Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
product
PXI BRIC4 FIBO Matrix Dual 40x4 3pin brkout
40-592A-002
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
product
*Laser Power & Energy Meters
Ophir laser power meters work on the smart plug principle. This means that almost any Ophir power meter can work – plug and play – with almost any of the wide range of Ophir sensors. Ophir power meters are also the most precisely calibrated units on the market thus measuring with the highest accuracy. Noted for their versatility, ease of use, and user friendly interface, Ophir meters can be used stand-alone or interfaced with LabVIEW or the user's own software.
-
product
12-bit, 200KHz, 16SE/8DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-16
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
product
Integrated Current Sensors
HMSR series
*SOIC 16 compatible footprint*Great accuracy: Typical accuracy is 0.5% over temperature and the measurement range -Small hysteresis of <<0.5%*Strong immunity
-
product
Humidity Sensors
A humidity sensor is a device that detects and measures water vapor. TE Connectivity (TE) manufactures a complete range of calibrated and amplified RH sensor products to measure relative humidity. Based on our robust capacitive technology, these humidity detectors provide accurate measurement of dew point and absolute humidity by combining relative humidity (RH) and temperature (T) measurements.
-
product
Data Logger MSR255 with LCD screen
MSR255
With up to five different sensors, four additional analogue inputs and an easy to read LCD screen the compact MSR255 offers maximum possible flexibility and user-friendliness.
-
product
SmartRock™ Plus
SmartRock™ Plus is a solution offered by ready-mix producers that enables contractors to monitor the strength and temperature of early-age concrete in real time. Contractors install wireless sensors on the rebar, then monitor real-time temperature and strength results on the iOS or Android app for quick decision-making during the concrete curing process.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-134
The 40-297A-134 (PXI) and the 42-297A-134 (PXIe) are 4-channel programmable resistors with a range of 2 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Connect PT100/PT1000 Sensors To Output A Voltage Signal
K- PT100/1000
Our K-PT module is designed to connect up to PT100/PT1000 sensors and simply provides an output voltage signal. Thus enabling the most standard voltage measurement devices to work with PT100/PT1000 sensors. The PT100 sensors offer excellent accuracy and repeatability.
-
product
Linear Motion Potentiometers
A spin-off of the Trimpot trimming potentiometer product line, the linear motion potentiometer was developed to meet the needs of designers wishing to detect movement of position. Applications for these compact components include: Solenoid positioning sensors for automated controllers, volume control on audio equipment, joystick controllers, satellite dish positioning, and robotics.
-
product
ISC-1781, 1.3 MP, 1.58 GHz Processor, Monochrome/Color Smart Camera
785147-01
The ISC‑1781 is a high-performance smart camera for machine vision and is powered by a 1.58 GHz dual-core Intel Celeron processor. The combination of the onboard processor with a CMOS image sensor provides an easily distributed all‑in‑one system. In addition to high-performance image acquisition and processing, you can use built-in digital I/O and industrial communication options for dynamic, real-time communication and integration with industrial automation devices including programmable logic ...show more -
product
Current Clamps and Transducers
High-accuracy Current Sensors and TransducersHigh-accuracy sensors for AC/DC current measurement and power analysis. From current clamps to high-precision zero flux current transducers and Rogowsky coils.
-
product
Socket Wrench Torque Sensor Reaction Type
SWS SERIES
Our SWS Series reaction type socket wrench torque sensors are available in ranges from 10 ft-lbs. through 1000 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. These low cost sensors deliver high accuracy and outstanding frequency response. alibration of mechanical torque wrenches may be performed with this sensor. The sensing element incorporates bonded foil strain gages of the highest quality.
-
product
Single Channel Signal Conditioner
SAM-3
Macintyre Electronic Design Associa
The SAM-3 is a portable single channel signal conditioneer specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from eitherits internal batteries or the power line. It incorporates two sets of power line rejection fileters, switch selectable fro 50 to 60 Hz and the corresponding first four harmonics.
-
product
Resistance Temperature Detectors
Sensors used to measure temperature by correlating the resistance of the RTD element with temperature.
-
product
Refractometer Parts and Accessories
MISCO is the source for all your refractometer parts and accessories. Parts are available for the MISCO traditional analog refractometer, the Palm Abbe digital handheld refractometer, inline/process refractometers and sensors, as well as benchtop/laboratory refractometers.
-
product
Multifunction Calibrator 15 ppm Basic Accuracy
MC142
Multifunction calibrator MC142 is a precision voltage, current and power calibration source serving as a measurement standard in calibration laboratories and production lines; where verification of electrical measurement equipment & sensors is required. It can be used for calibration and adjustment of meters measuring voltage, current, power, resistance, capacitance and frequency. Internal harmonic and non-harmonic signals make it possible to test electrical performance of meters using sig...show more -
product
Eddy Current Probes and Drivers
Proximity sensors work on the eddy current principle. A proximity system consists of an eddy current probe, extension cable and driver. A high-frequency RF signal is generated by the driver, sent through the extension and probe cables and radiated from the probe tip. The tip consists of a precision wound copper coil inside a chemical and temperature resistant PEEK case.
-
product
Multi Monitor
MD
It is a 30mm monitor with 2 screens and 3 colors that displays 1-5V analog signals converted into numerical values.Since various unit displays are possible, it is ideal for monitoring pressure sensors and flow rate sensors.
-
product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 31.5Ω
40-251-010
The 40-251-010 is a programmable resistor module with 8 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
product
Temperature and Humidity Duct Probe
T0213
Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Speed Sensors
Speed sensors for both indoor and outdoor environments with options featuring kits for motors, geartooth pickup, tachometers, and stroboscopes.
-
product
USB-6001, 8 AI (14-Bit, 20 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device
782604-01
8 AI (14-Bit, 20 kS/s), 2 AO (5 kS/s/ch), 13 DIO USB Multifunction I/O Device - The USB‑6001 is a low-cost, multifunction DAQ device. It offers analog I/O, digital I/O, and a 32‑bit counter. The USB‑6001 provides basic functionality for applications such as simple data logging, portable measurements, and academic lab experiments. The device features a lightweight mechanical enclosure and is bus powered for easy portability. You can easily connect sensors and signals to the USB-6001 with screw-terminal connectivity. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
product
High-resolution Cameras / 9 & 12 MP with up to 40 fps
ace L Series
Twelve ace L models offer resolutions of 9 and 12 megapixels and frame rates of up to 40 fps. Featuring the high-performance IMX253, IMX255, IMX267 and IMX304 sensors, they stand out for the famously brilliant Pregius image quality with a dynamic range of more than 70 dB and a high quantum efficiency over a broad spectrum of visible light into the NIR. Available with the proven GigE or USB 3.0 interface, and conform to GigE Vision 2.0 or the USB3 Vision standard.
-
product
Wind Speed and Wind Direction Sensors
Wind vanes measure wind direction and are often used with anemometers, which measure wind speed. Campbell Scientific offers a variety of anemometer designs: cup, propeller, ultrasonic, sonic, and lidar. Most of our wind sensors are modified slightly from the manufacturers’ stock items so that they may be used with our dataloggers in research, air quality, and general purpose meteorological applications.
-
product
Calibration Tool
Software
The smartGAS Calibration Tool is a commercial software company that makes it possible to interact with all smartGAS sensors of the EVO series with firmware version 5.17 or higher. With the smartGAS Calibration Tool, it can be read out and the zero point and the end point can be used with a suitable test gas.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 3.5Ω To 1.51MΩ
50-298-044
The 50-298-044 is a high density programmable resistor card with 6 channels which can be set between 3.5Ω and 1.51MΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Stamper Thickness Measurement Gauge
6360-HR-CD
The Model 6360-HR-CD Stamper Thickness Measurement System is a semi-automated thickness gauging platform and data analysis system for the measurement of optical media stampers. Patented non-contact capacitive sensors determine the stamper thickness without any damage to the stamper. A personal computer is provided to run the gauging platform, acquire measurement data and display results.
-
product
Instrumentation
Complementing our range of force and torque sensors, we offer a comprehensive range of graphical displays, including the Digiforce, which are PLC controllers and data loggers all in one. Together with a fully comprehensive range of standard high speed load cell displays with analogue output.
-
product
Adjustable Range Reflective Photoelectric Sensor
EQ-30
Panasonic Industrial Devices Sales Company of America
The compact EQ-30 Adjustable Range Reflective Photoelectric Sensor is only 68 x 20 x 40mm but delivers amazing performance. Normal Reflective Type Sensors operate by sensing the variation in the amount of incident beam. However, the Adjustable Range Reflective Sensing Type Sensors, incorporate a 2-segment photodiode to sense variation in the incident beam angle. Thus, the output is activated according to the distance of the object from the Sensor. This system helps the EQ-30 Series to be unaffected by object color or a background, enabling stable sensing. The robust housing offers IP67 protection allowing the EQ-30 Sensor to be used in the most demanding industrial environments.