Showing results: 226 - 240 of 4029 items found.
-
CU-V Series -
Mors Smitt Group
The CU-V is a so called safety relay which is used in places where a safe separation between coil and contact circuit is required. The relay is, with the corresponding screw socket V12, according to CEE 15/2e edition, approved by KEMA, for application in gas fired installations.
-
CU-U Series -
Mors Smitt Group
The CU-U is a so called safety relay which is used in places where a safe separation between coil and contact circuit is required. The relay is, with the corresponding screw socket V12, according to CEE 15/2e edition, approved by KEMA, for application in gas fired installations.
-
Delta Series -
Mors Smitt Group
The Delta relays provides a robust and reliable interface between protection and control system circuits. A more economical alternative to traditional auxiliary, trip and supervision relays, the Delta provides a compact, flexible and high performance solution while meeting relevant IEC standards.
-
DI Series -
Mors Smitt Group
Heavy duty, current monitoring relay for demanding applications. Current activated coil.
-
-
Falcon Electric, Inc
*UPS Monitoring. Falcon’s Dry Contact Relay Card facilitates UPS status via configurable relay contact activation for simple integration into existing PLC/ monitoring systems.*Flexible Configuration. Easily installs into all SSG and SSG-RP UPS models. Configurable to allow simple selection of active open or closed relay contacts.*Notification & Remote Shutdown Capability. Provides relay contact activation during a UPS event including utility power loss, low battery, UPS fault and bypass condition. Supports safe shutdown of the UPS after a utility power loss event.*Simple Integration. The detachable connection facilitates simple integration into existing programmable logic controller (PLC) or management systems.
-
Series 86 -
Pickering Electronics
General purpose relays - As series 80 and 88 but with coil resistances typically twice as high
-
Series ST -
Teledyne Defense Electronics Relays & Coax Switch
Series ST relays are designed for high-power applications. The design incorporates an SCR or triac output. The relays utilize optical isolation to protect the control from load transients. A control LED is available on certain models. Internal MOV is also available on ST24D 25A and 50A models.​ All Series ST relays are Zero-Cross switching.Available options include:ST24D12 12A, 12-280Vrms, 600Vpeak Load; 4-30Vdc Control​ST24D25 25A, 12-280Vrms, 600Vpeak Load; 4-30Vdc ControlST48D50 50A, 24-600Vrms, 1200Vpeak Load; 5-30Vdc Control
-
Mors Smitt Group
The 1X serie is comprised of an electromechanical voltage operated relay which is wired across the circuit being monitored. The relay may be ordered to operate in one of four (4) different application modes as described in the Technical Bulletin.The relay is designed for flush mounting utilizing a single 25mm diameter mounting hole which also houses the large LED indicator. Electrical termination is made via four screw terminals on the rear of the case. This terminal block is of a plug in type with integrated retention screws further simplifying installation.
-
-
-
PX8500 -
TEAM SOLUTIONS, INC.
The PX8500 is an external 8-channel relay board for the connection of digital output boards. It can be cascaded in 16, 24 and 32 relays and is intended for mounting on DIN supporting rails. The board provides a convenient interface between an industrialprocess and the SUB-D connectors on ADDI-DATA boards. The change-over contacts of the relay are controlled through 24 V signals. The 24 V voltage supply is protected through varistors and transil diodes. The board is intended for the use with 220 V supply. The creeping distance (acc. to DIN VDE0110) and the connector cross sections allows high-power switching (up to 2,500 VA).
-
SparkFun Electronics
Have you ever wanted to control something powerful or have you ever needed to turn on/off a high power device from your Arduino or another low powered microcontroller? The SparkFun Qwiic Single Relay provides you with the easiest to use relay yet. The Single Relay board can handle up to 5.5A at 240VAC for long periods of time and allows you to control large power loads with simple I2C commands. Utilizing our handy Qwiic system, and on-board screw terminals, no soldering is required to connect it to the rest of your system!
-
D-E Series -
Mors Smitt Group
Heavy duty relays for demanding applications, suitable for low current switching, equipped with gold plated contacts.
-
DGG Series -
Mors Smitt Group
Heavy duty relays wth extremely sensitive coil (pull-in 0,4 x Unom) for demanding applications.