- Virginia Panel Corporation
product
VTAC Wired
VTAC Wired configurations reduce resistance and increase signal integrity with a seamless transition from wire to connector. This can be demonstrated in an example using the results of VPC quality and performance testing on VTAC patchcords. The results are reflected in the graph below. Insertion loss was tested on one-meter long patchcords with SFP+ terminations on either end. The second data line (red) shows the same patchcord, but bisected and terminated with VTAC connectors in its center. The...show more -
product
SFP BIDI
2.5 Gbps LC BIDI
Is specifically designed forhigh performance integrated duplex data link overbi-directional single mode optical fiber. Thehigh-speed laser diode and photo diode areprovided as a light source and a detector,respectively.
-
product
Intel® Xeon® E3 Quad-Core 10 Gigabit Ethernet AdvancedTCA® Processor Blade
aTCA-9300
The ADLINK aTCA-9300 is a high performance AdvancedTCAR (ATCA) processor blade featuring dual 4-core IntelR XeonR processor E3 1275V2 /1225V2, IntelR C216 Chipset, four channel memory up to 32 GB of DDR3 memory and 300 W power supply subsystem. Versatile connectivity includes dual 10GbE Fabric Interfaces, dual GbE Base Interfaces, quad front panel GbE egress ports, front panel dual COM and USB 2.0 ports and front panel VGA connector. An onboard SATA connector supports CFast up to 32 GB and the o...show more -
product
SFP
4 Gbps
Is specifically designed for high performance integrated duplex data link over multi mode optical fiber. The high-speed oxide VCSEL and photo diode are provided as a light source and a detector, respectively.
-
product
FMC Card with Four SFP+ 10 GBit Ports
TEF0008-02
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0008 is a FPGA to Mezzanine Card (FMC) based on VITA 57.1 FMC HPC Standard, with four SFP+ 10 GBit ports for fiber optical SFP modules. It is inteded for use on a FMC HPC carrier and can not be used stand-alone.
-
product
Fiber Cable, Multimode, OM3, 50m
784184-50
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
Optical Limiting Amplifiers
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
product
Cyclone V based 6U cPCI COTS Module
iWave’s Cyclone V based 6U cPCI Card is a rugged standalone module complaint with 6U size CPCI PICMG 2.0 Rev 3.0 backplane, aimed for the high-speed data, video processing, and display applications. The card offer speed up to 512MB/s of DMA transfer and up to a 6 channels of transceiver interfaces capable of operating up to 6 Gbps, SFP, Built-in health monitoring circuits, DVI Input, and Output Interfaces
-
product
CWDM SFP Transceiver Tester for Installation & Verification
ZonuCheck
Hand held instrument combines: Transceiver Tester (Tx power and Rx sensitivity),CWDM (Wavelength selective) Optical Power Meter, Media converter (enables GbE connectivity to bypass customer CPE) and datalogger. The new Tester makes the installation, service and maintenance of an SFC Access Network a ?snap? for Field Technicians. Optimized for our SFC Transceivers and Passives, the ZonuCheck? Handheld Tester may be used in any CWDM application to identify ITU CWDM Wavelengths and measure the Optical Power levels for the ten (10) commonly used ITU CWDM Channels.
-
product
1U Rackmount Network Appliance Platform With Intel® Xeon® Processor D-1527/ Pentium® Processor D1508 And 10 LANs
NA720
The NA720 is built on the server-class Intel® Xeon® D-1527 processor (codename: Broadwell-DE) and Pentium® processor D1508. The NA720 comes with two 10GbE SFP+ ports, eight Gigabit Ethernet ports and two expandable LAN modules supporting 1GbE/10GbE/Fiber/Copper/Bypass with a maximum of 26 LAN ports. Four DDR4-2400 MHz R-DIMM/U-DIMM sockets can provide system memory of up to 128GB and support both ECC and non-ECC memory types. For storage, it supports one mSATA and two 2.5” SATA hard disk drives. This high performance Intel® Broadwell-DE network appliance is an ideal solution for enterprise firewall, network bandwidth controller and UTM applications.
-
product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
6-Port Hardened Industrial Gigabit Ultra PoE DIN-Rail Switch
TI-UPG62
4 x Gigabit Ultra PoE ports2 x dedicated SFP slots240 watt power budget12 Gbps switching capacityHardened IP30 rated metal switchIncludes DIN-rail and wall mountsExtreme -40 to 75 ºC (-40 to 167 ºF) operating temperature rangeDual redundant power inputs with overload current protectionAlarm output triggered by power failurePower supply sold separately (TI-S24048)
-
product
PrAMC Based On QorIQ P4040/P4080, 10 GbE, SFP+
AMC710C
The AMC710C is a flexible processor AMC for general purpose processing with the quad-core QorIQ P4040 with Data Path Acceleration Architecture intended for router and UTM (unified threat management) applications.
-
-
product
4-port LAN Module With Intel® I350-AM4/I211-AT Ethernet Controller
AX93336
The AX93336 LAN module is built with an Intel® I350-AM4/I211-AT GbE Ethernet controller, incorporating Jumbo Frames and Intel® VT-c (Intel® I350-AM4) to optimize network traffic processing. It also comes with an optional LAN bypass function to ensure smooth network connectivity at all times, making it an ideal solution for users seeking better protection of their essential business communications in the event of a power outage, system shutdown or crash. This LAN module’s high-density design is s...show more -
product
Single Channel SFP+ All-In-One Sensitivity Tester
SFP+ Tester
All in one mainframe to perform a complete sensitivity test on a single channel fiber optic transceiver. Includes Clock source, BERT and all optical modules
-
product
Fibre Channel XMC Interface Module
XMC-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
Transceiver Driver
S-112
Transceiver Driver slot module of FOTS system is an efficient module for the characterization of SFP type transceiver and the test of optical line or components. This module is a kind of Small Form Factor Pluggable(SFP) host board that can be used to test SFP transceiver modules to define the modules’ performance. The transceiver driver slot has two SFP cage and 20-pin SFP connector sets to mount and control two SFP transceivers simultaneously.
-
product
Fibre Channel Test & Simulation Interface for PCI
PCI-FC4
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
product
COM Express Type 7 Development Baseboard
CEB94701
*Two 10GBASE-KR SFP+ ports*2 SATA-600*VGA*4 USB 3.0*2 PCI Express Mini Card slots*2 RS-232/422/485
-
product
24 Port CPCI Managed Layer Two Switch
CP217
The CP217 is a 6U single slot Compact PCI (cPCI) module that has 24 ports of GbE. Eight ports via RJ-45 and four ports via SFP as a single slot. The Module come with an optional daughter board which has an additional 12 ports of GbE via SFP which can provide Fiber or Copper interface.The switch is managed via http and supports a rich set offeatures such as VLAN, Spanning tree, QoS, Mirroring, etc.
-
product
X-Ray Detector
XRT Detector Onyx
ONYX 1412-X is a performance-leading X-ray detector comprising a proprietary 2768 × 2376 active pixel sensor array of 50 × 50 µm pixels. This detector consists of a high-speed, low-noise, radiation-tolerant, 14 × 12 cm, 6.6M pixel CMOS image sensor, with a directly deposited high-resolution CsI scintillator on Fibre Optic Plate. The highly configurable sensor is accessed through a software interface, connected via a 10 GbE SFP+ hardware interface.
-
product
1U Rackmount Network Appliance Platform With Intel® Atom® Processor C3558/C3758 And Up To 10 LAN
NA362R
The NA362R is powered by the Intel® Atom™ processor C3558/C3758 (Codename: Denverton). The low power 1U network appliance comes with six 10/100/1000 Mbps LAN ports and two or four 10 GbE SFP+ fiber ports. It is equipped with one pair latch-type LAN Bypass function for fail-over option as well as featuring BIOS console redirection. Furthermore, it supports the Intel® QuickAssist Technology which accelerates data processing and compresses cryptographic workloads. The network communication applianc...show more -
product
NEXT GENERATION RADIO PLATFORM
INTEGRA S
Integra S is an unbelievably light, energy efficient carrier-grade system that exemplifies an outstanding return on smart engineering - the synergy of high competence in radio electronics and materials science. Slip-fit design allows integration with existing high performance antenna systems or integration with 2+0 aggregation setups for up to 954 Mbps Full Duplex capacity without header compression. Gigabit Power over Ethernet (PoE) port defies simple installation, while dual SFP slots allow for fiber optic installation – giving the user ultimate flexibility in cable design.
-
product
SFP+ Cable, 3m
784076-03
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
product
Bi-directional SFP Modules
BiDi SPF
The DIAMOND SA flexos BiDi-SFP modules (transceivers) make it possible to transfer data via fibre optics. The Bi-Di SFP modules are available in single-mode and Gigabit Ethernet. The SFPs have metal housings with latches for the simple removal of the module. They are compatible with connector types F-3000™ and LC.
-
product
Configurable & High Density Signal Transport
VF-9000 Series
Life on a mobile production truck or ENG van means making the most of your surroundings. With limited real estate for technology, our customers need high-density platforms to manage the abundance of signals coming in and going out. MultiDyne’s VF-9000 Series is built for high-pressure sports, news and live event production scenarios, and high-capacity transport requirements between studios and across campuses. The VF-9000 Series is also remarkably intelligent, providing automatic configuration o...show more -
product
Multi Checker
AMC-70
AMC-70 can check SFP TX and RX power level by simply inserting SFP into it. If you use UPM (Universal SFP-typed Power Checker Module) provided. AMC-70 can measure optical power.
-
product
1000BASE-T1 MEDIACONVERTER EMC
Art.-Nr.: TE-1404-1
The ideal solution for working quickly and efficiently with 1000BASE-T1 EMC measurements The 1000BASE-T1 MediaConverter EMC is especially designed for measurements within the EMC chamber. It is delivered in a Set with an adapter board which enables internal PHY status readings and provides one point-to-point connection between Automotive Gigabit Ethernet and SFP Gigabit Ethernet, with which optical fibre modules are used.
-
product
100Gbps Ethernet Packet Generators
Axtrinet (AXTRINET IS A TRADING NAME )
1x 100GbE QSFP28 port, 4x 25GbE SFP28 / 10GbE SFP+ / 1GbE SFP ports, Status Indicators
-
product
EDFA Optic Amplifiers
Wuhan Sunma Technology Co., Ltd.
With the feature of high input power, high output power, and medium optical gain, the booster amplifier operates at the transmission side of the link to amplify aggregated optical input power for reach extension.SunmaFiber booster amplifier is a low-noise, gain-flattened C-band optical erbium doped fiber amplifier (EDFA) designed to cost-effectively extend the optical link power budget for building long distance DWDM solutions.SunmaFiber also offers switches, routers and fiber converters includi...show more
