm) color, touch-screen display for viewing and quickly navigating large numbers of signals and buses Built-in removable SSD drive, USB 3.0 ports and LAN for fast data transfer and storage of large amounts of data1.4 GHz trigger sequencer to ensure high-speed events are captured
-
product
Signal Processors
Designed to handle frequencies ranging from 20Hz to 20KHz. This cutting-edge unit is specifically crafted for a wide array of applications, including room resonance reduction, anti-feedback control, special effects creation, and room equalization.
-
product
PXIe-5172 PXI Oscilloscope, 100 MHz, 14 bits, 250 MS/s, 8 Channels, 1.5 GB, FPGA: Kintex-7 325T
784225-01
PXIe, 100 MHz, 4- or 8-Channel, 14-Bit, Kintex-7 325T or 410T FPGA Reconfigurable PXI Oscilloscope—The PXIe 5172 high-density PXI oscilloscope has eight simultaneously-sampled channels with flexible settings for coupling and voltage range. PXI oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with many channels that require up to 250 MS/s or 100 MHz of a...show more -
product
Opto Serial Module
DS-MPE-SER4OPT
The DS-MPE-SER4OPT offers 4 RS-232/RS-485 opto-isolated serial ports in a PCIe MiniCard form factor. Each port offers 16C550 compatibility and ultra-deep 256-byte TX/RX FIFOs. Maximum data rates are 1Mbps in RS-232 mode and 10Mbps in RS-485 mode. The board is available preconfigured for 4 RS-232 ports, 4 RS-485 ports, or a combination of 2 RS-232 and 2 RS-485 ports. I/O signals are provided on two miniature latching connectors, with 2 ports per connector.
-
product
VXI IP Carrier Module
DP-VXI-5124
The Data Patterns DP-VXI-5124 is a VXI 'C' size Carrier Board, which occupies a single slot in the VXI system. The module is a register based device with A16/A24/A32 address space and has interrupter capability. The carrier board's VXI bus interface is used to program and monitor the carrier board registers for configuration and control of the board. The VXI bus interface is also used to communicate with and control the external devices that are connected to an IP modules field I/O signals.
-
product
Engineering Support Platform
ESP
ESP, or Engineering Support Platform, is a low cost, powerful and versatile platform for the development, deployment and support of FPGA Applications. ESP is powered by DSX core, ARC’s core element for the development and deployment of digital and mixed signal systems. The standard system contains 2 custom FPGA system, often configured in combination where one acts as the application firmware, and the other is used for test. But the system is expandable and configurable in any combination to sol...show more
