- Pickering Interfaces Inc.
product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external...show more -
product
DSP Based Serial Communication Board
CPCI-ISC8
The CPCI-ISC8 is an intelligent DSP based serial communication board. This 3U board is based on the CPCIIPC product and has been modified to remove the IPinterface and to support additional I/O features. The CPCIISC8 provides mechanical support and the electrical interfaces for an I/O mezzanine board. Multiple CPCI-ISC8 boards may be installed in a single system.
-
product
PXI-8433, 4-Port, Isolated, RS485/RS422 PXI Serial Interface Module
779539-01
4-Port, Isolated, RS485/RS422 PXI Serial Interface Module—The PXI‑8433/4 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
PXI-8433, 2-Port, Isolated, RS485/RS422 PXI Serial Interface Module
779744-01
2-Port, Isolated, RS485/RS422 PXI Serial Interface Module - The PXI‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
Data Acquisition - 3U 3-Slot
DAQ-33CP0G
is a preconfigured rugged system with a high-performance, low power ARM® Cortex®-A9 processor. It is ideally suited to support a multitude of military/aerospace data acquisition applications that require high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications Dual-Port Gig-E Ethernet.
-
product
PXI-8432, 2-Port, Isolated, RS232 PXI Serial Interface Module
779743-01
2-Port, Isolated, RS232 PXI Serial Interface Module - The PXI‑8432/2 is a high-performance interface for high-speed, port-to-port isolated communication with RS232 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
Multiprotocol Serial Card
PCIe-ICM-4SM
The PCIe-ICM Series are a new family of isolated PCI Express serial communication cards. These PCI Express cards feature a selection of 4 or 2-ports of isolated, software selectable, RS-232, RS-422, and RS-485 serial protocols.
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
40-203-001
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
MACC - embedded
EXC-8000MACC
The EXC-8000MACC is a table driven translator (data converter - protocol converter) that enables devices supporting different communications specifications (e.g. Ethernet, Serial, ARINC 429, Mil-1553, Discretes etc.) to talk to each other.
-
product
PXI/PXIe 1000Base-T1 Dual Multiplexer With Fault Insertion, Dual Channel
42-204-002
The 40-204-002 (PXI) and 42-204-002 (PXIe) are dual channel differential multiplexers designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They are available with support for 1 or 2-channels of two wire serial interfaces. Each channel pair can be looped out to external equipment or the switches can be used simulate a channel open fault.
-
product
OnyxFX Virtex-7 Processor and FMC Carrier - 3U VPX
Model 5973
- VITA-57.1 FMC site offers access to a wide range of possible I/O- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe4 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- LVDS connections to the Virtex-7 FPGA for custom I/O- Optional optical interface for backplane gigabit serial interboard communication- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
product
Serial Board
104-COM232-8 Series
This is an eight, four, or two-port, asynchronous, serial communication board designed for use on the PC/104 bus. It supports full RS-232 serial communications. The board may be installed in any standard PC/104 stack. Connections are made via two 40 pin IDC type right angle connectors for the boards optional breakout cable. The boards are feature-rich and allow for the connection of multiple serial devices—ideal for a variety of applications such as POS, barcode readers, modems, machine monitori...show more -
product
Dual-Channel, Tri-port per channel, for extended cabling up to 4.5 meters
FW2
The FW2 provides IEEE 1394 (Firewire) high-speed serial communications. The module is provided with a direct PCIe interface to the local (on-board) processor, or, an external host processor for board platforms that support external PCIe connectivity. These module(s) are not supported with the classic memory register-based NAIBrd Software Support Kit (SSK) API libraries. These communication function modules support device control and management via standard native OS (Linux) FireWire device driver.
-
product
Low Profile PCI Express 8-Port
7803e
The 7803e low-profile PCI Express serial interface provides eight RS-232 serial ports. For maximum compatibility with a wide range of peripherals, the board supports all standard RS-232 modem control signals. The serial ports utilize 16C954 UARTs with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550...show more -
-
product
PXIe-8431/16, 16-Port, RS485/RS422 PXI Serial Interface Module
781473-02
The PXIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Gen 3 Processor - PCIe
Model 7053
- Supports Xilinx® Zynq® UltraScale+" RFSoC FPGA- 16 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2, and 3) interface up to x8- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- Optional front panel dual optical MPO interface for gigabit serial communication- Unique QuartzXM eXpress Module enables migration to other form factors- Navigator BSP® for software development- Navigator FDK® for custom IP development- Free lifetime applications support- Pentek's Quartz Fami...show more -
product
Ethernet Adapter Supporting up to Twenty ARINC-429 Channels in Any Combination
ES-9810/A0 (RUNET II)
The EXC-9810/Ax is an Ethernet adapter supporting up to twenty ARINC-429 channels in any combination of transmit and/or receive. All of the channels feature error injection and detection.adapter. Its small size and ability to interface through Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the ARINC-429 bus, both in the lab and in the field.The receive channels allow for the storage of all selected labels with status and time tag infor...show more -
product
PXI Dual 18 Channel MUX, 96-Pin SCSI Connector
40-735-912-S1
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the d...show more -
product
Multiple Module Serial Bus Test Instrument
Bi4-Series
The wide variety of serial buses used in defense and aerospace applications typically requires multiple single-purpose instruments. Too often, they are difficult to reconfigure in order to test a different application.The Bi4-Series provides all the capabilities needed for complete communications bus access test for up to four serial buses used in board level (SRA/SRU) and box level (WRA/LRU) equipment—all in a single VXI module.The instrument includes test applications, industry-compliant softw...show more -
product
JadeFX FlexorSet 4-Ch. 250 MHz A/D w/DDCs, 2-Ch. 800 MHz D/A w/DUC, Int - 3U VPX
Model 5983-313
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family BrochureVITA-57.4 HSFC FMC+ site offers access to a wide range of possible I/O- Supports Xilinx Kintex UltraScale FPGAs- Four 250 MHz 16-bit A/Ds- Four multiband DDCs- One digital upconverter- Two 800 MHz 16-bit D/As- Extended Interpolation- Sample clock synchronization to an external system referencePCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable...show more -
product
Serial Card
PCIe-COM232-8
ACCES I/O’s PCI Express multiport serial communication cards deliver eight (PCIe-COM232-8) or four (PCIe-COM232-4), high-speed, RS-232 ports for use in a wide variety of applications. The cards were designed to offer serial compatibility with the PCI Express bus and to be used by system integrators and manufacturers in the design of industrial and commercial systems.
-
product
3U Processor Board
CP39104
LinkedHope Intelligent Technologies Co.,Ltd.
Designed for industrial communication, CP39104 is a 3U CPCI serial card compliant with PICMG 2.0 R3.0 specification.CP39104 applies XR17D154 serial communication controller of EXER, and supports 4x RS232/RS422/ RS485. Therefore, CP39104 is highly suitable for testing and measuring in serial data communication applications.LinkedHope® provides CP39104 with a wealth of software drivers and BSP, including VxWorks, Linux, Windows, etc., to enable a wide range of application scenarios.
-
product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
product
PCI-104 8-Port, 4-port, And 2-port Multi-Protocol RS-232, RS-422, RS-485 Serial Communication Boards
104i-COM-8SM Family
The 104i-COM-8SM (PCI-104) family of multi-port, multi-protocol (RS-232, RS-422, RS-485), serial communication boards deliver up to eight high-speed serial communication ports for use in a wide variety of applications. The boards were developed for use by system integrators and manufacturers in the design of industrial and commercial systems. Based on the XR17D158, the boards have eight enhanced 16550 UARTs, each with a set of modem signals (CTS, RTS, RI, DTR, DSR, CD) in RS-232 mode. Each UART has both a 64 byte transmit and a 64 byte receive FIFO. Ports are accessed via two 40-pin IDC type right angle header connectors. 2 and 4-port versions are available, as well as RS-232 only models.
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787458-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-...show more -
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 3-Channel
42-203-001
The 40-203-001 (PXI) and 42-203-001 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 3 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
USB-485/4, 4-Port, USB, RS485/RS422 Serial Interface Device
778476-104
The USB‑485/4 interface transforms your USB port into a single asynchronous serial port for communication with RS485 and RS422 devices. You can use a USB‑485/4 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
OnyxFX FlexorSet 2-Ch. 3.0 GHz A/D, 2-Ch. 2.8 GHz D/A - 3U VPX
Model 5973-320
- Includes Xilinx Virtex-7 FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Two 3.0 GHz A/Ds- Two 2.8 GHz D/As- Two digital downconverters- Two digital upconverters- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- LVDS connections to the Virtex-7 FPGA for custom I/O and...show more -
product
3U cPCI Serial Power Backplanes
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system’s card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections.
-
product
Modular I/O via Ethernet
2601 Series
100/10 Mbps Ethernet gateway to 2600 series I/O modulesFour RS-232/422/485 ports for remote serial devicesIntegral support for interlock and emergency stop circuitsNetwork watchdog shuts off I/O upon client faultHigh-performance network stack: up to 1000 transactions/secondUltra-fast, one second boot-up timeOptically isolated serial communication to I/O modulesWatchdog TimerCE CompliantCompatible with Linux and Windows
