Response
-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm
40-294-011
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Coaxial Fixed Attenuator, DC to 12.4 GHz
8491A
The Keysight 8491A coaxial fixed attenuator provides precision attenuation, flat frequency response and low SWR over broad frequency ranges. The attenuator has type-N connectors and is available in nominal attenuations of 3 dB and 6 dB, as well as 10 dB increments from 10 dB to 60 dB. This attenuator is swept-frequency tested to ensure specification compliance at all frequencies. Calibration points are provided on a nameplate chart attached to each unit.
-
product
Impedance Analyser Frequency Response Analyser
C60
The C60 investigates the opaque world of analog networks. The unit operates in two test modes. It can measure the frequency response of a two port system producing a gain/loss and phase graph. It can also measure the reactive response of a two terminal network producing an impedance/admittance and phase graph. Electronic, electrical, electro-acoustic and other networks can be tested with sine wave excitation and the results displayed on a PC.
-
product
Broadband Sensors
Offers a response between 120 sec and 160 Hz in a smaller, rugged, low power and low cost system that is easy to install and deploy. Built with ease of installation in mind, it does not require mass lock, mass centering, and has a large operational tilt range which combines to reduce installation training, time, and cost.
-
product
ICP® Shock Accelerometers
Piezoelectric ICP® accelerometers afford a very high signal output (+/- 5 volts full scale) and the ease of two-wire electrical connectivity. Their inherent ruggedness enables them to be severely over ranged without damage. The addition of internal mechanical isolation minimizes the high frequency stress that would otherwise be encountered by their ceramic sensing elements. This mechanical isolation, coupled with an internal 2-pole electrical filter, built into the ICP® circuitry, tailors the overall accelerometer response to assure data quality to frequencies as high as 10 kHz. Depending on the specific model, accelerations in excess of 50 kg can be successfully measured. These modern designs, with their internal elastomeric isolation materials are verified through calibration to remain dynamically linear and are enabling piezoelectric accelerometers to operate in increasingly severe acceleration environments.
-
product
43.5W to 66W - Single Output
iBF Series
*DOSA Compatible Footprint*2.4-5.5 Vdc, 4.5-14 Vdc Inputs*0.6-3.63 Vdc, 0.7-5.5 Vdc Outputs*Non-Isolated*Excellent Transient Response*LGA or EPC format*No external loop tuning components needed
-
product
Absorber Lined Shielding Enclosure Measurements
ALSE
Due to on-going work in the standardization committee CISPR D (responsible for CISPR 25) the latest issue CISPR 25 Ed. 4.0 has not been cited to-date. In the meantime we are able to offer two different validation procedures:
-
product
Fast Response Flow Controller for Medium Flow
HFM-305 / HFC-307
The HFM-305/HFC-307 is Teledyne Hastings' fast response series of mass flow meters and controllers. Featuring reliability and stability, the 300 Series is chosen for its fast response under a wide range of conditions. .The HFM-305 / HFC-307 meters and controllers have flow ranges from 0-1000 slm to flows of 0-2500 slm; provide analog outputs, are constructed of stainless steel and can be configured to have either normally open or normally closed valves. The full scale range is specified by the end user. A NIST traceable calibration certificate is standard. With a choice of elastomers and high pressure options, the HFM-305 / HFC-307 services a wide variety of applications. Cleaning for oxygen service is available.
-
product
Single Channel Potentiostats
ModuLab XM ECS
ModuLab XM has modularity at the center of its design. Each system can be configured for electrochemical, materials, and photoelectrochemistry measurements. At the core of each of these is the Frequency Response Analyzer. The accuracy from design to calibration is at the heart of Solartron's success and reputation for impedance measurements.
-
product
Coreless DC Motor
Citizen Chiba Precision Co., Ltd.
As the inertial momentum of the rotor and the mechanical constant of the product are both small, activation and shutdown can be swiftly performed to offer superior responsiveness.
-
product
RZ Family of 64-Bit & 32-Bit Arm-Based High-End MPUs
RZ/T
The second products in the RZ Family. These high-end controllers leverage tightly-coupled memory to achieve high speed and high responsivity, and also support multi-protocol industrial Ethernet communications.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 63.7 Ohm
50-293-011
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
-
product
Current Sensors
MCx1101 Family
Power architects are continually asked to push the boundaries for system efficiency, response time, small size, and low cost in new power system designs. Most modern designs require current sensors to help implement the complicated control, telemetry, and protection circuitry essential in meeting these difficult design goals.
-
product
Code Verification Systems for Quality Inspection
Matrix codes enable the comprehensive and seamless traceability of goods, which turns out as significant advantage considering everyday product recalls across all industries. Whether salmonella in food, contaminated cosmetics or poor components: defective products can harm consumers, cause losses of image as well as massive economic losses. Using the 2D code, each individual article can be localized globally. Based on the specific serial number, producers and consumers can clearly identify articles if required. That represents a perfect tool for determining whether the article is subject to be withdrawn from circulation. The proper application and specification of 2D code contents allows for serious and sustainable companies to limit recalls, save costs, and to take responsibility for consumer protection.
-
product
InfiniiMax Probe, 1.5 GHz
1130B
Provides extremely low input capacitance, flat frequency response, and patented resistor probe tip technology.
-
product
Type 1 Phantom Powered Measurement Microphone
MK224PH
The MK224PH Type 1 phantom powered measurement microphone system offers a cost effective solution to acoustic measurements from phantom powered sources. Frequency Response: +/-2dB (8 Hz to 18kHz). Sensitivity: 50 mV/Pa (-26 dBV/Pa)typ. Dynamic Range 3% THD: 14dBA-145dB.
-
product
Modular Test Platform
RXT Series
With extreme modularity and an open platform concept, the RXT defines the test set of the future. The RXT''s capability to combine multiple technologies into a rugged modular platform increases the productivity of technicians who are responsible for the installation, verification, and maintenance of today''s complex services.
-
product
Digital Mass Flow Controller
SEC-N100 Series
The SEC-N100 Series is suitable for a large variety of industries and applications. This mass flow controller can control a wide range of flows: from 10 SCCM to 1000 SLM. The SEC-N100 Series also has various types of communications available i.e. digital/analog, DeviceNet™, CC-Link®, PROFIBUS™, and EtherCAT®. The SEC-N100 Series offers high accuracy (+/- 1.0% S.P. *1) and high-speed response. This mass flow controller also has multi-gas/multi-range function emphasizing its' cost reduction capabilities in your process.
-
product
Combustible Monitor
SMC 5100-02-IT
The SMC 5100-02-IT gas sensor monitors combustible gases such as Methane, Hydrogen, Propane, and others. It is based on catalytic bead technology, a consistent and reliable method of detection that offers excellent response times to the target gases. The 5100-02-IT sensor offers multiple communication outputs including 4-20 mA and Modbus RTU.
-
product
Miniature Single Axis Accelerometers
Miniature piezoelectric accelerometers are required for applications demanding high frequency range, small size, and low weight. Product testing is necessary in today’s competitive marketplace in order to optimize designs, reduce defects, and improve customer acceptance and satisfaction. Shock and vibration testing offers a structured approach for verifying survivability in environmental influences that may be encountered during service and for precipitating incipient failures so they are not encountered by the end-user. PCB® accelerometers are used extensively for monitoring an object’s response to a programmed vibration input and for controlling the vibration profiles during testing.
-
product
Color / Mark Sensors
Panasonic Industrial Devices Sales Company of America
Panasonic provides Digital Color and Mark Sensors for high precision detection of any color, mark and vital indicators with high speed response times.
-
product
Very Compact Low-Frequency Control Element
750-LFC
The 750-LFC low-frequency-control element’s impressive power-to-size-ratio and versatile features make it the right choice for any application demanding superior low-frequency performance in low-profile systems. It pairs perfectly with ULTRA‑X40 and LINA systems, extending response down to 36 Hz for deeper, richer bass with total control.
-
product
PXIe-4147, 4-Channel, ±8 V, 3 A Precision PXIe Source Measure Unit
786888-01
PXIe, 4-Channel, ±8 V, 3 A Precision PXI Source Measure Unit - The PXIe-4147 is a 4-channel source measure unit (SMU) ideal for high-pin-count applications. It features 4-quadrant operation, and each channel has integrated remote four-wire sensing for accurate measurements. The sample rate of the PXIe-4147 can reduce measurement times, capture transient device characteristics, and help you perform current-voltage (I-V) characterization of devices-under-test (DUTs). With a high-speed sequencing engine, you can synchronize SMUs with each other or with other instruments such as switches or high-speed digital test modules. Additionally, you can tune the PXIe-4147 response to any load to achieve optimum responses with maximum stability and minimum transients using SourceAdapt technology.
-
product
PIN Photodiode
PIN photodiode is a kind of photo detector, it can convert optical signals into electrical signals.This technology was invented in the latest of 1950's. There are three regions in this type of diode. There is a p-region an intrinsic region and an n-region. The p-region and n-region are comparatively heavily doped than the p-region and n-region of usual p-n diodes. The width of the intrinsic region should be larger than the space charge width of a normal p-n junction. The PIN photo diode operates with an applied reverse bias voltage and when the reverse bias is applied, the space charge region must cover the intrinsic region completely. Electron hole pairs are generated in the space charge region by photon absorption. The switching speed of frequency response of photo diode is inversely proportional to the life time. The switching speed can be enhanced by a small minority carrier lifetime. For the photo detector applications where the speed of response is important, the depletion region width should be made as large as possible for small minority carrier lifetime as a result the switch speed also increases.
-
product
Pressure Sensors For Blast Testing
Pressure sensors with quartz, ceramic and tourmaline sensing elements are used for a wide variety of shock wave, blast and explosive testing. All of these applications require high frequency response and durability, ability to drive long cables and operate in adverse environments.
-
product
Process NIR Analyzers
Process near-infrared (NIR) analyzers continuously measure moisture, oil, coat weight and other parameters directly in manufacturing processes for responsive process control. Common industries include wood products, tobacco, snack foods, converting, and bulk materials. A variety of sample interfaces, environmentally rated enclosures, and interface options are available for easy implementation and integration.
-
product
Computerized Knife-Edge Tomography (CKET)
Many new generation lasers, having a spectrum which is out of the sensitivity response of typical camera detectors require different technologies to be ex-amined. Tomographic knife-edge technology offers a feasible solution. Multiple knife-edges scanning from different directions provide beam profiles depen-dent on scanning angle. By reconstruction techniques used in tomography, an image-like profile can be reconstructed and analyzed. Various detectors are used to provide a wide spectral range measurement capability
-
product
RDM Responder Tests
The RDM Responder Tests are an automated testing suite for RDM Responders. Testing RDM Responses previously involved connecting an RDM Controller and sending commands to the responder, verifying the behavior matched what was expected. This can be a time consuming process and many of the corner cases aren't exercised.
-
product
Omni Measuring Microphone
PVR™ 2
Omni-directional microphone for free-field measurement. With a highly reliable circuit and a 1/4" pre-polarized condenser capsule, it boasts high stability, low distortion and low noise in performance. Its excellent flat frequency response makes it ideal for sonic analysis systems and recording.
