Showing results: 106 - 120 of 224 items found.
-
H364 Series -
Howell Instruments, Inc.
Enables users to input enginespecific phase angle table and torque shaft values into the unit software program for quick and easy operation on the flight line • Contains embedded software that allows simple 0% and 100% phase simulation
-
RS425 -
Datum Electronics, Ltd.
These contactless Torque Transducers are not limited by operational speeds, can fit any shaft and capable of measuring torque from 1nm and up to 500knm, providing highly accurate and reliable torque measurement in many applications.
-
ENC-SIM01 -
Plant Control and Automation Pty Ltd
This instrument is designed to simulate the function of most types of incremental encoders; it allows the engineer to fully test a control system that uses a rotary or linear shaft encoder, without the need for any mechanical movement.
-
2285 -
Georg Fischer Signet
The 2285 Level Float Switch is suitable for level switching of various liquids, sewage in shafts, tanks, basins or cisterns. The double-chambered float is made of injection molded tough polypropylene that ensures good waterproof protection.
-
DS-0227A -
Ono Sokki
The trouble of rotation machinery is caused most frequently by unbalanced phenomenon of rotating shaft. However, balancing correction on-site is not easy because the conventional vector calculation method with drawing needs quite some time.
-
NUL-226 -
Neulog
This sensor measures angles, rotations, rotation speeds or rotationacceleration. The sensor has a pulley connected to its shaft and the pulley rotation is measured. This sensor has four modes of operation: degrees, rev/s, rad/s, rad/s2.
-
LG-9200 -
Ono Sokki
The LG-9200 is a non-contact type optical detector which emits red visible light and detects the reflected light from the rotating shaft. The reflection mark is used for the detection by affixing it on the rotating shaft. It enables detection at an angle. (reflective mark: HT-011 by Ono Sokki)The LG-9200 has a built-in compact amplifier and outputs the square wave (voltage) after waveform shaping.With a compact and light weight body, performances are upgraded compared to the previous model LG-916.(LG-9200 detection distance: up to 40 mm, response speed: up to 40 m/s)
-
Iris Power LP
Online monitoring of shaft and bearing vibration to identify various failure mechanisms including unbalance, misalignment, looseness, bearing wear, rubbing, hydraulic problems, electrical problems, resonance, and eccentricity of rotating parts prior to failure.
-
AMETEK Sensors, Test & Calibration
When motion is expressed in shaft rotation, we can provide limits that are adjustable throughout the entire range of movement. Rotary limit switches can be used for material handling on crane or winch drums, hoists, lifts, screw jacks, or platforms.
-
PI-5000 -
ETI Precision
The PI-5000 is composed of the PI2500 and the AUX-5000 auxiliary output unit, which when combined gives the unit the capability of testing 4000 ampere breakers, with essentially the same specifications as the proven PI-4000B. The auxiliary unit is smaller than the PI2500, so it can also be maneuvered easily in tight spaces, or lowered into shafts and manholes that would not be possible with a larger single piece unit.
-
DPT-12 -
Physitemp Instruments
DPT-12 Immersion Probe for Liquids - 12'' #304 stainless steel welded shaft. Wooden Handle. Diameter is .3/16'' diameter. Immersible. Maximum temperature 350°C, Time constant 2 Seconds. 5 foot lead. Not isolated.
-
DPT-24 -
Physitemp Instruments
DPT-24 Immersion Probe for Liquids - 24'' #304 stainless steel welded shaft. Wooden Handle. Diameter is .3/16'' diameter. Immersible. Maximum temperature 350°C, Time constant 2 Seconds. 5 foot lead. Not isolated.
-
Magtrol Inc.
Magtrol Load Measuring Pins are temperature-compensated transducers used to measure load and force and provide overload protection. The pins are mounted into machines in place of normal shafts and fitted with strain gauges, allowing them to produce a signal proportional to the measured load.
-
Smartech Inc.
*Max & Min Measurement*Over Range Display*Under range display*A & C Weighting*FAST & SLOW response*Analog AC/DC Outputs for connection to frequency analyzer or X-Y shaft recorder*Datalogger function*Adjustable Alarm Levels*Backlight
-
VE series -
Ono Sokki
VE series are non-contact type of vibration/small displacement detector with high accuracy which can measure the distance between conductor such as metal and sensor’s surface in micron/submicron resolution. It demonstrates its best performance when used for the measurement and control of the axial and surface vibration of rotational shafts such as main shaft of turbines, electric motors, compressors, and of the thickness and width of moving objects. In addition to the measurement of the amount of displacement, a gap detector can also be used for a wide range of other measurement and control applications such as the measurement of the amount of slack or warping. The non-contact measurement process enables to apply no load to rotational or vibration body, and does not affect the material under measurement.
