-
product
Corrosion Test Chamber
CME SF-CCT
CME SF-CCT chambers are designed to be flexible enough to comply with as many different CCT specifications as possible. These may be programmed to conduct a whole range of corrosion tests such as wet cycle, dry cycle, controlled humidity as well as the salt spray test in a single chamber. This can occur in any sequence and be repeated automatically. A wide range of optional accessories enable additional climates to be added to further extend the number of climates and conditions that can be created.
-
product
Flow Meter
Model 001
It provides a cost-effective and reliable method of monitoring flow in a variety of environments, including salt, fresh and effluent water, from shallow streams to tidal waterways. The meter benefits from the design of the impeller bearings, which give low threshold velocity and consistent performance. Available as either wading or a suspension set, all systems are supplied with the Model 0012B real-time control display unit.
-
product
Salt Spray Testing
Salt Spray testing (Also known as Salt Fog testing) is often used for testing the corrosion resistance of metallic products, or for testing the corrosion resistant coating applied to metallic products, in order to verify that they will function properly when exposed to salt corrosion. This specific type of testing is used as a means to accelerate the salt corrosion exposure in order to gather data on the long or short term effects of salt corrosion on the product or coating material.
-
product
Elcometer Bresle Test Patches
135C
The Elcometer 135C Bresle Test Patches determines the concentration of soluble salts on uncoated surfaces in accordance with the ISO 8502-6 test method.
-
product
Environmental Testing
Large Walk-in Environmental Chamber, and Walk-in Salt Fog Chamber, various sizes of vibration and shock equipment, and environmental chambers.
-
product
Chloride Ion Test Kit for Water
134W
The Elcometer 134W is used to monitor recycled water (after it has been applied) to establish effectiveness of salt removal, this test is ideal for testing the salt contamination in wash water and blast water.
-
product
Sodium Ion Concentration Pocket Water Meter
LAQUAtwin Salt-22
The only pocket meter that directly measures sodium ion concentration in 0.3ml sample (or 0.05ml sample with sampling sheet B) and converts it into salinity or NaCl salt concentration. No need for a beaker to calibrate the meter or measure a sample. Just place few drops of the standard or sample onto the sensor. This procedure saves you time and prevents wasting your precious sample.
-
product
Salt Spray, Salt Fog & Cyclic Corrosion Testing
We service most industry segments with harsh environment, salt fog corrosion testing.If your product is coated or painted for the marine, automotive or military industries, we are equipped to provide accredited testing within multiple chambers.We provide ASTM sample preparation for coated and painted articles to ensure that your test is performed correctly.We also provide custom configurations with varied salt concentrations and temperatures for many customers with products that are used in unique environments. Products like circuit boards, electronic devices and sensors may all have specialized testing requirements.
-
product
Polydisperse Generators
This type of generator is typically capable of spraying aqueous solutions (e.g. salt), suspensions (e.g. PSL, nanoparticles), or oil or alike substances. They serve a variety of applications from laboratory research field tests of detectors, and filter testing.
-
product
Salinity Testers
Labodam pocket salinity testers are equipped with platinum sensors, providing fast and reliable results measuring the salinity of water and other low and high salt concentrated solutions. Equipped with replaceable electrodes, helping to reduce maintenance cost.
-
product
Environmental Test Services
Capabilities include extreme low and high temperature testing with fast transition rates with chambers of varying size to fit your products; Temperature Shock, Altitude tests up to 100,000ft at various temperatures, Vibration and Shock testing according to your specs, Humidity testing with chambers of varying sizes including up to a 10' by 10' walk-in chamber, Combined Vibration and Temperature testing is available using our Agree chamber, Immersion tests, Drop tests, Salt Fog and others
-
product
Corrosion (Salt Spray Tester)
This device is used to test the surface treatment of various materials.
-
product
Climatic Test Chambers
Dongguan Amade Instruments Technology Co., Ltd
Climatic test chambers are also referred as environmental test chambers, which is the general name of various test chambers that simulate the natural climate environment of raining, high temperature, low temperature, constant temperature, illumination, dewing etc, products including constant temperature chamber, constant humidity chamber, ozone aging test chamber, UV accelerated weathering tester, vacuum hot air oven, salt spray chamber, steam aging tester, rain test chamber, dust proof test chamber, ventilation aging chamber, xenon lamp weathering test chamber and so on.
-
product
TDS/Conductivity And PH Testing Instruments
DS & pDS Meters™
No water supply is completely pure. Every industrial, commercial, or natural source contains dissolved solids or salts. These impurities contribute to scale, corrosion, poor taste, and environmental pollution that endanger animal and plant life. Myron L® Company has two proven ways to measure such impurities. Our DS Meters™ provide fast, accurate, on-the-spot measurements of total dissolved solids (TDS) or conductivity. pDS Meters™ test conductivity or TDS, plus pH. Readings from their highly stable circuitry help assure product quality, prevent equipment damage and verify in-line instrumentation in a wide range of applications.
-
product
Bresle Salt Meter
Elcometer 138
Incorporating a flat sensor, the Elcometer 138 Bresle Salt Meter measures the conductivity of a sample, then automatically converts this to show the density of salts, negating the need for the user to do a manual calculation when working in accordance with ISO 8502-6 or ISO 8502-9.
-
product
Benchtop Water Hardness Meter
LD-LBWM-A10
Benchtop Water hardness meterLD-LBWM-A10is equipped with large backlit LCD display, 2 to 5 points calibration with low to high concentration range. The calibration due reminder alerts user for calibration of the meter on regular basis. The System menu allows setting the 7 parameters like stability condition, auto-power off etc. It measure salts of calcium & other elements at mg/L, mmol/ scale which causes hardness water.
-
product
Salt Spray and Fog chamber
P700
Bemco's Standard P700 Salt Spray and Fog chamber is designed to fill the needs of laboratories that require accurately controlled salt spray and fog tests on small components and assemblies. This unit meets all standard military, commercial, and ASTM salt fog corrosion and humidity corrosion tests.
-
product
Epoxy Resin Silicon Rubber Outdoor Voltage Transformer
JDZW-10RG
Beijing GFUVE Electronics Co.,Ltd.
Outdoor voltage transformer of the type JDZW-10 is single phase and epoxy resin silicon rubber insulated product, it's used for metering electric energy, voltage control and relay protection in 50/60HZ rated voltage less than 12kV electric system. It can be used for medial voltage AIS, or can be used for medial voltage switchgears. They can operate in all kinds of environments (such as wide range temperature (-50~70℃), high altitude, high humidity, high pollution or salt). This model JDZW-10 outdoor voltage transformer is also as voltage source to supply 220V voltage.
-
product
Environmental Testing
D.L.S. Electronic Systems, Inc
D.L.S. Conformity Assessment provides testing services for environmental tests under its accredited ANAB/ACLASS ISO 17025 program. This globally accepted accreditation covers environmental and mechanical testing that include vibration and shock, temperature extremes , sand and dust, fluid and chemical resistance, altitude, humidity, salt spray, ingress protection, icing, flammability and other related testing services.
-
product
Salt Spray Corrosion Test Chamber
CX-Y60L
Shenzhen Chuangxin Instruments Co., Ltd.
Laboratory Salt Spray Corrosion Test Chamber for Nss / Acss / Cass Test is used to test the anti-erosion quality of the surface of all materials after the rust-proof of painting, coating, electroplating, anoding and rust-proof of greasing.anti corrosion treatment for a variety of materials, corrosion resistance of their products.
-
product
Salt Spray Testing/Cabinet Based Corrosion Testing
Sometimes referred to salt mist, salt fog, humidity or corrosion testingAll corrosion and environmental related tests can be tailored to customer requirementsTypical exposure times range from 16 hours to over 1000 hoursAccelerated corrosion testing can be used to check protective coatings, surface finishes and material compatibilitiesOur facilities provide a continuous controlled corrosive exposure and can combine salt spray and humidity environments.
-
product
Corrosion Test
The purpose of this test is to determine the resistance of materials and protective coatings to corrosive atmospheres when a more corrosive environment than the salt fog/spray test is required. The test is used when material is stored or operated in areas, for example, where acidic atmospheres exist, such as in industrial areas or near the exhausts of any fuel-burning device. Gases such as sulfur dioxide are used to replicate the exhausts of fuel burning devices.
-
product
Surface Cleanliness
Surface cleanliness: Soluble salts & ion specific contamination (sulphates, chlorides, nitrates etc.) which are often invisible to the eye, together with amine blush (for amine cured epoxy coatings) can result in premature coating failure, resulting in high re-coating and maintenance costs. Elcometer has a range of test equipment for assessing surface cleanliness prior to applying a coating.
-
product
Walk in chamber for Complex Salt Spray Test (Temperature controllable)
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in chamber for Complex Salt Spray Test Relevant standards requirement1. Test Object: battery pack andsystem.2. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.3. The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water，Its concentration is (5 + 1)% (mass fraction).4. (35 ± 2) ℃, the measured pH value is between 6.5-7.2.5. Placed the test objects in the salt spray chamber for cycling test. Ea...show more -
product
Salt Spray Test Chamber
Dongguan Kejian Instrument Co., Ltd.
Corrosion resistance salt spray testing machine can be used to determine the corrosion resistance of inorganic or organic coatings of ferrous or non-ferrous metals, such as electroplating, anodizing, chemical processing, painting and other surface treatments.
-
product
Salinity Logger Sensor
NUL-228
This sensor enables measurements of the salt content in a solution in three ranges: %, ppm and mg/L.The sensor is pre-set factory calibrated and immediately ready to use.
-
product
Sodium Chloride Salt Brine Refractometer Salometer
PA202X-076-168
Fahrenheit model – The Palm Abbe Digital Salometer now makes it easier and more accurate than ever to measure the saturation (SAL) and freeze point of Sodium Chloride (NaCl) Salt Brine Solutions. Only two drops of fluid are needed to automatically measure degrees saturation, from 0 to 100%, and Freeze Point to -6 degrees Fahrenheit.
-
product
Seawater Refractometer
AQUAR-H5O
The Palm Abbe AQUAR Digital Seawater Refractometer is a professional refractometer for testing seawater, salt water, and brackish ocean water for oceanography, aquaculture, aquariums, desalination plants, and ocean research. The model AQUAR-H5O measures seawater salinity in Practical Salinity Units (PSU), Sigma-t Density, Specific Gravity, Conductivity, and Chlorinity.
-
product
Corrosion Test Chambers
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Corrosion test chambers for salt spray testing is used throughout the automotive, aerospace, fasteners, electronics, paints and coating industries!
-
product
Environmental Testing Equipment
It is to do adaptability and properties test for materials under different environment conditions, which includes salt spray test to determine corrosion resistance and temperature and humidity chamber to do a variety of high-low temperature alternating test.
