-
Product
SFP BIDI
2.5 Gbps LC BIDI
-
Is specifically designed forhigh performance integrated duplex data link overbi-directional single mode optical fiber. Thehigh-speed laser diode and photo diode areprovided as a light source and a detector,respectively.
-
Product
Linear Equalizers
-
Macom Technology Solutions Holdings Inc.
MACOM offers high-performance linear equalizers for use in high speed copper connections for Ethernet, InfiniBand and Fibre Channel. The product line supports NRZ and PAM-4 multi-level signal connectivity and builds upon MACOM’s long-standing expertise in equalizers for broadcast video applications. The equalizers can support up to 112Gbps per lane data rates for 50 Gbps to 800 Gbps copper cable assemblies. In addition to copper cables, the linear equalizer can be used for wired backplane and on-board applications. Adding linear equalization to a passive copper cable can enable the same copper cable to carry higher data rates for longer distances. MACOM’s new linear equalizer product line can extend a typical copper cable’s performance to 7.5 meters at 56 Gbps and 5 meters at 112 Gbps data rates. Customers can consider active copper cables as an alternative to passive copper cables or active optical cables. Key benefits include low power consumption from a single 3.3V supply, low latency, hardware and microcontroller management modes. The products are suitable for SFP, QSFP, QSFP-DD and OSFP connector form factors.
-
Product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
-
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
6U CompactPCI 10 Gigabit Ethernet Switch Blade
cPCI-6S10
Switch Blade
- ARM Cortex-A9 processor integrated in Broadcom BCM56150 switch- 24-port fully managed Gigabit Ethernet switch- Pre-installed ADLINK PacketManager accelerates packet processing- Layer 2/3 switching with advanced support for VLANs, QoS and IPv6- Two 10 Gigabit Ethernet SFP+ uplink ports- Supports IPMI based on PICMG 2.9 (System Management Specification)
-
Product
2-Port SFP Ethernet Card With HSR/PRP
ECU-P1524PE
-
CE/FCC CertificationSupport HSR Protocol (IEC 62439-3 Clause 5)Support PRP Protocol (IEC 62439-3 Clause 4)PCI Express Extension2 x SFP Interface (For Ethernet Comm.)2 x SFP Interface (For HSR/PRP)1 x RJ45 (Interlink)Support IEEE 1588Operation Temp: -25~ 70°C
-
Product
3U cPCI Serial Dual-Port SFP+ 10Gbps Ethernet NIC
SN5-TOMBAK
-
The SN5-TOMBAK is a peripheral slot card for CompactPCI® Serial systems, with a dual port 10Gbps Ethernet controller. Both ports are available via SFP+ front bezel connectors for optical cables via SFP+ transceivers or SFP+ twinaxial copper cables.
-
Product
1U Network Appliance With 12th/13th/14th Gen Intel® Core Processors For Network Security And Management For Network Security Applications.
FWA-3034
Network Appliance
12th/13th/14th Gen Intel Core Processors, up to 24 Cores/32 Threads, Hybrid Performance & Efficiency CoresDDR5 UDIMM with up to 64GB2 x 1GbE SFP, 8 x 2.5GbE RJ-45, 2 x 10GbE SFP+ with two pairs of LAN bypass2 x internal 2.5” SATA SSDs/HDDsIPMI v2.0 compliant BMC1 x Advantech network module expansion
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboardError Injection including Runt Frames, Short IFG, and Invalid MAC FCS - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Fanless Network Appliance For SD-WAN & UCPE Edge Deployment With Coming 5G & Wi-Fi 6 Support. Ideal For SD-WAN Deployments.
FWA-1112VC
Network Appliance
Intel® Atom® C3000, up to 8 CoresIP40, fanless design, -20 ~ 70°C temperature rangeUp to 4 x 1GbE RJ-45, 2 x 10GbE SFP slots or 1 x 1GbE SFP, 6 x RJ-45 slots5G, LTE and Wi-Fi 6 RF certifiedIntel® QAT integrated2 x PoE+ support (optional)
-
Product
Compact Network Appliance Platform With Intel® Atom® Processor C3000 Family, Six GbE And Four SFP+ Ports
NA362 for vCPE
-
*Intel® Atom® processor C3000 family (Denverton)*Four DDR4 R-DIMM up to 128GB or U-DIMM up to 64GB memory*Six 10/100/1000 Mbps Ethernet ports and four SFP+ ports*Wi-Fi/3G/LTE through PCI Express Mini Card slot*Supports Intel® QuickAssist Technology*Supports Intel® Data Plane Development Kit (Intel® DPDK)*Suitable for VPN, vRouter, firewall and other vCPE applications
-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
-
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
Product
Desktop Network Appliance Platform With Intel® Atom® Processor C3338/C3558/C3758 And Up To 10 LANs
NA362
-
The NA362 is powered by the low power consumption Intel® Atom™ processor C3338/C3558/C3758 (Codename: Denverton). In addition to six 10/100/1000 Mbps LAN ports (Intel® i210 Ethernet controller), this desktop network appliance also comes with four 10 GbE SFP+ fiber ports for high bandwidth and long-distance communications. The NA362 is an excellent choice for a wide array of network applications including UTM, VPN, firewall, gateway, SD-WAN and vCPE with its enhanced security and performance. The Denverton–based NA362 features the Intel® QuickAssist Technology (Intel® QAT) for accelerated data processing including symmetric encryption and authentication, asymmetric encryption, digital signatures, RSA, DH, ECC, and lossless data compression. Furthermore, it also supports the Intel® Data Plane Development Kit (Intel® DPDK), which greatly boosts packet processing performance and throughput, allowing more time for data plane applications. The NA362 comes with either two or four DDR4 R-DIMM/U-DIMM with 64GB or 128GB of non-buffer non-ECC/ECC memory. The slim-type network communication platform is equipped with one 2.5" SATA3 HDD and one mSATA for sufficient storage. It also supports wireless communication of Wi-Fi, 3G, LTE through a PCI Express Mini Card slot. I/O options include two USB 2.0 ports and a serial console port. To ensure reliable operation, the 10-port network platform supports watchdog timer. Moreover, it also supports mainstream Yocto, Linux, Windows® Server 2012 R2, and Windows® Server 2016 operating systems.
-
Product
2-Port SFP Gigabit Base Ethernet Card With HSR/PRP
ECU-P1524PE-B
-
CE/FCC certificationSupports HSR protocol (IEC 62439-3, Clause 5)Supports PRP protocol (IEC 62439-3, Clause 4)PCI Express extension2 x SFP Interface (for Ethernet communications)2 x SFP interface (for HSR/PRP)1 x RJ45 (Interlink)Supports IEEE 1588-25 ~ 70°C operating temperature range
-
Product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PCI-C664
-
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
Product
ARINC 664 Part 7 Test & Simulation Interface for PCI Express
PCIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Dual Port Simulator Fiber Channel XMC Module
XMC-FC4 Simulyzer
Simulator
*Two independent fiber channel ports*The two SFPs accept electrical as well as optical transceivers*Each port supports 1, 2, or 4 Gbps*Supports customer-specific defined transmission speed*Comprehensive decoding of FC-1, FC-2 and Upper Layer Protocol (ULP) frames*Triggering and filtering*Supports DMA for high-speed streaming*IRIG-B time code encoder / decoder for data correlation*Supports ULPs such as FC-AE-ASM, FC-AE-RDMA, FC-AE-1553 and FC-AV*Supports HS-1760E applications such as AS5653, AS5652 and AS5627*Optional fcXplorer, Windows-based FC simulation and analysis test software*FC SDK (Software Development Kit) provides drivers and APIs for Windows XP / 7,*Linux, VxWorks, QNX Neutrino RTOS and others on request
-
Product
Intel® Xeon® E3 Quad-Core 10 Gigabit Ethernet AdvancedTCA® Processor Blade
aTCA-9300
Processor Blade
The ADLINK aTCA-9300 is a high performance AdvancedTCAR (ATCA) processor blade featuring dual 4-core IntelR XeonR processor E3 1275V2 /1225V2, IntelR C216 Chipset, four channel memory up to 32 GB of DDR3 memory and 300 W power supply subsystem. Versatile connectivity includes dual 10GbE Fabric Interfaces, dual GbE Base Interfaces, quad front panel GbE egress ports, front panel dual COM and USB 2.0 ports and front panel VGA connector. An onboard SATA connector supports CFast up to 32 GB and the optional RTM (aTCA-R6270/R6280) supports an 8-channel mini-SAS port, dual 10GbE SFP+ ports, dual USB ports and dual hot-swappable SATA bays providing additional network throughput and storage capacities.
-
Product
6U VPX Board
VP62003
-
LinkedHope Intelligent Technologies Co.,Ltd.
VP62003 is a 6U VPX board based on Intel® Xeon® D-15xx processors, with more than 7-year lifecycle. Supporting up to Intel® Xeon® D-1577 (16x 1.3GHz) processor, VP62003 is able to perform vector operation and floating point arithmetic that require high throughput. Besides, VP62003 supports Intel® Turbo Boost, with the processing speed of CPU up to 2.7GHz. The high-performance CPU and the Turbo Boost technology leave no worries for extra cost and complexity of system settings.VP62003 provides 4x Rapid I/O (SRIO) x4 for VPX Data Plane communication, 2x 8 PCIe for VPX Expansion Plane communication, 4x GbE for VPX Control Plane communication, and 2x 10Gb SFP+ in front I/O for remote data transmission and communication. Rich data exchange interfaces on VP62003 make it easy to build box-level or system-level solutions.
-
Product
Ethernet To Fiber Optic Converters (Point To Point)
-
Our rugged, industrial-grade, point-to-point Fast and Gigabit Ethernet to fiber optic converters work in pairs to extend 10/100/1000M Ethernet signals over long distance. These Fast and Gigabit Ethernet to fiber optic converters have been designed for harsh industrial environments and withstand a wide temperature of -40°F to 185°F (-40°C to 85°C), and they come with the options of multi-mode and single-mode, and ST, SC, FC, and SFP connectors.
-
Product
8-Port SFP/RJ45 Gigabit Ethernet Card
ECU-P1528
-
CE/FCC Certification8 x GbEPCI Express Extension8 x SFP Interface (for ECU-P1528PE)Operation Temp: -25 ~ 60°C
-
Product
40Gbps Ethernet Packet Generators
-
Axtrinet (AXTRINET IS A TRADING NAME )
40Gbps QSFP+ & 10Gbps SFP+ ports, Support optical & copper transceivers, Wire-rate performance on all ports, Compact & Portable, Intuitive Graphical Control Interface, Control multiple units from single GUI, Test Automation with TCL interface
-
Product
Fiber Cable, Multimode, OM3, 50m
784184-50
SFP+ Cable
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
Product
2-Port SFP Base Etheret With HSR/PRP Low Profile PCI Express Communication Card
ECU-P1522
-
CE/FCC certificationSupports HSR protocol (IEC 62439-3, Clause 5)Supports PRP protocol (IEC 62439-3, Clause 4)PCI Express® x1 compliant2 x SFP interface (for HSR/PRP)1 x RJ45 (Interlink)Support IEEE 1588-25 ~ 70°C operating temperature range
-
Product
ATCA Rear Transition Module
ART108
-
The ART108 is a Rear Transition Module (RTM) that brings expandability to Vadatech’s ATC108, ATC104, etc. carrier board. The ART108 is a passive RTM that allows for Management RS-232 serial interface and PCIe x4 lanes for expansion. The PCIe x4 is either with Fiber or Copper. The Copper interface is via I-PASS x8 PCIe connector while the Fiber interface is via quad SFP interface.
-
Product
X-Ray Detector
XRT Detector Onyx
-
ONYX 1412-X is a performance-leading X-ray detector comprising a proprietary 2768 × 2376 active pixel sensor array of 50 × 50 µm pixels. This detector consists of a high-speed, low-noise, radiation-tolerant, 14 × 12 cm, 6.6M pixel CMOS image sensor, with a directly deposited high-resolution CsI scintillator on Fibre Optic Plate. The highly configurable sensor is accessed through a software interface, connected via a 10 GbE SFP+ hardware interface.
-
Product
COM Express Type 7 10GbE Optical Fiber Network Adapter Card
10GbE Optical Fiber Network Adapter Card
Network Interface Controller
- Supports up to four 10GbE optical fiber interfaces (SFP+)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
Product
Fibre Channel XMC Interface Module
XMC-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Supports DMA for high speed streaming of data to/from the board - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
SFP+ Cable, 3m
784076-03
SFP+ Cable
1-Pin, Male SFP+ to 1-Pin, Male SFP+ or 2-Pin, LC/LC Duplex to 2-Pin, LC/LC Duplex SFP Cable - The SFP+ Cable connects to the SFP port on some PXI High-Speed Serial Instruments, PXI Ethernet Interface Modules, Controllers for FlexRIO, and USRP RIO devices. The LC/LC Duplex model has multimode and single-mode optical fiber options that you can use in tandem with SFP+ optical transceivers. The cable is rated for transmission speeds up to 10.3125 Gbps and is offered in different lengths.
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for PXI Express
PXIe-DCE
-
Avionics Interface Technologies
Supports 10/100/1000 Mbit/s Full Duplex EthernetUtilizes SFPs to support both Copper and Optical interfacesUser controlled Ethernet frame transmissions with high precision timing and scheduling
